Re: [PATCH 7/7] arm64: dts: qcom: Add support for the Xiaomi SM7125 platform

[Konrad Dybcio]

On 4.07.2023 18:32, David Wronek wrote:
> There are 6 Xiaomi smartphones with the SM7125 SoC:
> 
> - POCO M2 Pro (gram)
> - Redmi Note 9S (curtana)
> - Redmi Note 9 Pro (Global, joyeuse)
> - Redmi Note 9 Pro (India, curtana)
> - Redmi Note 9 Pro Max (excalibur)
> - Redmi Note 10 Lite (curtana)
> 
> These devices share a common board design (a.k.a miatoll) with only a
> few differences. Add support for the common board, as well as support
> for the global Redmi Note 9 Pro.
> 
> Signed-off-by: David Wronek <davidwronek@xxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/sm7125-xiaomi-joyeuse.dts   |  16 +
>  .../boot/dts/qcom/sm7125-xiaomi-miatoll.dtsi  | 420 ++++++++++++++++++
>  3 files changed, 437 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sm7125-xiaomi-joyeuse.dts
>  create mode 100644 arch/arm64/boot/dts/qcom/sm7125-xiaomi-miatoll.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 337abc4ceb17..7ef9e7d43904 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -192,6 +192,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-xiaomi-laurel-sprout.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6375-sony-xperia-murray-pdx225.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sm7125-xiaomi-joyeuse.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm7225-fairphone-fp4.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-microsoft-surface-duo.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm7125-xiaomi-joyeuse.dts b/arch/arm64/boot/dts/qcom/sm7125-xiaomi-joyeuse.dts
> new file mode 100644
> index 000000000000..670fd63f3416
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm7125-xiaomi-joyeuse.dts
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023, David Wronek <davidwronek@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "sm7125-xiaomi-miatoll.dtsi"
> +
> +/ {
> +	model = "Xiaomi Redmi Note 9 Pro (Global)";
> +	compatible = "xiaomi,joyeuse", "qcom,sm7125";
> +
> +	/* required for bootloader to select correct board */
> +	qcom,board-id = <0x50022 1>;
I think you need to amend some list in bindings to allow qcom,abcd-id properties

[...]

> +		rmtfs_mem: memory@fa601000 {
> +			compatible = "qcom,rmtfs-mem";
> +			reg = <0x0 0xfa601000 0x0 0x200000>;
> +			no-map;
> +
> +			qcom,client-id = <1>;
> +			qcom,vmid = <15>;
QCOM_SCM_VMID_MSS_MSA

from

include/dt-bindings/firmware/qcom,scm.h

> +		};
> +	};
> +};
> +
> +&apps_rsc {
> +	regulators-0 {
> +		compatible = "qcom,pm6150-rpmh-regulators";
> +		qcom,pmic-id = "a";
> +
> +		vreg_s1a_1p1: smps1 {
> +			regulator-min-microvolt = <1128000>;
> +			regulator-max-microvolt = <1128000>;
> +		};
> +
> +		vreg_s4a_1p0: smps4 {
> +			regulator-min-microvolt = <824000>;
> +			regulator-max-microvolt = <1120000>;
> +		};
> +
> +		vreg_s5a_2p0: smps5 {
> +			regulator-min-microvolt = <1744000>;
> +			regulator-max-microvolt = <2040000>;
> +		};
> +
> +		vreg_l1a_1p2: ldo1 {
> +			regulator-min-microvolt = <1178000>;
> +			regulator-max-microvolt = <1256000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
You want HPM, LPM is not guaranteed to give you the desired voltages.

[...]

> +&sdhc_2 {
> +	status = "okay";
Status last, everywhere

Konrad
> +
> +	pinctrl-names = "default","sleep";
> +	pinctrl-0 = <&sdc2_on>;
> +	pinctrl-1 = <&sdc2_off>;
> +	vmmc-supply = <&vreg_l9c_2p9>;
> +	vqmmc-supply = <&vreg_l6c_3p0>;
> +
> +	cd-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <0 4>, <34 4>, <59 4>;
> +
> +	sdc2_on: sdc2-on-state {
> +		clk-pins {
> +			pins = "sdc2_clk";
> +			bias-disable;
> +			drive-strength = <16>;
> +		};
> +
> +		cmd-pins {
> +			pins = "sdc2_cmd";
> +			bias-pull-up;
> +			drive-strength = <10>;
> +		};
> +
> +		data-pins {
> +			pins = "sdc2_data";
> +			bias-pull-up;
> +			drive-strength = <10>;
> +		};
> +
> +		sd-cd-pins {
> +			pins = "gpio69";
> +			function = "gpio";
> +			bias-pull-up;
> +			drive-strength = <2>;
> +		};
> +	};
> +
> +	sdc2_off: sdc2-off-state {
> +		clk-pins {
> +			pins = "sdc2_clk";
> +			bias-disable;
> +			drive-strength = <2>;
> +		};
> +
> +		cmd-pins {
> +			pins = "sdc2_cmd";
> +			bias-pull-up;
> +			drive-strength = <2>;
> +		};
> +
> +		data-pins {
> +			pins = "sdc2_data";
> +			bias-pull-up;
> +			drive-strength = <2>;
> +		};
> +
> +		sd-cd-pins {
> +			pins = "gpio69";
> +			function = "gpio";
> +			bias-pull-up;
> +			drive-strength = <2>;
> +		};
> +	};
> +};
> +
> +&usb_1 {
> +	qcom,select-utmi-as-pipe-clk;
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +	maximum-speed = "high-speed";
> +	dr_mode = "peripheral";
> +	status = "okay";
> +};
> +
> +&usb_1_hsphy {
> +	vdd-supply = <&vreg_l4a_0p88>;
> +	vdda-pll-supply = <&vreg_l11a_1p8>;
> +	vdda-phy-dpdm-supply = <&vreg_l17a_3p1>;
> +	status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> +	status = "okay";
> +	vdda-phy-supply = <&vreg_l4a_0p88>;
> +	vdda-pll-supply = <&vreg_l3c_1p23>;
> +};