**
Please CC me on replies to this
I'm using a off-list email to try not to miss anything in the mail flood my
normal box gets
**
I'm concerned that it's going to get left by the wayside in 2.2...so here's
my own SMP problem book.
I'm still having massive problems with SMP support on 2.2.10-2.2.15 and all
PRE's in
between. Likely before then, but that's as far back as I can remember at
the moment.
Essentially, I've never had 2.2 OR 2.3 work in SMP mode w/o problems.
However,
the last 2.3 version I tried was in January of 2000.
The symptoms are one of the following, within 4 hours of system start
(usually within 45 minutes):
Hard lock
This is the most common
Kernel panic with unable to handle kernel paging request
This has gone away it seems, since i added another 128mb of
ram
Lock with IRQ errors on console
Unlogged, i can't recall the exact text at the moment
The statement is that IRQ's are being shut down because of
too many interupts.
This particular error stopped being funny a few months back
:)
Network shutdown.
All services running, machine 100% responsive from console,
but no network,
not even ping. Interfaces show as up. Cycling them has no
effect.
I've tried:
noapic -- per AC suggestion, no change.
Different motherboard (Same make/model however)
Different memory
HD's have been replaced since this started, always UDMA33 drives,
either Maxtor (previous) or IBM boot and Maxtor data (current)
HD controller had been replaced as a test w/ a PCI UDMA66
controller, no change.
Kernel has Andre Hedrick's<sp?> IDE patches applied, always.
Without them it is far less stable, even in UP.
If I run with nosmp as a kernel option (sigh, it's my default lilo config
these days), the
system will _usually_ stay up as least as long as the next kernel pre-patch.
Always
at least a week in UP, however. When it fails in UP, it does so with the
same
symptoms as SMP.
The system is a webserver, running httpd,mysqld,and sendmail. It handles
about
3K emails per day, and roughly 7 million http requests per day. It handles
those
requests much better during the short times it has the full use of it's
processors. :)
If anyone has anything they'd like me to try to assist in debugging i'm up
for it.
ALSO, and on a separate note:
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634029
This particular error (bit already cleared) started occuring with
2.2.15pre-something (low, like 4 or so)
Appended is the output from: ver_linux, lspci, bootup log, hdparm, and
kernel config.
********** ver_linux
Linux quark 2.2.15pre17 #2 SMP Tue Apr 4 15:16:57 PDT 2000 i686 unknown
Kernel modules 2.1.121
Gnu C 2.95.1
Binutils 2.9.5.0.16
awk: GNU Awk 3.0.3
Dynamic linker ldd (GNU libc) 2.1.2
Procps 2.0.6
Mount 2.9v
Kbd 0.99
Sh-utils 2.0
cat: /proc/modules: No such file or directory
********** lspci:
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(rev 02)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev
02)
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
00:0f.0 Ethernet controller: Digital Equipment Corporation DECchip 21140
[FasterNet] (rev 12)
00:10.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 30)
00:14.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2064W
[Millennium] (rev 01)
********** bootup logs:
Linux version 2.2.15pre17 (root@quark) (gcc version 2.95.1 19990816
(release)) #2 SMP Tue Apr 4 15:16:57 PDT 2000
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: INTEL Product ID: 440BX APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bootup CPU
Processor #1 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Detected 400917823 Hz processor.
ide_setup: hdc=ide-scsi
Console: colour VGA+ 80x25
Calibrating delay loop... 799.54 BogoMIPS
Memory: 517484k/524288k available (916k kernel code, 424k reserved, 5412k
data, 52k init)
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k)
Page cache hash table entries: 131072 (order 7, 512k)
VFS: Diskquotas version dquot_6.4.0 initialized
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
per-CPU timeslice cutoff: 100.22 usecs.
CPU0: Intel Pentium II (Deschutes) stepping 02
SMP mode deactivated, forcing use of dummy APIC emulation.
Getting VERSION: 40011
Getting VERSION: 40011
Getting LVT0: 700
Getting LVT1: 400
setup_APIC_clock() called.
calibrating APIC timer ...
..... 4009097 CPU clocks in 1 timer chip tick.
..... 1002272 APIC bus clocks in 1 timer chip tick.
..... CPU clock speed is 400.9097 MHz.
..... system bus clock speed is 100.2272 MHz.
CPU map: 3
CPU #1 not responding. Removing from cpu_online_map.
Before bogomips.
Error: only one processor found.
Boot done.
enabling symmetric IO mode... ...done.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-3, 2-4, 2-10, 2-18, 2-20, 2-21, 2-22, 2-23 not
connected.
number of MP IRQ sources: 17.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 0 0 0 0 0 1 1 59
02 0FF 0F 0 0 0 0 0 1 1 51
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 0 0 0 0 0 1 1 61
06 000 00 0 0 0 0 0 1 1 69
07 000 00 0 0 0 0 0 1 1 71
08 000 00 0 0 0 0 0 1 1 79
09 000 00 0 0 0 0 0 1 1 81
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 0 0 0 0 0 1 1 89
0c 000 00 0 0 0 0 0 1 1 91
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 0 0 0 0 0 1 1 99
0f 000 00 0 0 0 0 0 1 1 A1
10 0FF 0F 1 1 0 1 0 1 1 A9
11 0FF 0F 1 1 0 1 0 1 1 B1
12 000 00 1 0 0 0 0 0 0 00
13 0FF 0F 1 1 0 1 0 1 1 B9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 2
IRQ1 -> 1
IRQ3 -> 17
IRQ4 -> 16
IRQ5 -> 5
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ9 -> 9
IRQ10 -> 19
IRQ11 -> 11
IRQ12 -> 12
IRQ13 -> 13
IRQ14 -> 14
IRQ15 -> 15
.................................... done.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xfdb81
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:3a
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Starting kswapd v 1.5
Real Time Clock Driver v1.09
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 40MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DJNA-371350, ATA DISK drive
hdb: Maxtor 92720U8, ATA DISK drive
hdc: CR-2801TE, ATAPI CDROM drive
hdd: Maxtor 92720U8, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: IBM-DJNA-371350, 12949MB w/1966kB Cache, CHS=1650/255/63, UDMA(33)
hdb: Maxtor 92720U8, 25965MB w/2048kB Cache, CHS=3310/255/63, UDMA(33)
hdd: Maxtor 92720U8, 25965MB w/2048kB Cache, CHS=52755/16/63, UDMA(33)
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 1 host.
Vendor: MITSUMI Model: CR-2801TE Rev: 1.07
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI cdrom total.
sr0: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
Uniform CDROM driver Revision: 2.56
3c59x.c:v0.99H 11/17/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xe880, 00:50:da:18:57:aa, IRQ 3
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
MII transceiver found at address 0, status 786d.
Enabling bus-master transmits and whole-frame receives.
Partition check:
hda: hda1 hda2 hda3
hdb: hdb1
hdd: hdd1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 52k freed
VFS: Disk change detected on device sr(11,0)
ISO 9660 Extensions: RRIP_1991A
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634029
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634030
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634031
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634029
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634030
EXT2-fs warning (device ide0(3,1)): ext2_free_inode: bit already cleared for
inode 1634031
********** hdparm
/dev/hda: (root)
multcount = 16 (on)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1650/255/63, sectors = 26520480, start = 0
/dev/hdb: (/home)
multcount = 16 (on)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 3310/255/63, sectors = 53177040, start = 0
/dev/hdd: (unmounted)
multcount = 16 (on)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 52755/16/63, sectors = 53177040, start = 0
********* kernel config
#
# Automatically generated by make menuconfig: don't edit
#
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
CONFIG_M686=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_1GB=y
# CONFIG_2GB is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_SMP=y
#
# Loadable module support
#
# CONFIG_MODULES is not set
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_QUIRKS=y
# CONFIG_PCI_OPTIMIZE is not set
CONFIG_PCI_OLD_PROC=y
# CONFIG_MCA is not set
# CONFIG_VISWS is not set
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_BINFMT_JAVA is not set
# CONFIG_PARPORT is not set
# CONFIG_APM is not set
#
# Plug and Play support
#
CONFIG_PNP=y
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
CONFIG_IDEDMA_NEW_DRIVE_LISTINGS=y
CONFIG_IDEDMA_PCI_EXPERIMENTAL=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD7409 is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
CONFIG_BLK_DEV_PIIX=y
CONFIG_PIIX_TUNING=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_BOOT is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_DEV_DAC960 is not set
CONFIG_PARIDE_PARPORT=y
# CONFIG_PARIDE is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_DEV_HD is not set
#
# Networking options
#
# CONFIG_PACKET is not set
# CONFIG_NETLINK is not set
# CONFIG_FIREWALL is not set
# CONFIG_FILTER is not set
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_IP_ROUTER is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
CONFIG_IP_ALIAS=y
CONFIG_SYN_COOKIES=y
# CONFIG_INET_RARP is not set
CONFIG_SKB_LARGE=y
# CONFIG_IPV6 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_BRIDGE is not set
# CONFIG_LLC is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
# CONFIG_CPU_IS_SLOW is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
#
# SCSI support
#
CONFIG_SCSI=y
# CONFIG_BLK_DEV_SD is not set
# CONFIG_CHR_DEV_ST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_SCSI is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
CONFIG_EL3=y
# CONFIG_3C515 is not set
CONFIG_VORTEX=y
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_RTL8139 is not set
# CONFIG_NET_ISA is not set
# CONFIG_NET_EISA is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_RADIO is not set
#
# Token ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_HOSTESS_SV11 is not set
# CONFIG_COSA is not set
# CONFIG_SEALEVEL_4021 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_COMX is not set
# CONFIG_DLCI is not set
# CONFIG_SBNI is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
# CONFIG_SERIAL is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_UNIX98_PTYS is not set
# CONFIG_MOUSE is not set
#
# Joysticks
#
# CONFIG_JOYSTICK is not set
# CONFIG_QIC02_TAPE is not set
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=y
#
# Video For Linux
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DTLK is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
#
# Filesystems
#
CONFIG_QUOTA=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_FAT_FS is not set
# CONFIG_MSDOS_FS is not set
# CONFIG_UMSDOS_FS is not set
# CONFIG_VFAT_FS is not set
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_MINIX_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
# CONFIG_EFS_FS is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
CONFIG_NFS_FS=y
# CONFIG_NFSD is not set
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
# CONFIG_SMB_FS is not set
# CONFIG_NCP_FS is not set
#
# Partition Types
#
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MAC_PARTITION is not set
# CONFIG_SMD_DISKLABEL is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_NLS=y
#
# Native Language Support
#
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set
# CONFIG_MDA_CONSOLE is not set
# CONFIG_FB is not set
#
# Sound
#
# CONFIG_SOUND is not set
#
# Kernel hacking
#
# CONFIG_MAGIC_SYSRQ is not set
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Apr 15 2000 - 21:00:22 EST