On Tue, Mar 21, 2000 at 08:54:59PM -0800, Andre Hedrick wrote:
> On Tue, 21 Mar 2000, Simon Kirby wrote:
>
> > On Tue, Mar 21, 2000 at 12:56:55PM -0800, Andre Hedrick wrote:
> >
> > > OH MY !!!!............
> > >
> > > You know that WDC blows of the UDMA CRC and you are pumping data at
> > > ATA-3/4/5 trasfer rates with ATA-2 correction/dectection, which equals
> > > NONE!!!!!!!!
> >
> > Hrmm... Well, I don't see any bit errors, just mismapped blocks of data.
>
> BINGO!!!!!
>
> Blowing off the CRC errors means incomplete data WRITES.
Ah, I guess that would make sense. :)
> > 00:04.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
> > [sroot@oof:/root]# lspci -bxxxs 00:04.1
> > 00:04.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
> > 40: 77 e3 07 a3 0b 00 00 00 07 00 22 02 00 00 00 00
> 4 pio 2 hdb UDMA 2
> 4 pio & sitre 1 hda UDMA 2
> 4 pio ! sitre 4 hdc UDMA 2
>
> It did setup correctly but what does hdparm -i /dev/hda|b|c ?
[sroot@oof:/d]# hdparm -i /dev/hda
/dev/hda:
Model=WDC WD273BA, FwRev=P78OA30A, SerialNo=WD-WT9630110245
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=3(DualPortCache), BuffSize=1961kB, MaxMultSect=16, MultSect=8
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=53464320
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4
[sroot@oof:/d]# hdparm -i /dev/hdb
/dev/hdb:
Model=WDC WD273BA, FwRev=P78OA30A, SerialNo=WD-WM9630042296
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=3(DualPortCache), BuffSize=1961kB, MaxMultSect=16, MultSect=8
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=53464320
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4
[sroot@oof:/d]# hdparm -i /dev/hdc
/dev/hdc:
Model=WDC AC28400R, FwRev=15.01J55, SerialNo=WD-WM6280160205
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=512kB, MaxMultSect=16, MultSect=8
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=16514064
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:160,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2
Simon-
[ Stormix Technologies Inc. ][ NetNation Communcations Inc. ]
[ sim@stormix.com ][ sim@netnation.com ]
[ Opinions expressed are not necessarily those of my employers. ]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu Mar 23 2000 - 21:00:35 EST