Re: [RFC PATCH 02/13] dt-bindings: pinctrl: renesas: Document RZ/V2H(P) SoC

From: Lad, Prabhakar
Date: Wed Mar 27 2024 - 15:00:54 EST


Hi Rob,

Thank you for the review.

On Wed, Mar 27, 2024 at 5:24 PM Rob Herring <robh@xxxxxxxxxx> wrote:
>
> On Tue, Mar 26, 2024 at 10:28:33PM +0000, Prabhakar wrote:
> > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> >
> > Add documentation for the pin controller found on the Renesas RZ/V2H(P)
> > (R9A09G057) SoC. Compared to RZ/G2L family of SoCs there are slight
> > differences on the RZ/V2H(P) SoC for pinmuxing.
> >
> > Also add 'renesas-rzv2h,output-impedance' property. Drive strength
> > setting on RZ/V2H(P) depends on the different power rails which are
> > coming out from the PMIC (connected via i2c). These power rails
> > (required for drive strength) can be 1.2/1.8/3.3V.
> >
> > Pin are grouped into 4 groups,
> >
> > Group1: Impedance
> > - 150/75/38/25 ohms (at 3.3 V)
> > - 130/65/33/22 ohms (at 1.8 V)
> >
> > Group2: Impedance
> > - 50/40/33/25 ohms (at 1.8 V)
> >
> > Group3: Impedance
> > - 150/75/37.5/25 ohms (at 3.3 V)
> > - 130/65/33/22 ohms (at 1.8 V)
> >
> > Group4: Impedance
> > - 110/55/30/20 ohms (at 1.8 V)
> > - 150/75/38/25 ohms (at 1.2 V)
> >
> > 'renesas-rzv2h,output-impedance' property as documented which can be
> > [1, 2, 4, 6] indicates x Value strength.
>
> Looks like the values are x1, x1.5, x3ish, x6...
>
> >
> > As the power rail information cannot be available very early in the
> > boot process as 'renesas-rzv2h,output-impedance' property is added
> > instead of reusing output-impedance-ohms property.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > ---
> > .../pinctrl/renesas,rzg2l-pinctrl.yaml | 22 +++++++++++++++----
> > 1 file changed, 18 insertions(+), 4 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> > index 881e992adca3..77f4fc7f4a21 100644
> > --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> > +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> > @@ -26,6 +26,7 @@ properties:
> > - renesas,r9a07g043-pinctrl # RZ/G2UL{Type-1,Type-2} and RZ/Five
> > - renesas,r9a07g044-pinctrl # RZ/G2{L,LC}
> > - renesas,r9a08g045-pinctrl # RZ/G3S
> > + - renesas,r9a09g057-pinctrl # RZ/V2H(P)
> >
> > - items:
> > - enum:
> > @@ -66,10 +67,14 @@ properties:
> > maxItems: 1
> >
> > resets:
> > - items:
> > - - description: GPIO_RSTN signal
> > - - description: GPIO_PORT_RESETN signal
> > - - description: GPIO_SPARE_RESETN signal
> > + oneOf:
> > + - items:
> > + - description: GPIO_RSTN signal
> > + - description: GPIO_PORT_RESETN signal
> > + - description: GPIO_SPARE_RESETN signal
> > + - items:
> > + - description: PFC main reset
> > + - description: Reset for the control register related to WDTUDFCA and WDTUDFFCM pins
> >
> > additionalProperties:
> > anyOf:
> > @@ -111,6 +116,15 @@ additionalProperties:
> > output-high: true
> > output-low: true
> > line-name: true
> > + renesas-rzv2h,output-impedance:
>
> 'renesas-rzv2h' is not a vendor.
>
I will update this to "renesas,output-impedance".

> That should give you a warning if you actually used this somewhere.
>
I did run dtbs_check with this property in the DTS and haven't seen
any warning. Also now I included this property in the example node in
the binding doc and seen no warnings reported by dt_binding_check too.

> > + description: |
> > + Output impedance for pins on RZ/V2H(P) SoC.
> > + x1: Corresponds to 0 in IOLH register.
> > + x2: Corresponds to 1 in IOLH register.
> > + x4: Corresponds to 2 in IOLH register.
> > + x6: Corresponds to 3 in IOLH register.
>
> Why not just use 0-3 for the values?
>
Fine by me. I'll update this in the next version.

Cheers,
Prabhakar