Re: [RFC PATCH 02/13] dt-bindings: pinctrl: renesas: Document RZ/V2H(P) SoC

[Rob Herring]

On Tue, Mar 26, 2024 at 10:28:33PM +0000, Prabhakar wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> 
> Add documentation for the pin controller found on the Renesas RZ/V2H(P)
> (R9A09G057) SoC. Compared to RZ/G2L family of SoCs there are slight
> differences on the RZ/V2H(P) SoC for pinmuxing.
> 
> Also add 'renesas-rzv2h,output-impedance' property. Drive strength
> setting on RZ/V2H(P) depends on the different power rails which are
> coming out from the PMIC (connected via i2c). These power rails
> (required for drive strength) can be 1.2/1.8/3.3V.
> 
> Pin are grouped into 4 groups,
> 
> Group1: Impedance
> - 150/75/38/25 ohms (at 3.3 V)
> - 130/65/33/22 ohms (at 1.8 V)
> 
> Group2: Impedance
> - 50/40/33/25 ohms (at 1.8 V)
> 
> Group3: Impedance
> - 150/75/37.5/25 ohms (at 3.3 V)
> - 130/65/33/22 ohms (at 1.8 V)
> 
> Group4: Impedance
> - 110/55/30/20 ohms (at 1.8 V)
> - 150/75/38/25 ohms (at 1.2 V)
> 
> 'renesas-rzv2h,output-impedance' property as documented which can be
> [1, 2, 4, 6] indicates x Value strength.

Looks like the values are x1, x1.5, x3ish, x6...

> 
> As the power rail information cannot be available very early in the
> boot process as 'renesas-rzv2h,output-impedance' property is added
> instead of reusing output-impedance-ohms property.
> 
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> ---
>  .../pinctrl/renesas,rzg2l-pinctrl.yaml        | 22 +++++++++++++++----
>  1 file changed, 18 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> index 881e992adca3..77f4fc7f4a21 100644
> --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> @@ -26,6 +26,7 @@ properties:
>                - renesas,r9a07g043-pinctrl # RZ/G2UL{Type-1,Type-2} and RZ/Five
>                - renesas,r9a07g044-pinctrl # RZ/G2{L,LC}
>                - renesas,r9a08g045-pinctrl # RZ/G3S
> +              - renesas,r9a09g057-pinctrl # RZ/V2H(P)
>  
>        - items:
>            - enum:
> @@ -66,10 +67,14 @@ properties:
>      maxItems: 1
>  
>    resets:
> -    items:
> -      - description: GPIO_RSTN signal
> -      - description: GPIO_PORT_RESETN signal
> -      - description: GPIO_SPARE_RESETN signal
> +    oneOf:
> +      - items:
> +          - description: GPIO_RSTN signal
> +          - description: GPIO_PORT_RESETN signal
> +          - description: GPIO_SPARE_RESETN signal
> +      - items:
> +          - description: PFC main reset
> +          - description: Reset for the control register related to WDTUDFCA and WDTUDFFCM pins
>  
>  additionalProperties:
>    anyOf:
> @@ -111,6 +116,15 @@ additionalProperties:
>          output-high: true
>          output-low: true
>          line-name: true
> +        renesas-rzv2h,output-impedance:

'renesas-rzv2h' is not a vendor.

That should give you a warning if you actually used this somewhere.

> +          description: |
> +            Output impedance for pins on RZ/V2H(P) SoC.
> +            x1: Corresponds to 0 in IOLH register.
> +            x2: Corresponds to 1 in IOLH register.
> +            x4: Corresponds to 2 in IOLH register.
> +            x6: Corresponds to 3 in IOLH register.

Why not just use 0-3 for the values? 


> +          $ref: /schemas/types.yaml#/definitions/uint32
> +          enum: [1, 2, 4, 6]
>  
>      - type: object
>        additionalProperties:
> -- 
> 2.34.1
>