Re: [DMARC error][DKIM error] [PATCH 3/4] arm64: dts: add support for A4 based Amlogic BA400
From: Neil Armstrong
Date: Thu Mar 14 2024 - 05:04:51 EST
On 14/03/2024 06:19, Xianwei Zhao wrote:
Hi Dmitry,
Thanks for your review.
On 2024/3/13 17:53, Dmitry Rokosov wrote:
[????????? ddrokosov@xxxxxxxxxxxxxxxxx ????????? https://aka.ms/LearnAboutSenderIdentification?????????????]
[ EXTERNAL EMAIL ]
Hello Xianwei,
On Tue, Mar 12, 2024 at 05:18:59PM +0800, Xianwei Zhao via B4 Relay wrote:
From: Xianwei Zhao <xianwei.zhao@xxxxxxxxxxx>
Amlogic A4 is an application processor designed for smart audio
and IoT applications.
Add basic support for the A4 based Amlogic BA400 board, which describes
the following components: CPU, GIC, IRQ, Timer and UART.
These are capable of booting up into the serial console.
Signed-off-by: Xianwei Zhao <xianwei.zhao@xxxxxxxxxxx>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts | 43 ++++++++++
arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi | 99 ++++++++++++++++++++++
3 files changed, 143 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 1ab160bf928a..9a50ec11bb8d 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,4 +1,5 @@
# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MESON) += amlogic-a4-a113l2-ba400.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-an400.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-khadas-vim4.dtb
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts b/arch/arm64/boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts
new file mode 100644
index 000000000000..60f9f23858c6
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "amlogic-a4.dtsi"
+
+/ {
+ model = "Amlogic A113L2 ba400 Development Board";
+ compatible = "amlogic,ba400","amlogic,a4";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart_b;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 52 MiB reserved for ARM Trusted Firmware */
+ secmon_reserved:linux,secmon {
+ compatible = "shared-dma-pool";
+ no-map;
+ alignment = <0x0 0x400000>;
+ reg = <0x0 0x05000000 0x0 0x3400000>;
+ };
+ };
+};
+
+&uart_b {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi
new file mode 100644
index 000000000000..7e8745010b52
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+/ {
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gic: interrupt-controller@fff01000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x0 0xfff01000 0 0x1000>,
+ <0x0 0xfff02000 0 0x2000>,
+ <0x0 0xfff04000 0 0x2000>,
+ <0x0 0xfff06000 0 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ apb@fe000000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xfe000000 0x0 0x480000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+
+ uart_b: serial@7a000 {
+ compatible = "amlogic,meson-s4-uart",
If I'm not wrong, you need to create dt-binding alias for meson-a4-uart
and use it as 3rd compatible string.
Please add an A4 and A5 compatible using amlogic,meson-s4-uart as fallback,
and drop the ao-uart since there's no more AO uart.
Follow how it was done for the T7 in Documentation/devicetree/bindings/serial/amlogic,meson-uart.yaml
The amlogic,meson-s4-uart will provide an earlycon like ao-uart did.
Thanks,
Neil
On UART module, A4 and A5 SoCs exactly the same as S4. There's no difference.
+ "amlogic,meson-ao-uart";
+ reg = <0x0 0x7a000 0x0 0x18>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&xtal>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.37.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-amlogic
--
Thank you,
Dmitry