Re: [PATCH v3 2/2] drm/bridge: adv7511: get edid in hpd_work to update CEC phys address

[Jani Nikula]

On Mon, 19 Feb 2024, Alvin Šipraga <alvin@xxxxxxx> wrote:
> From: Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
>
> The adv7511 driver is solely responsible for setting the physical
> address of its CEC adapter. To do this, it must read the EDID. However,
> EDID is only read when either the drm_bridge_funcs :: get_edid or
> drm_connector_helper_funcs :: get_modes ops are called. Without loss of
> generality, it cannot be assumed that these ops are called when a sink
> gets attached. Therefore there exist scenarios in which the CEC physical
> address will be invalid (f.f.f.f), rendering the CEC adapter inoperable.
>
> Address this problem by always fetching the EDID in the HPD work when we
> detect a connection. The CEC physical address is set in the process.
> This is done by moving the EDID DRM helper into an internal helper
> function so that it can be cleanly called from an earlier section of
> the code. The EDID getter has not changed in practice.
>
> Reviewed-by: Robert Foss <rfoss@xxxxxxxxxx>
> Signed-off-by: Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
> ---
>  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 73 ++++++++++++++++++----------
>  1 file changed, 47 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> index 5ffc5904bd59..d823b372ff43 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> @@ -542,6 +542,36 @@ static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block,
>  	return 0;
>  }
>  
> +static struct edid *__adv7511_get_edid(struct adv7511 *adv7511,
> +				       struct drm_connector *connector)
> +{
> +	struct edid *edid;
> +
> +	/* Reading the EDID only works if the device is powered */
> +	if (!adv7511->powered) {
> +		unsigned int edid_i2c_addr =
> +					(adv7511->i2c_edid->addr << 1);
> +
> +		__adv7511_power_on(adv7511);
> +
> +		/* Reset the EDID_I2C_ADDR register as it might be cleared */
> +		regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
> +			     edid_i2c_addr);
> +	}
> +
> +	edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
> +
> +	if (!adv7511->powered)
> +		__adv7511_power_off(adv7511);
> +
> +	adv7511_set_config_csc(adv7511, connector, adv7511->rgb,
> +			       drm_detect_hdmi_monitor(edid));
> +
> +	cec_s_phys_addr_from_edid(adv7511->cec_adap, edid);

It really would be better to do drm_edid_read_custom(),
drm_edid_connector_update(), and cec_s_phys_addr() with the physical
address from connector->display_info.source_physical_address initialized
by drm_edid_connector_update().

The point is, cec_s_phys_addr_from_edid() has its own duplicate EDID
parsing, which is slightly different from drm_edid_connector_update()
and of course redundant.


BR,
Jani.


> +
> +	return edid;
> +}
> +
>  /* -----------------------------------------------------------------------------
>   * Hotplug handling
>   */
> @@ -595,8 +625,23 @@ static void adv7511_hpd_work(struct work_struct *work)
>  		adv7511->connector.status = status;
>  
>  		if (adv7511->connector.dev) {
> -			if (status == connector_status_disconnected)
> +			if (status == connector_status_disconnected) {
>  				cec_phys_addr_invalidate(adv7511->cec_adap);
> +			} else {
> +				struct edid *edid;
> +
> +				/*
> +				 * Get the updated EDID so that the CEC
> +				 * subsystem gets informed of any change in CEC
> +				 * address. The helper returns a newly allocated
> +				 * edid structure, so free it to prevent
> +				 * leakage.
> +				 */
> +				edid = __adv7511_get_edid(adv7511,
> +							  &adv7511->connector);
> +				kfree(edid);
> +			}
> +
>  			drm_kms_helper_hotplug_event(adv7511->connector.dev);
>  		} else {
>  			drm_bridge_hpd_notify(&adv7511->bridge, status);
> @@ -611,31 +656,7 @@ static void adv7511_hpd_work(struct work_struct *work)
>  static struct edid *adv7511_get_edid(struct adv7511 *adv7511,
>  				     struct drm_connector *connector)
>  {
> -	struct edid *edid;
> -
> -	/* Reading the EDID only works if the device is powered */
> -	if (!adv7511->powered) {
> -		unsigned int edid_i2c_addr =
> -					(adv7511->i2c_edid->addr << 1);
> -
> -		__adv7511_power_on(adv7511);
> -
> -		/* Reset the EDID_I2C_ADDR register as it might be cleared */
> -		regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
> -			     edid_i2c_addr);
> -	}
> -
> -	edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
> -
> -	if (!adv7511->powered)
> -		__adv7511_power_off(adv7511);
> -
> -	adv7511_set_config_csc(adv7511, connector, adv7511->rgb,
> -			       drm_detect_hdmi_monitor(edid));
> -
> -	cec_s_phys_addr_from_edid(adv7511->cec_adap, edid);
> -
> -	return edid;
> +	return __adv7511_get_edid(adv7511, connector);
>  }
>  
>  static int adv7511_get_modes(struct adv7511 *adv7511,

-- 
Jani Nikula, Intel