Re: [PATCH 6/6] arm64: dts: qcom: ipq9574: Add RDP433 board device tree

[Dmitry Baryshkov]

On 10 January 2024 13:20:59 EET, Luo Jie <quic_luoj@xxxxxxxxxxx> wrote:
>From: Lei Wei <quic_leiwei@xxxxxxxxxxx>
>
>RDP433 board has four QCA8075 PHYs and two Aquantia 10G PHY onboard.
>
>Signed-off-by: Lei Wei <quic_leiwei@xxxxxxxxxxx>
>Signed-off-by: Luo Jie <quic_luoj@xxxxxxxxxxx>
>---
> arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 66 +++++++++++++++++++++
> 1 file changed, 66 insertions(+)
>
>diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>index 1bb8d96c9a82..298c0853b4d2 100644
>--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>@@ -60,3 +60,69 @@ rclk-pins {
> 		};
> 	};
> };
>+
>+&qcom_ppe {
>+	qcom,port_phyinfo {
>+		ppe_port0: port@0 {
>+			port_id = <1>;
>+			phy-mode = "qsgmii";
>+			phy-handle = <&phy0>;
>+		};
>+		ppe_port1: port@1 {
>+			port_id = <2>;
>+			phy-mode = "qsgmii";
>+			phy-handle = <&phy1>;
>+		};
>+		ppe_port2: port@2 {
>+			port_id = <3>;
>+			phy-mode = "qsgmii";
>+			phy-handle = <&phy2>;
>+		};
>+		ppe_port3: port@3 {
>+			port_id = <4>;
>+			phy-mode = "qsgmii";
>+			phy-handle = <&phy3>;
>+		};
>+		ppe_port4: port@4 {
>+			port_id = <5>;
>+			phy-mode = "usxgmii";
>+			phy-handle = <&phy4>;
>+		};
>+		ppe_port5: port@5 {
>+			port_id = <6>;
>+			phy-mode = "usxgmii";
>+			phy-handle = <&phy5>;
>+		};
>+	};
>+};
>+
>+&mdio {
>+	reset-gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
>+	status = "okay";
>+
>+	phy0: ethernet-phy@0 {
>+		      reg = <16>;
>+	      };

This part looks extremely wrong to me. If the reg is 16, then it should be @16 as well. You should have got a warning here.

>+
>+	phy1: ethernet-phy@1 {
>+		      reg = <17>;
>+	      };
>+
>+	phy2: ethernet-phy@2 {
>+		      reg = <18>;
>+	      };
>+
>+	phy3: ethernet-phy@3 {
>+		      reg = <19>;
>+	      };
>+
>+	phy4: ethernet-phy@4 {
>+		      compatible ="ethernet-phy-ieee802.3-c45";
>+		      reg = <8>;
>+	      };
>+
>+	phy5: ethernet-phy@5 {
>+		      compatible ="ethernet-phy-ieee802.3-c45";
>+		      reg = <0>;
>+	      };
>+};