Re: [PATCH v2 2/2] Input: add Himax HX852x(ES) touchscreen driver
From: Stephan Gerhold
Date: Sun Oct 22 2023 - 14:49:31 EST
Hi Jeff,
Thanks a lot for reviewing this again!
On Sun, Oct 22, 2023 at 01:23:06PM -0500, Jeff LaBundy wrote:
> Hi Stephan,
>
> This looks great, just a few remaining comments.
>
> On Sat, Sep 30, 2023 at 05:32:01PM +0200, Stephan Gerhold wrote:
> > From: Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx>
> >
> > Add a simple driver for the Himax HX852x(ES) touch panel controller,
> > with support for multi-touch and capacitive touch keys.
> >
> > The driver is somewhat based on sample code from Himax. However, that
> > code was so extremely confusing that we spent a significant amount of
> > time just trying to understand the packet format and register commands.
> > In this driver they are described with clean structs and defines rather
> > than lots of magic numbers and offset calculations.
> >
> > Signed-off-by: Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx>
> > Co-developed-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
> > Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
> > ---
> > MAINTAINERS | 7 +
> > drivers/input/touchscreen/Kconfig | 10 +
> > drivers/input/touchscreen/Makefile | 1 +
> > drivers/input/touchscreen/himax_hx852x.c | 499 +++++++++++++++++++++++++++++++
> > 4 files changed, 517 insertions(+)
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 90f13281d297..c551c60b0598 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -9331,6 +9331,13 @@ S: Maintained
> > F: Documentation/devicetree/bindings/input/touchscreen/himax,hx83112b.yaml
> > F: drivers/input/touchscreen/himax_hx83112b.c
> >
> > +HIMAX HX852X TOUCHSCREEN DRIVER
> > +M: Stephan Gerhold <stephan@xxxxxxxxxxx>
> > +L: linux-input@xxxxxxxxxxxxxxx
> > +S: Maintained
> > +F: Documentation/devicetree/bindings/input/touchscreen/himax,hx852es.yaml
> > +F: drivers/input/touchscreen/himax_hx852x.c
> > +
> > HIPPI
> > M: Jes Sorensen <jes@xxxxxxxxxxxxxxxxxx>
> > L: linux-hippi@xxxxxxxxxx
> > diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> > index e3e2324547b9..8e5667ae5dab 100644
> > --- a/drivers/input/touchscreen/Kconfig
> > +++ b/drivers/input/touchscreen/Kconfig
> > @@ -427,6 +427,16 @@ config TOUCHSCREEN_HIDEEP
> > To compile this driver as a module, choose M here : the
> > module will be called hideep_ts.
> >
> > +config TOUCHSCREEN_HIMAX_HX852X
> > + tristate "Himax HX852x(ES) touchscreen"
> > + depends on I2C
> > + help
> > + Say Y here if you have a Himax HX852x(ES) touchscreen.
> > + If unsure, say N.
> > +
> > + To compile this driver as a module, choose M here: the module
> > + will be called himax_hx852x.
> > +
> > config TOUCHSCREEN_HYCON_HY46XX
> > tristate "Hycon hy46xx touchscreen support"
> > depends on I2C
> > diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
> > index 62bd24f3ac8e..f42a87faa86c 100644
> > --- a/drivers/input/touchscreen/Makefile
> > +++ b/drivers/input/touchscreen/Makefile
> > @@ -48,6 +48,7 @@ obj-$(CONFIG_TOUCHSCREEN_EXC3000) += exc3000.o
> > obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
> > obj-$(CONFIG_TOUCHSCREEN_GOODIX) += goodix_ts.o
> > obj-$(CONFIG_TOUCHSCREEN_HIDEEP) += hideep.o
> > +obj-$(CONFIG_TOUCHSCREEN_HIMAX_HX852X) += himax_hx852x.o
> > obj-$(CONFIG_TOUCHSCREEN_HYNITRON_CSTXXX) += hynitron_cstxxx.o
> > obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
> > obj-$(CONFIG_TOUCHSCREEN_ILITEK) += ilitek_ts_i2c.o
> > diff --git a/drivers/input/touchscreen/himax_hx852x.c b/drivers/input/touchscreen/himax_hx852x.c
> > new file mode 100644
> > index 000000000000..98a55be7891d
> > --- /dev/null
> > +++ b/drivers/input/touchscreen/himax_hx852x.c
> > @@ -0,0 +1,499 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Himax HX852x(ES) Touchscreen Driver
> > + * Copyright (c) 2020-2023 Stephan Gerhold <stephan@xxxxxxxxxxx>
> > + * Copyright (c) 2020 Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx>
> > + *
> > + * Based on the Himax Android Driver Sample Code Ver 0.3 for HMX852xES chipset:
> > + * Copyright (c) 2014 Himax Corporation.
> > + */
> > +
> > +#include <asm/unaligned.h>
> > +#include <linux/delay.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/i2c.h>
> > +#include <linux/input.h>
> > +#include <linux/input/mt.h>
> > +#include <linux/input/touchscreen.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#define HX852X_COORD_SIZE(fingers) ((fingers) * sizeof(struct hx852x_coord))
> > +#define HX852X_WIDTH_SIZE(fingers) ALIGN(fingers, 4)
> > +#define HX852X_BUF_SIZE(fingers) (HX852X_COORD_SIZE(fingers) + \
> > + HX852X_WIDTH_SIZE(fingers) + \
> > + sizeof(struct hx852x_touch_info))
> > +
> > +#define HX852X_MAX_FINGERS 12
> > +#define HX852X_MAX_KEY_COUNT 4
> > +#define HX852X_MAX_BUF_SIZE HX852X_BUF_SIZE(HX852X_MAX_FINGERS)
> > +
> > +#define HX852X_TS_SLEEP_IN 0x80
> > +#define HX852X_TS_SLEEP_OUT 0x81
> > +#define HX852X_TS_SENSE_OFF 0x82
> > +#define HX852X_TS_SENSE_ON 0x83
> > +#define HX852X_READ_ONE_EVENT 0x85
> > +#define HX852X_READ_ALL_EVENTS 0x86
> > +#define HX852X_READ_LATEST_EVENT 0x87
> > +#define HX852X_CLEAR_EVENT_STACK 0x88
> > +
> > +#define HX852X_REG_SRAM_SWITCH 0x8c
> > +#define HX852X_REG_SRAM_ADDR 0x8b
> > +#define HX852X_REG_FLASH_RPLACE 0x5a
> > +
> > +#define HX852X_SRAM_SWITCH_TEST_MODE 0x14
> > +#define HX852X_SRAM_ADDR_CONFIG 0x7000
> > +
> > +struct hx852x {
> > + struct i2c_client *client;
> > + struct input_dev *input_dev;
> > + struct touchscreen_properties props;
> > + struct gpio_desc *reset_gpiod;
> > + struct regulator_bulk_data supplies[2];
> > + unsigned int max_fingers;
> > + unsigned int keycount;
> > + unsigned int keycodes[HX852X_MAX_KEY_COUNT];
> > +};
> > +
> > +struct hx852x_config {
> > + u8 rx_num;
> > + u8 tx_num;
> > + u8 max_pt;
> > + u8 padding1[3];
> > + __be16 x_res;
> > + __be16 y_res;
> > + u8 padding2[2];
> > +} __packed __aligned(4);
> > +
> > +struct hx852x_coord {
> > + __be16 x;
> > + __be16 y;
> > +} __packed __aligned(4);
> > +
> > +struct hx852x_touch_info {
> > + u8 finger_num;
> > + __le16 finger_pressed;
> > + u8 padding;
> > +} __packed __aligned(4);
> > +
> > +static int hx852x_i2c_read(struct hx852x *hx, u8 cmd, void *data, u16 len)
> > +{
> > + struct i2c_client *client = hx->client;
> > + int ret;
> > +
> > + struct i2c_msg msg[] = {
> > + {
> > + .addr = client->addr,
> > + .flags = 0,
> > + .len = 1,
> > + .buf = &cmd,
> > + },
> > + {
> > + .addr = client->addr,
> > + .flags = I2C_M_RD,
> > + .len = len,
> > + .buf = data,
> > + }
>
> Nit: standard practice is to close all array elements with a trailing comma,
> even the final element, in order to avoid an extra line in the diff (i.e.
> } --> },) if another element is added later. Obviously we wouldn't add more
> elements to this array in the future, but it's best to remain consistent.
>
Sure, I'll fix this in v3!
> > + };
> > +
> > + ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
> > + if (ret != ARRAY_SIZE(msg)) {
> > + dev_err(&client->dev, "failed to read %#x: %d\n", cmd, ret);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int hx852x_power_on(struct hx852x *hx)
> > +{
> > + struct device *dev = &hx->client->dev;
> > + int error;
> > +
> > + error = regulator_bulk_enable(ARRAY_SIZE(hx->supplies), hx->supplies);
> > + if (error) {
> > + dev_err(dev, "failed to enable regulators: %d\n", error);
> > + return error;
> > + }
> > +
> > + gpiod_set_value_cansleep(hx->reset_gpiod, 1);
> > + msleep(20);
> > + gpiod_set_value_cansleep(hx->reset_gpiod, 0);
> > + msleep(20);
> > +
> > + return 0;
> > +}
> > +
> > +static int hx852x_start(struct hx852x *hx)
> > +{
> > + struct device *dev = &hx->client->dev;
> > + int error;
> > +
> > + error = i2c_smbus_write_byte(hx->client, HX852X_TS_SLEEP_OUT);
> > + if (error) {
> > + dev_err(dev, "failed to send TS_SLEEP_OUT: %d\n", error);
> > + return error;
> > + }
> > + msleep(30);
> > +
> > + error = i2c_smbus_write_byte(hx->client, HX852X_TS_SENSE_ON);
> > + if (error) {
> > + dev_err(dev, "failed to send TS_SENSE_ON: %d\n", error);
> > + return error;
> > + }
> > + msleep(20);
> > +
> > + return 0;
> > +}
> > +
> > +static int hx852x_stop(struct hx852x *hx)
> > +{
> > + struct device *dev = &hx->client->dev;
> > + int error;
> > +
> > + error = i2c_smbus_write_byte(hx->client, HX852X_TS_SENSE_OFF);
> > + if (error) {
> > + dev_err(dev, "failed to send TS_SENSE_OFF: %d\n", error);
> > + return error;
> > + }
> > + msleep(20);
> > +
> > + error = i2c_smbus_write_byte(hx->client, HX852X_TS_SLEEP_IN);
> > + if (error) {
> > + dev_err(dev, "failed to send TS_SLEEP_IN: %d\n", error);
> > + return error;
> > + }
> > + msleep(30);
> > +
> > + return 0;
> > +}
> > +
> > +static int hx852x_power_off(struct hx852x *hx)
> > +{
> > + struct device *dev = &hx->client->dev;
> > + int error;
> > +
> > + error = regulator_bulk_disable(ARRAY_SIZE(hx->supplies), hx->supplies);
> > + if (error)
> > + dev_err(dev, "failed to disable regulators: %d\n", error);
> > + return error;
> > +}
> > +
> > +static int hx852x_read_config(struct hx852x *hx)
> > +{
> > + struct device *dev = &hx->client->dev;
> > + struct hx852x_config conf;
> > + int x_res, y_res;
> > + int error;
> > +
> > + error = hx852x_power_on(hx);
> > + if (error)
> > + return error;
> > +
> > + /* Sensing must be turned on briefly to load the config */
> > + error = hx852x_start(hx);
> > + if (error)
> > + goto err_power_off;
> > +
> > + error = hx852x_stop(hx);
> > + if (error)
> > + goto err_power_off;
> > +
> > + error = i2c_smbus_write_byte_data(hx->client, HX852X_REG_SRAM_SWITCH,
> > + HX852X_SRAM_SWITCH_TEST_MODE);
> > + if (error)
> > + goto err_power_off;
> > +
> > + error = i2c_smbus_write_word_data(hx->client, HX852X_REG_SRAM_ADDR,
> > + HX852X_SRAM_ADDR_CONFIG);
> > + if (error)
> > + goto err_test_mode;
> > +
> > + error = hx852x_i2c_read(hx, HX852X_REG_FLASH_RPLACE, &conf, sizeof(conf));
> > + if (error)
> > + goto err_test_mode;
> > +
> > + x_res = be16_to_cpu(conf.x_res);
> > + y_res = be16_to_cpu(conf.y_res);
> > + hx->max_fingers = (conf.max_pt & 0xf0) >> 4;
> > + dev_dbg(dev, "x res: %u, y res: %u, max fingers: %u\n",
> > + x_res, y_res, hx->max_fingers);
> > +
> > + if (hx->max_fingers > HX852X_MAX_FINGERS) {
> > + dev_err(dev, "max supported fingers: %u, found: %u\n",
> > + HX852X_MAX_FINGERS, hx->max_fingers);
> > + error = -EINVAL;
> > + goto err_test_mode;
> > + }
> > +
> > + if (x_res && y_res) {
> > + input_set_abs_params(hx->input_dev, ABS_MT_POSITION_X, 0, x_res - 1, 0, 0);
> > + input_set_abs_params(hx->input_dev, ABS_MT_POSITION_Y, 0, y_res - 1, 0, 0);
> > + }
> > +
> > + error = i2c_smbus_write_byte_data(hx->client, HX852X_REG_SRAM_SWITCH, 0);
> > + if (error)
> > + goto err_power_off;
> > +
> > + return hx852x_power_off(hx);
> > +
> > +err_test_mode:
> > + i2c_smbus_write_byte_data(hx->client, HX852X_REG_SRAM_SWITCH, 0);
> > +err_power_off:
> > + hx852x_power_off(hx);
> > + return error;
>
> Your new version is an improvement, but maybe we can remove duplicate
> code by introducing some helper variables:
>
> int error, error2 = 0, error3;
>
> /* ... */
>
> err_test_mode:
> error2 = i2c_smbus_write_byte_data(...);
>
> err_power_off:
> error3 = hx852x_power_off(...);
>
> if (error)
> return error;
>
> return error2 ? : error3;
>
> In this case we achieve our goal of attempting to return the device to a
> safe state in both passing and failing cases. In the event of multiple
> errors, we return the first to occur.
>
Right, this would work as well. Personally I think my solution is
slightly easier to read though. In your version my eyes somewhat
"stumble" over the multiple "error" variables and then about the purpose
of the "? : " construction. This is probably highly subjective. :-)
Do you mind if keep this as-is? I don't have a strong opinion about
this, but a slight preference for my current solution.
> > +}
> > +
> > +static int hx852x_handle_events(struct hx852x *hx)
> > +{
> > + /*
> > + * The event packets have variable size, depending on the amount of
> > + * supported fingers (hx->max_fingers). They are laid out as follows:
> > + * - struct hx852x_coord[hx->max_fingers]: Coordinates for each finger
> > + * - u8[ALIGN(hx->max_fingers, 4)]: Touch width for each finger
> > + * with padding for 32-bit alignment
> > + * - struct hx852x_touch_info
> > + *
> > + * Load everything into a 32-bit aligned buffer so the coordinates
> > + * can be assigned directly, without using get_unaligned_*().
> > + */
> > + u8 buf[HX852X_MAX_BUF_SIZE] __aligned(4);
> > + struct hx852x_coord *coord = (struct hx852x_coord *)buf;
> > + u8 *width = &buf[HX852X_COORD_SIZE(hx->max_fingers)];
> > + struct hx852x_touch_info *info = (struct hx852x_touch_info *)
> > + &width[HX852X_WIDTH_SIZE(hx->max_fingers)];
> > + unsigned long finger_pressed, key_pressed;
> > + unsigned int i, x, y, w;
> > + int error;
> > +
> > + error = hx852x_i2c_read(hx, HX852X_READ_ALL_EVENTS, buf,
> > + HX852X_BUF_SIZE(hx->max_fingers));
> > + if (error)
> > + return error;
> > +
> > + finger_pressed = get_unaligned_le16(&info->finger_pressed);
> > + key_pressed = finger_pressed >> HX852X_MAX_FINGERS;
> > +
> > + /* All bits are set when no touch is detected */
> > + if (info->finger_num == 0xff || !(info->finger_num & 0x0f))
> > + finger_pressed = 0;
> > + if (key_pressed == 0xf)
> > + key_pressed = 0;
> > +
> > + for_each_set_bit(i, &finger_pressed, hx->max_fingers) {
> > + x = be16_to_cpu(coord[i].x);
> > + y = be16_to_cpu(coord[i].y);
> > + w = width[i];
> > +
> > + input_mt_slot(hx->input_dev, i);
> > + input_mt_report_slot_state(hx->input_dev, MT_TOOL_FINGER, 1);
> > + touchscreen_report_pos(hx->input_dev, &hx->props, x, y, true);
> > + input_report_abs(hx->input_dev, ABS_MT_TOUCH_MAJOR, w);
> > + }
> > + input_mt_sync_frame(hx->input_dev);
> > +
> > + for (i = 0; i < hx->keycount; i++)
> > + input_report_key(hx->input_dev, hx->keycodes[i], key_pressed & BIT(i));
> > +
> > + input_sync(hx->input_dev);
> > + return 0;
> > +}
> > +
> > +static irqreturn_t hx852x_interrupt(int irq, void *ptr)
> > +{
> > + struct hx852x *hx = ptr;
> > + int error;
> > +
> > + error = hx852x_handle_events(hx);
> > + if (error) {
> > + dev_err_ratelimited(&hx->client->dev, "failed to handle events: %d\n", error);
> > + return IRQ_NONE;
> > + }
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int hx852x_input_open(struct input_dev *dev)
> > +{
> > + struct hx852x *hx = input_get_drvdata(dev);
> > + int error;
> > +
> > + error = hx852x_power_on(hx);
> > + if (error)
> > + return error;
> > +
> > + error = hx852x_start(hx);
> > + if (error) {
> > + hx852x_power_off(hx);
> > + return error;
> > + }
> > +
> > + enable_irq(hx->client->irq);
> > + return 0;
> > +}
> > +
> > +static void hx852x_input_close(struct input_dev *dev)
> > +{
> > + struct hx852x *hx = input_get_drvdata(dev);
> > +
> > + hx852x_stop(hx);
> > + disable_irq(hx->client->irq);
> > + hx852x_power_off(hx);
> > +}
> > +
> > +static int hx852x_parse_properties(struct hx852x *hx)
> > +{
> > + struct device *dev = &hx->client->dev;
> > + int error;
> > +
> > + hx->keycount = device_property_count_u32(dev, "linux,keycodes");
> > + if (hx->keycount <= 0) {
> > + hx->keycount = 0;
> > + return 0;
> > + }
>
> With negative return values of device_property_count_u32() squashed in this
> way, there is no way to warn the developer that the array is invalid. The
> error message associated with device_property_read_u32_array() below is
> essentially dead code, because the latter is a wrapper around the former,
> and any syntax error that causes one to fail will cause the other to fail.
>
> Since device_property_count_u32() returns -EINVAL in case of a missing array,
> we can do the following. Note there is no need to explicitly set hx->keycount
> to zero in case no keys are specified, since the hx structure is correctly
> allocated using devm_kzalloc().
>
> int count;
>
> count = device_property_count_u32(...);
> if (count == -EINVAL) {
> return 0;
> } else if (count < 0) {
> dev_err(...);
> return count;
> } else if (count > HX852X_MAX_KEY_COUNT) {
> dev_err(...);
> return -EINVAL;
> }
>
> hx->keycount = count;
>
> error = device_property_read_u32_array(...);
> if (error)
> dev_err(...);
>
> return error;
>
Ah right, thanks for spotting this! Will use this in v3.
> > +
> > + if (hx->keycount > HX852X_MAX_KEY_COUNT) {
> > + dev_err(dev, "max supported keys: %u, found: %u\n",
> > + HX852X_MAX_KEY_COUNT, hx->keycount);
> > + return -EINVAL;
> > + }
> > +
> > + error = device_property_read_u32_array(dev, "linux,keycodes",
> > + hx->keycodes, hx->keycount);
> > + if (error)
> > + dev_err(dev, "failed to read linux,keycodes: %d\n", error);
> > +
> > + return error;
> > +}
> > +
> > +static int hx852x_probe(struct i2c_client *client)
> > +{
> > + struct device *dev = &client->dev;
> > + struct hx852x *hx;
> > + int error, i;
> > +
> > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
> > + I2C_FUNC_SMBUS_WRITE_BYTE |
> > + I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
> > + I2C_FUNC_SMBUS_WRITE_WORD_DATA)) {
> > + dev_err(dev, "not all required i2c functionality supported\n");
> > + return -ENXIO;
> > + }
> > +
> > + hx = devm_kzalloc(dev, sizeof(*hx), GFP_KERNEL);
> > + if (!hx)
> > + return -ENOMEM;
> > +
> > + hx->client = client;
> > + hx->input_dev = devm_input_allocate_device(dev);
> > + if (!hx->input_dev)
> > + return -ENOMEM;
> > +
> > + hx->input_dev->name = "Himax HX852x";
> > + hx->input_dev->id.bustype = BUS_I2C;
> > + hx->input_dev->open = hx852x_input_open;
> > + hx->input_dev->close = hx852x_input_close;
> > +
> > + i2c_set_clientdata(client, hx);
> > + input_set_drvdata(hx->input_dev, hx);
> > +
> > + hx->supplies[0].supply = "vcca";
> > + hx->supplies[1].supply = "vccd";
> > + error = devm_regulator_bulk_get(dev, ARRAY_SIZE(hx->supplies), hx->supplies);
> > + if (error)
> > + return dev_err_probe(dev, error, "failed to get regulators\n");
> > +
> > + hx->reset_gpiod = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> > + if (IS_ERR(hx->reset_gpiod))
> > + return dev_err_probe(dev, PTR_ERR(hx->reset_gpiod),
> > + "failed to get reset gpio\n");
> > +
> > + error = devm_request_threaded_irq(dev, client->irq, NULL, hx852x_interrupt,
> > + IRQF_ONESHOT | IRQF_NO_AUTOEN, NULL, hx);
> > + if (error)
> > + return dev_err_probe(dev, error, "failed to request irq %d", client->irq);
> > +
> > + error = hx852x_read_config(hx);
> > + if (error)
> > + return error;
> > +
> > + input_set_capability(hx->input_dev, EV_ABS, ABS_MT_POSITION_X);
> > + input_set_capability(hx->input_dev, EV_ABS, ABS_MT_POSITION_Y);
> > + input_set_abs_params(hx->input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
> > +
> > + touchscreen_parse_properties(hx->input_dev, true, &hx->props);
> > + error = hx852x_parse_properties(hx);
> > + if (error)
> > + return error;
> > +
> > + hx->input_dev->keycode = hx->keycodes;
> > + hx->input_dev->keycodemax = hx->keycount;
> > + hx->input_dev->keycodesize = sizeof(hx->keycodes[0]);
> > + for (i = 0; i < hx->keycount; i++)
> > + input_set_capability(hx->input_dev, EV_KEY, hx->keycodes[i]);
> > +
> > + error = input_mt_init_slots(hx->input_dev, hx->max_fingers,
> > + INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
> > + if (error)
> > + return dev_err_probe(dev, error, "failed to init MT slots\n");
> > +
> > + error = input_register_device(hx->input_dev);
> > + if (error)
> > + return dev_err_probe(dev, error, "failed to register input device\n");
> > +
> > + return 0;
> > +}
> > +
> > +static int hx852x_suspend(struct device *dev)
> > +{
> > + struct hx852x *hx = dev_get_drvdata(dev);
>
> int error = 0;
>
> > +
> > + mutex_lock(&hx->input_dev->mutex);
> > + if (input_device_enabled(hx->input_dev))
> > + hx852x_stop(hx);
>
> error = hx852x_stop(...);
>
> > + mutex_unlock(&hx->input_dev->mutex);
> > +
> > + return 0;
>
> return error;
>
Oops. I meant to change this in v2 but forgot it apparently.
Will fix fix this in v3 as well!
I'll wait for your reply regarding the error handling in
hx852x_read_config(), in case you have a strong opinion about that. :)
Thanks!
Stephan