PROBLEM: SCSI failure resulting in kernel panic

From: Wilfried v. Hulzen
Date: Mon May 17 2004 - 15:56:11 EST

Next message: Andrew Morton: "Re: [PATCH] Quota fix 3 - quota file corruption"
Previous message: Bill Davidsen: "Re: 2.6.6-mm2"
Next in thread: Marcelo Tosatti: "Re: PROBLEM: SCSI failure resulting in kernel panic"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

[1.] SCSI failure resulting in kernel panic
[2.] Full description of the problem/report:
When executing a disc-intensive command:
( cd /var/tmp/. ; tar -cf - . ) | tar -xvf -
in a newly formatted partition on a scsi disc, where /var/tmp. resides on
a IDE disc partition, results almost immediately in the following panic
screen. Note: /var/tmp/. are on /dev/hda5, target partition is /dev/sdb1
Extract from boot information:
hda: Maxtor 6Y160L0, ATA DISK drive
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
sdb:
(scsi0:A:3): 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020W
Type: Direct-Access ANSI SCSI revision: 03

============================================================================
scsi0:A:3:0: Target did not send an IDENTITY message. LASTPHASE = 0xe0.
scsi0:A:3:0: Protocol violation in Message-in phase. Attempting to abort.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Printing eip:
c0232ed0
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c0232ed0>] Not tainted
EFLAGS: 00010046
eax: 00000001 ebx: 00000007 ecx: 00000001 edx: 0000000d
esi: dfe2e800 edi: 00000000 ebp: 000000a0 esp: c03abe88
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 0, stackpage=c03ab000)
Stack: dfe2e800 00000000 0000000d 00000001 00000041 00000001 dfe130b8 def13618
000000ff 00000041 00000003 00000000 00000000 dfe13000 41410330 00000007
00000003 dfe10008 00000003 00000000 00000241 00000001 dfe26e80 00000001
Call Trace: [<c0217b68>] [<c02307fb>] [<0c22f2d6>] [<c022ced9>] [<c0108fc9>]
[<c01091e8>] [<c01053d0>] [<c010bba8>] [<c01053d0>] [<c01053f9>] [<c0105492>]
[<c0105000>]

Code: 8b 07 0f b6 40 1b 89 44 24 20 e9 77 ff ff ff 89 34 24 31 c0
<0>Kernel panic: Aiee, killing interrupt handler!
In interrupt handler - not syncing
_
^^==========================================================================
^^intentional space and cursor as on screen

Output from dmesg on newly booted system follows.
Note: the usb messages near the end originate from a USB CF-card
reader connected to the system.
============================================================================
twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 AMI ) @ 0x000fa120
ACPI: RSDT (v001 AMIINT SiS645XX 0x00000010 MSFT 0x0100000b) @ 0x1fff0000
ACPI: FADT (v001 AMIINT SiS645XX 0x00000011 MSFT 0x0100000b) @ 0x1fff0030
ACPI: MADT (v001 AMIINT SiS645XX 0x00001000 MSFT 0x0100000b) @ 0x1fff00c0
ACPI: DSDT (v001 SiS 645 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: SiS Product ID: 645 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=Linux2.4.26 ro root=301 ramdisk=0 hdc=ide-scsi hdd=ide-scsi acpismp=force
ide_setup: hdc=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 2810.053 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5609.88 BogoMIPS
Memory: 515020k/524224k available (2051k kernel code, 8816k reserved, 673k data, 100k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 07
per-CPU timeslice cutoff: 1462.78 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
..changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-10, 2-11 not connected.
.TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 25.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
... register #00: 02000000
...... : physical APIC id: 02
...... : Delivery Type: 0
...... : LTS : 0
... register #01: 00178011
...... : max redirection entries: 0017
...... : PRQ implemented: 1
...... : IO APIC version: 0011
... register #02: 02000000
...... : arbitration: 02
... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 79
0d 001 01 0 0 0 0 0 1 1 81
0e 001 01 0 0 0 0 0 1 1 89
0f 001 01 0 0 0 0 0 1 1 91
10 001 01 1 1 0 1 0 1 1 99
11 001 01 1 1 0 1 0 1 1 A1
12 001 01 1 1 0 1 0 1 1 A9
13 001 01 1 1 0 1 0 1 1 B1
14 001 01 1 1 0 1 0 1 1 B9
15 001 01 1 1 0 1 0 1 1 C1
16 001 01 1 1 0 1 0 1 1 C9
17 001 01 1 1 0 1 0 1 1 D1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
.... CPU clock speed is 2810.0706 MHz.
.... host bus clock speed is 133.8126 MHz.
cpu: 0, clocks: 1338126, slice: 669063
CPU0<T0:1338112,T1:669040,D:9,S:669063,C:1338126>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS96x [1039/0008] at 00:02.0
PCI->APIC IRQ transform: (B0,I2,P2) -> 18
PCI->APIC IRQ transform: (B0,I3,P0) -> 20
PCI->APIC IRQ transform: (B0,I3,P1) -> 21
PCI->APIC IRQ transform: (B0,I3,P2) -> 22
PCI->APIC IRQ transform: (B0,I3,P3) -> 23
PCI->APIC IRQ transform: (B0,I4,P0) -> 19
PCI->APIC IRQ transform: (B0,I6,P0) -> 17
PCI->APIC IRQ transform: (B0,I8,P0) -> 19
PCI->APIC IRQ transform: (B0,I9,P0) -> 16
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y160L0, ATA DISK drive
hdb: ST320014A, ATA DISK drive
blk: queue c0401f80, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c04020c8, I/O limit 4095Mb (mask 0xffffffff)
hdc: MATSHITADVD-ROM SR-8588, ATAPI CD/DVD-ROM drive
hdd: MATSHITADVD-RAM SW-9581, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 320173056 sectors (163929 MB) w/2048KiB Cache, CHS=19929/255/63, UDMA(133)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(100)
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 >
hdb: hdb1
SCSI subsystem driver Revision: 1.00
Loading Adaptec I2O RAID: Version 2.4 Build 5
Detecting Adaptec I2O RAID controllers...
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs

(scsi0:A:1): 40.000MB/s transfers (20.000MHz, offset 31, 16bit)
Vendor: QUANTUM Model: ATLAS 10K 9WLS Rev: UCH0
Type: Direct-Access ANSI SCSI revision: 03
(scsi0:A:3): 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020W
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled. Depth 8
scsi0:A:3:0: Tagged Queuing enabled. Depth 8
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 3, lun 0
SCSI device sda: 17938986 512-byte hdwr sectors (9185 MB)
sda: sda1 sda2
SCSI device sdb: 35916548 512-byte hdwr sectors (18389 MB)
sdb: sdb1
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 100k freed
Adding Swap: 506036k swap-space (priority 3)
Adding Swap: 250856k swap-space (priority 5)
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device sd(8,2)) ...
for (sd(8,2))
sd(8,2):Using r5 hash to sort names
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device sd(8,17)) ...
for (sd(8,17))
sd(8,17):Using r5 hash to sort names
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected SiS 645 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
hdc: attached ide-scsi driver.
hdd: attached ide-scsi driver.
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: DVD-ROM SR-8588 Rev: 7Z14
Type: CD-ROM ANSI SCSI revision: 02
Vendor: MATSHITA Model: DVD-RAM SW-9581 Rev: B100
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
sis900.c: v1.08.06 9/24/2002
eth0: Unknown PHY transceiver found at address 0.
eth0: Realtek RTL8201 PHY transceiver found at address 1.
eth0: Unknown PHY transceiver found at address 2.
eth0: Unknown PHY transceiver found at address 3.
eth0: Unknown PHY transceiver found at address 4.
eth0: Unknown PHY transceiver found at address 5.
eth0: Unknown PHY transceiver found at address 6.
eth0: Unknown PHY transceiver found at address 7.
eth0: Unknown PHY transceiver found at address 8.
eth0: Unknown PHY transceiver found at address 9.
eth0: Unknown PHY transceiver found at address 10.
eth0: Unknown PHY transceiver found at address 11.
eth0: Unknown PHY transceiver found at address 12.
eth0: Unknown PHY transceiver found at address 13.
eth0: Unknown PHY transceiver found at address 14.
eth0: Unknown PHY transceiver found at address 15.
eth0: Unknown PHY transceiver found at address 16.
eth0: Unknown PHY transceiver found at address 17.
eth0: Unknown PHY transceiver found at address 18.
eth0: Unknown PHY transceiver found at address 19.
eth0: Unknown PHY transceiver found at address 20.
eth0: Unknown PHY transceiver found at address 21.
eth0: Unknown PHY transceiver found at address 22.
eth0: Unknown PHY transceiver found at address 23.
eth0: Unknown PHY transceiver found at address 24.
eth0: Unknown PHY transceiver found at address 25.
eth0: Unknown PHY transceiver found at address 26.
eth0: Unknown PHY transceiver found at address 27.
eth0: Unknown PHY transceiver found at address 28.
eth0: Unknown PHY transceiver found at address 29.
eth0: Unknown PHY transceiver found at address 30.
eth0: Unknown PHY transceiver found at address 31.
eth0: Using transceiver found at address 31 as default
eth0: SiS 900 PCI Fast Ethernet at 0xd000, IRQ 19, 00:10:dc:ca:e2:39.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xe0a0e000, IRQ 22
usb-ohci.c: usb-00:03.2, Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-ohci.c: USB OHCI at membase 0xe0a10000, IRQ 21
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-ohci.c: USB OHCI at membase 0xe0a12000, IRQ 20
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: new USB device 00:03.0-2, assigned address 2
usb.c: USB device 2 (vend/prod 0xdda/0x2001) is not claimed by any active driver.
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-uhci.c: $Revision: 1.275 $ time 14:44:07 May 14 2004
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: ICSI Model: CF Card CF Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Vendor: ICSI Model: MS Card MS Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Vendor: ICSI Model: SD Card MMC/SD Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Vendor: ICSI Model: SM Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 0
Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 1
Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 2
Attached scsi removable disk sdf at scsi2, channel 0, id 0, lun 3
SCSI device sdc: 511056 512-byte hdwr sectors (262 MB)
sdc: Write Protect is off
sdc: sdc1
sdd: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sense key Not Ready
Additional sense indicates Medium not present
sdd : READ CAPACITY failed.
sdd : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sdd : block size assumed to be 512 bytes, disk size 1GB.
sdd: I/O error: dev 08:30, sector 0
I/O error: dev 08:30, sector 0
unable to read partition table
sde: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sense key Not Ready
Additional sense indicates Medium not present
sde : READ CAPACITY failed.
sde : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sde : block size assumed to be 512 bytes, disk size 1GB.
sde: I/O error: dev 08:40, sector 0
I/O error: dev 08:40, sector 0
unable to read partition table
sdf: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sense key Not Ready
Additional sense indicates Medium not present
sdf : READ CAPACITY failed.
sdf : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sdf : block size assumed to be 512 bytes, disk size 1GB.
sdf: I/O error: dev 08:50, sector 0
I/O error: dev 08:50, sector 0
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
============================================================================
[3.] Keywords (i.e., modules, networking, kernel):
Kernel compiled using the following config options file:
#
# Automatically generated by make menuconfig: don't edit
#
CONFIG_X86=y
# CONFIG_SBUS is not set
CONFIG_UID16=y

#
# Code maturity level options
#
# CONFIG_EXPERIMENTAL is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y

#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_HAS_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_F00F_WORKS_OK=y
# CONFIG_X86_MCE is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_HIGHMEM is not set
CONFIG_MATH_EMULATION=y
CONFIG_MTRR=y
CONFIG_SMP=y
CONFIG_NR_CPUS=4
# CONFIG_X86_NUMA is not set
# CONFIG_X86_TSC_DISABLE is not set
CONFIG_X86_TSC=y
CONFIG_HAVE_DEC_LOCK=y

#
# General setup
#
CONFIG_NET=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y

#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
# CONFIG_OOM_KILLER is not set
CONFIG_PM=y
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
CONFIG_APM_RTC_IS_GMT=y
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# ACPI Support
#
# CONFIG_ACPI is not set
CONFIG_ACPI_BOOT=y

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
CONFIG_PARPORT_SERIAL=m
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
# CONFIG_PARPORT_IP22 is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play configuration
#
CONFIG_PNP=m
CONFIG_ISAPNP=m

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_CISS_MONITOR_THREAD is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_BLK_STATS is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_NETLINK_DEV=m
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_INET_ECN=y
CONFIG_SYN_COOKIES=y

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_NAT_AMANDA=m
# CONFIG_IP_NF_NAT_LOCAL is not set
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_IP_NF_COMPAT_IPCHAINS=m
CONFIG_IP_NF_NAT_NEEDED=y
# CONFIG_IP_NF_COMPAT_IPFWADM is not set

#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m
CONFIG_IP_VS_FTP=m
# CONFIG_VLAN_8021Q is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set

#
# Appletalk devices
#
# CONFIG_DEV_APPLETALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_CSZ=m
# CONFIG_NET_SCH_HFSC is not set
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
# CONFIG_NET_SCH_DELAY is not set
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_INGRESS=m
# CONFIG_NET_QOS is not set
# CONFIG_NET_CLS is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set

#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y

#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIIMAGE=m
CONFIG_BLK_DEV_SIS5513=y
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_MEDLEY is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set

#
# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_DEBUG_QUEUES=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC79XX=y
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=15000
# CONFIG_AIC79XX_BUILD_FIRMWARE is not set
# CONFIG_AIC79XX_ENABLE_RD_STRM is not set
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_DPT_I2O=y
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_MEGARAID2 is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set

#
# I2O device support
#
CONFIG_I2O=m
CONFIG_I2O_PCI=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_LAN=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m

#
# Network device support
#
CONFIG_NETDEVICES=y

#
# ARCnet devices
#
CONFIG_ARCNET=m
CONFIG_ARCNET_1201=m
CONFIG_ARCNET_1051=m
CONFIG_ARCNET_RAW=m
CONFIG_ARCNET_COM90xx=m
CONFIG_ARCNET_COM90xxIO=m
CONFIG_ARCNET_RIM_I=m
CONFIG_ARCNET_COM20020=m
CONFIG_ARCNET_COM20020_ISA=m
CONFIG_ARCNET_COM20020_PCI=m
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
CONFIG_NET_SB1000=m

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_CS89x0 is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
# CONFIG_EEPRO100 is not set
# CONFIG_EEPRO100_PIO is not set
# CONFIG_E100 is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_FORCEDETH is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
CONFIG_8139TOO_TUNE_TWISTER=y
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_SUNDANCE_MMIO is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
CONFIG_PLIP=m
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set

#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set

#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set

#
# ISDN subsystem
#
CONFIG_ISDN=m
CONFIG_ISDN_BOOL=y
CONFIG_ISDN_PPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
# CONFIG_ISDN_X25 is not set

#
# ISDN feature submodules
#
CONFIG_ISDN_DRV_LOOP=m
CONFIG_ISDN_DIVERSION=m

#
# Passive ISDN cards
#
CONFIG_ISDN_DRV_HISAX=m
CONFIG_ISDN_HISAX=y
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
# CONFIG_HISAX_NI1 is not set
CONFIG_HISAX_MAX_CARDS=8
CONFIG_HISAX_16_0=y
CONFIG_HISAX_16_3=y
CONFIG_HISAX_AVM_A1=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_ASUSCOM=y
CONFIG_HISAX_TELEINT=y
CONFIG_HISAX_HFCS=y
CONFIG_HISAX_SPORTSTER=y
CONFIG_HISAX_MIC=y
CONFIG_HISAX_ISURF=y
CONFIG_HISAX_HSTSAPHIR=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_SEDLBAUER=y
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
# CONFIG_HISAX_DEBUG is not set
# CONFIG_HISAX_SEDLBAUER_CS is not set
# CONFIG_HISAX_ELSA_CS is not set
# CONFIG_HISAX_AVM_A1_CS is not set
# CONFIG_HISAX_ST5481 is not set
# CONFIG_HISAX_FRITZ_PCIPNP is not set
CONFIG_USB_AUERISDN=m

#
# Active ISDN cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=m
CONFIG_ISDN_DRV_ACT2000=m
CONFIG_ISDN_DRV_EICON=y
CONFIG_ISDN_DRV_EICON_DIVAS=m
CONFIG_ISDN_DRV_EICON_OLD=m
CONFIG_ISDN_DRV_EICON_PCI=y
CONFIG_ISDN_DRV_EICON_ISA=y
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
# CONFIG_ISDN_CAPI_MIDDLEWARE is not set
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIDRV=m
CONFIG_ISDN_DRV_AVMB1_B1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
CONFIG_ISDN_DRV_AVMB1_T1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
# CONFIG_ISDN_DRV_AVMB1_AVM_CS is not set
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m
CONFIG_HYSDN=m
# CONFIG_HYSDN_CAPI is not set

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Input core support
#
CONFIG_INPUT=m
CONFIG_INPUT_KEYBDEV=m
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_UINPUT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
CONFIG_SERIAL_EXTENDED=y
CONFIG_SERIAL_MANY_PORTS=y
CONFIG_SERIAL_SHARE_IRQ=y
# CONFIG_SERIAL_DETECT_IRQ is not set
CONFIG_SERIAL_MULTIPORT=y
CONFIG_HUB6=y
CONFIG_SERIAL_NONSTANDARD=y
CONFIG_COMPUTONE=m
CONFIG_ROCKETPORT=m
CONFIG_CYCLADES=m
CONFIG_DIGIEPCA=m
CONFIG_ESPSERIAL=m
CONFIG_MOXA_INTELLIO=m
CONFIG_MOXA_SMARTIO=m
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_N_HDLC=m
CONFIG_RISCOM8=m
CONFIG_SPECIALIX=m
# CONFIG_SPECIALIX_RTSCTS is not set
CONFIG_SX=m
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=m
CONFIG_TIPAR=m

#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_PHILIPSPAR=m
CONFIG_I2C_ELV=m
CONFIG_I2C_VELLEMAN=m
# CONFIG_SCx200_I2C is not set
CONFIG_SCx200_ACB=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ELEKTOR=m
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_PROC=m

#
# Mice
#
CONFIG_BUSMOUSE=m
CONFIG_ATIXL_BUSMOUSE=m
CONFIG_LOGIBUSMOUSE=m
CONFIG_MS_BUSMOUSE=m
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
CONFIG_82C710_MOUSE=m
CONFIG_PC110_PAD=m
CONFIG_MK712_MOUSE=m

#
# Joysticks
#
CONFIG_INPUT_GAMEPORT=m
CONFIG_INPUT_NS558=m
CONFIG_INPUT_LIGHTNING=m
CONFIG_INPUT_PCIGAME=m
CONFIG_INPUT_CS461X=m
CONFIG_INPUT_EMU10K1=m
CONFIG_INPUT_SERIO=m
CONFIG_INPUT_SERPORT=m
CONFIG_INPUT_ANALOG=m
CONFIG_INPUT_A3D=m
CONFIG_INPUT_ADI=m
CONFIG_INPUT_COBRA=m
CONFIG_INPUT_GF2K=m
CONFIG_INPUT_GRIP=m
CONFIG_INPUT_INTERACT=m
CONFIG_INPUT_TMDC=m
CONFIG_INPUT_SIDEWINDER=m
CONFIG_INPUT_IFORCE_USB=m
CONFIG_INPUT_IFORCE_232=m
CONFIG_INPUT_WARRIOR=m
CONFIG_INPUT_MAGELLAN=m
CONFIG_INPUT_SPACEORB=m
CONFIG_INPUT_SPACEBALL=m
CONFIG_INPUT_STINGER=m
CONFIG_INPUT_DB9=m
CONFIG_INPUT_GAMECON=m
CONFIG_INPUT_TURBOGRAFX=m
CONFIG_QIC02_TAPE=m
# CONFIG_QIC02_DYNCONF is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_IPMI_PANIC_EVENT is not set
# CONFIG_IPMI_DEVICE_INTERFACE is not set
# CONFIG_IPMI_KCS is not set
# CONFIG_IPMI_WATCHDOG is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_SCx200 is not set
# CONFIG_SCx200_GPIO is not set
# CONFIG_AMD_RNG is not set
CONFIG_INTEL_RNG=m
CONFIG_HW_RANDOM=m
# CONFIG_AMD_PM768 is not set
CONFIG_NVRAM=m
CONFIG_RTC=y
CONFIG_DTLK=m
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
CONFIG_FTAPE=m
CONFIG_ZFTAPE=m
CONFIG_ZFT_DFLT_BLK_SZ=10240
CONFIG_ZFT_COMPRESSOR=m
# CONFIG_FT_PROC_FS is not set
CONFIG_FT_NORMAL_DEBUG=y
# CONFIG_FT_FULL_DEBUG is not set
# CONFIG_FT_NO_TRACE is not set
# CONFIG_FT_NO_TRACE_AT_ALL is not set
CONFIG_FT_STD_FDC=y
# CONFIG_FT_MACH2 is not set
# CONFIG_FT_PROBE_FC10 is not set
# CONFIG_FT_ALT_FDC is not set
CONFIG_FT_ALPHA_CLOCK=0
CONFIG_AGP=m
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_I810 is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD_K8 is not set
CONFIG_AGP_SIS=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_ATI is not set

#
# Direct Rendering Manager (XFree86 DRI support)
#
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_OBMOUSE is not set

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m

#
# Video For Linux
#
CONFIG_VIDEO_PROC_FS=y
CONFIG_I2C_PARPORT=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_PMS=m
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_W9966=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_PP=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZR36120=m

#
# Radio Adapters
#
CONFIG_RADIO_CADET=m
CONFIG_RADIO_RTRACK=m
CONFIG_RADIO_RTRACK2=m
CONFIG_RADIO_AZTECH=m
CONFIG_RADIO_GEMTEK=m
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
# CONFIG_RADIO_MIROPCM20 is not set
# CONFIG_RADIO_MIROPCM20_RDS is not set
CONFIG_RADIO_SF16FMI=m
CONFIG_RADIO_SF16FMR2=m
CONFIG_RADIO_TERRATEC=m
CONFIG_RADIO_TRUST=m
CONFIG_RADIO_TYPHOON=m
CONFIG_RADIO_TYPHOON_PROC_FS=y
CONFIG_RADIO_ZOLTRIX=m

#
# File systems
#
CONFIG_QUOTA=y
CONFIG_QFMT_V2=m
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
# CONFIG_FAT_FS is not set
# CONFIG_MSDOS_FS is not set
# CONFIG_UMSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_TMPFS is not set
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
# CONFIG_JFS_FS is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_XFS_FS is not set
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_RT is not set
# CONFIG_XFS_TRACE is not set
# CONFIG_XFS_DEBUG is not set

#
# Network File Systems
#
CONFIG_CODA_FS=m
# CONFIG_INTERMEZZO_FS is not set
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_TCP is not set
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
# CONFIG_SMB_FS is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
CONFIG_ZISOFS_FS=y

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_SMB_NLS is not set
CONFIG_NLS=y

#
# Native Language Support
#
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
CONFIG_NLS_CODEPAGE_860=m
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
CONFIG_NLS_CODEPAGE_863=m
# CONFIG_NLS_CODEPAGE_864 is not set
CONFIG_NLS_CODEPAGE_865=m
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
# CONFIG_NLS_KOI8_R is not set
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m

#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set

#
# Sound
#
CONFIG_SOUND=y
# CONFIG_SOUND_ALI5455 is not set
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_MIDI_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_FORTE is not set
CONFIG_SOUND_ICH=m
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
CONFIG_SOUND_TRIDENT=m
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_MIDI_VIA82CXXX is not set
CONFIG_SOUND_OSS=y
CONFIG_SOUND_TRACEINIT=y
# CONFIG_SOUND_DMAP is not set
# CONFIG_SOUND_SGALAXY is not set
CONFIG_SOUND_ADLIB=m
# CONFIG_SOUND_ACI_MIXER is not set
# CONFIG_SOUND_CS4232 is not set
# CONFIG_SOUND_SSCAPE is not set
# CONFIG_SOUND_GUS is not set
CONFIG_SOUND_VMIDI=m
# CONFIG_SOUND_TRIX is not set
CONFIG_SOUND_MSS=m
# CONFIG_SOUND_MPU401 is not set
# CONFIG_SOUND_NM256 is not set
# CONFIG_SOUND_MAD16 is not set
# CONFIG_SOUND_PAS is not set
# CONFIG_PAS_JOYSTICK is not set
# CONFIG_SOUND_PSS is not set
CONFIG_SOUND_SB=m
CONFIG_SOUND_AWE32_SYNTH=m
# CONFIG_SOUND_KAHLUA is not set
CONFIG_SOUND_WAVEFRONT=m
CONFIG_SOUND_MAUI=m
# CONFIG_SOUND_YM3812 is not set
CONFIG_SOUND_OPL3SA1=m
CONFIG_SOUND_OPL3SA2=m
# CONFIG_SOUND_YMFPCI is not set
# CONFIG_SOUND_YMFPCI_LEGACY is not set
# CONFIG_SOUND_UART6850 is not set
# CONFIG_SOUND_AEDSP16 is not set
# CONFIG_SOUND_TVMIXER is not set
# CONFIG_SOUND_AD1980 is not set
# CONFIG_SOUND_WM97XX is not set

#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_UHCI=m
CONFIG_USB_UHCI_ALT=m
CONFIG_USB_OHCI=m
# CONFIG_USB_SL811HS_ALT is not set
# CONFIG_USB_SL811HS is not set
CONFIG_USB_AUDIO=m
CONFIG_USB_EMI26=m
CONFIG_USB_MIDI=m
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
CONFIG_USB_HIDDEV=y
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
CONFIG_USB_KBTAB=m
CONFIG_USB_POWERMATE=m
CONFIG_USB_DC2XX=m
# CONFIG_USB_MDC800 is not set
CONFIG_USB_SCANNER=m
CONFIG_USB_MICROTEK=m
# CONFIG_USB_HPUSBSCSI is not set
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_OV511=m
CONFIG_USB_PWC=m
CONFIG_USB_SE401=m
CONFIG_USB_STV680=m
CONFIG_USB_W9968CF=m
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
CONFIG_USB_DABUSB=m
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_USS720=m

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
# CONFIG_USB_SERIAL_DEBUG is not set
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
# CONFIG_USB_SERIAL_IR is not set
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_KLSI=m
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set
# CONFIG_USB_RIO500 is not set
CONFIG_USB_AUERSWALD=m
CONFIG_USB_TIGL=m
# CONFIG_USB_BRLVGER is not set
CONFIG_USB_LCD=m

#
# Support for USB gadgets
#
# CONFIG_USB_GADGET is not set

#
# Bluetooth support
#
CONFIG_BLUEZ=m
CONFIG_BLUEZ_L2CAP=m
CONFIG_BLUEZ_SCO=m
CONFIG_BLUEZ_RFCOMM=m
CONFIG_BLUEZ_RFCOMM_TTY=y
CONFIG_BLUEZ_BNEP=m
CONFIG_BLUEZ_BNEP_MC_FILTER=y
CONFIG_BLUEZ_BNEP_PROTO_FILTER=y
CONFIG_BLUEZ_CMTP=m

#
# Bluetooth device drivers
#
CONFIG_BLUEZ_HCIUSB=m
# CONFIG_BLUEZ_HCIUSB_SCO is not set
CONFIG_BLUEZ_HCIUART=m
CONFIG_BLUEZ_HCIUART_H4=y
CONFIG_BLUEZ_HCIUART_BCSP=y
CONFIG_BLUEZ_HCIUART_BCSP_TXCRC=y
CONFIG_BLUEZ_HCIBFUSB=m
# CONFIG_BLUEZ_HCIDTL1 is not set
# CONFIG_BLUEZ_HCIBT3C is not set
# CONFIG_BLUEZ_HCIBLUECARD is not set
# CONFIG_BLUEZ_HCIBTUART is not set
CONFIG_BLUEZ_HCIVHCI=m

#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=0

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_ARC4 is not set
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_TEST=m

#
# Library routines
#
CONFIG_CRC32=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
[4.] Kernel version (from /proc/version):
Linux version 2.4.26 (system@palantir) (gcc version 3.3.3) #4 SMP Fri May 14 14:35:36 CEST 2004
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
[6.] A small shell script or example program which triggers the
problem (if possible)
as aforementioned:
( cd /var/tmp/. ; tar -cf - . ) | tar -xvf -
from /vat/tmp/. on IDE disc partition to curent on scsi disc partition
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
Note: obviously run after reboot.
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.

Linux palantir 2.4.26 #4 SMP Fri May 14 14:35:36 CEST 2004 i686 unknown

Gnu C 3.2.3
Gnu make 3.80
util-linux 2.12
mount 2.12
modutils 2.4.22
e2fsprogs 1.34
reiserfsprogs 3.6.8
pcmcia-cs 3.2.4
quota-tools 3.08.
PPP 2.4.1
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Linux C++ Library 5.0.3
Procps 2.0.14
Net-tools 1.60
Kbd 1.08
Sh-utils 2.0
Modules Loaded st nfsd usb-storage usb-ohci usbcore sis900 crc32
ide-scsi agpgart

[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 7
cpu MHz : 2810.053
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid
bogomips : 5609.88

[7.3.] Module information (from /proc/modules):
st 29784 0 (autoclean) (unused)
nfsd 73936 8
usb-storage 36472 0
usb-ohci 19944 0 (unused)
usbcore 66636 1 [usb-storage usb-ohci]
sis900 13676 1
crc32 2912 0 [sis900]
ide-scsi 10448 0
agpgart 14932 0 (unused)

[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cd000-000d27ff : Extension ROM
000f0000-000fffff : System ROM
00100000-1ffeffff : System RAM
00100000-00300dc1 : Kernel code
00300dc2-003a91c3 : Kernel data
1fff0000-1fff7fff : ACPI Tables
1fff8000-1fffffff : ACPI Non-volatile Storage
bf200000-df3fffff : PCI Bus #01
c8000000-cfffffff : PCI device 1002:5941 (ATI Technologies Inc)
d0000000-d7ffffff : PCI device 1002:5961 (ATI Technologies Inc)
df500000-df6fffff : PCI Bus #01
df6e0000-df6effff : PCI device 1002:5941 (ATI Technologies Inc)
df6f0000-df6fffff : PCI device 1002:5961 (ATI Technologies Inc)
df800000-dfbfffff : Intel Corp. 536EP Data Fax Modem
dfff9800-dfff9fff : VIA Technologies, Inc. IEEE 1394 Host Controller
dfffa000-dfffafff : Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet
dfffa000-dfffafff : sis900
dfffb000-dfffbfff : Silicon Integrated Systems [SiS] USB 1.0 Controller
dfffb000-dfffbfff : usb-ohci
dfffc000-dfffcfff : Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
dfffc000-dfffcfff : usb-ohci
dfffd000-dfffdfff : Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
dfffd000-dfffdfff : usb-ohci
dfffe000-dfffefff : Silicon Integrated Systems [SiS] USB 2.0 Controller
dffff000-dfffffff : Adaptec AHA-2940U2/U2W
dffff000-dfffffff : aic7xxx
e0000000-e3ffffff : Silicon Integrated Systems [SiS] SiS645 Host & Memory &
AGP Controller
fec00000-fecfffff : reserved
fee00000-feefffff : reserved
ffee0000-fff0fffe : reserved

[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645 Host & Memory & AGP Controller (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: df500000-df6fffff
Prefetchable memory behind bridge: bf200000-df3fffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 4: I/O ports at ff00 [size=16]

00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 PCI Audio Accelerator (rev a0)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7370
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at d400 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.0 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7370
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 20
Region 0: Memory at dfffb000 (32-bit, non-prefetchable) [size=4K]

00:03.1 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7370
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin B routed to IRQ 21
Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=4K]

00:03.2 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7370
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin C routed to IRQ 22
Region 0: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]

00:03.3 USB Controller: Silicon Integrated Systems [SiS] SiS7002 USB 2.0 (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 5470
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 23
Region 0: Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 90)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7370
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at dfffa000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at dffa0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 SCSI storage controller: Adaptec AHA-2940U2/U2W
Subsystem: Adaptec AHA-2940U2W SCSI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (9750ns min, 6250ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
BIST result: 00
Region 0: I/O ports at dc00 [disabled] [size=256]
Region 1: Memory at dffff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at dffc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:08.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at dfff9800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at cc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 Communication controller: Intel Corp. 536EP Data Fax Modem
Subsystem: Intel Corp.: Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df800000 (32-bit, non-prefetchable) [size=4M]
Capabilities: [e0] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=375mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5961 (rev 01) (prog-if 00 [VGA])
Subsystem: Hightech Information System Ltd.: Unknown device 200c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at a800 [size=256]
Region 2: Memory at df6f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at df6c0000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.1 Display controller: ATI Technologies Inc: Unknown device 5941 (rev 01)
Subsystem: Hightech Information System Ltd.: Unknown device 200d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 08
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at df6e0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

[7.6.] SCSI information (from /proc/scsi/scsi)
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: QUANTUM Model: ATLAS 10K 9WLS Rev: UCH0
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020W
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: MATSHITA Model: DVD-ROM SR-8588 Rev: 7Z14
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: MATSHITA Model: DVD-RAM SW-9581 Rev: B100
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: ICSI Model: CF Card CF Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 01
Vendor: ICSI Model: MS Card MS Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 02
Vendor: ICSI Model: SD Card MMC/SD Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 03
Vendor: ICSI Model: SM Rev: 1.2F
Type: Direct-Access ANSI SCSI revision: 02

[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):

/proc/dma:

4: cascade
interrupts:
CPU0
0: 297307 IO-APIC-edge timer
1: 6 IO-APIC-edge keyboard
2: 0 XT-PIC cascade
8: 1 IO-APIC-edge rtc
12: 11 IO-APIC-edge PS/2 Mouse
14: 68573 IO-APIC-edge ide0
15: 215 IO-APIC-edge ide1
17: 362 IO-APIC-level aic7xxx
19: 80080 IO-APIC-level eth0
20: 174 IO-APIC-level usb-ohci
21: 0 IO-APIC-level usb-ohci
22: 0 IO-APIC-level usb-ohci
NMI: 0
LOC: 297261
ERR: 0
MIS: 0

/proc/ide/drivers:

ide-scsi version 0.93
ide-floppy version 0.99.newide
ide-cdrom version 4.59-ac1
ide-disk version 1.17
ide-default version 0.9.newide

/proc/ide/hda/settings:

name value min max mode
---- ----- --- --- ----
acoustic 0 0 254 rw
address 1 0 2 rw
bios_cyl 19929 0 65535 rw
bios_head 255 0 255 rw
bios_sect 63 0 63 rw
breada_readahead 8 0 255 rw
bswap 0 0 1 r
current_speed 70 0 70 rw
failures 0 0 65535 rw
file_readahead 124 0 16384 rw
init_speed 70 0 70 rw
io_32bit 0 0 3 rw
keepsettings 0 0 1 rw
lun 0 0 7 rw
max_failures 1 0 65535 rw
max_kb_per_request 128 1 255 rw
multcount 16 0 16 rw
nice1 1 0 1 rw
nowerr 0 0 1 rw
number 0 0 3 rw
pio_mode write-only 0 255 w
slow 0 0 1 rw
unmaskirq 0 0 1 rw
using_dma 1 0 1 rw

/proc/scsi/aic7xxx/0:

Adaptec AIC7xxx driver version: 6.2.36
Adaptec 2940 Ultra2 SCSI adapter
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
Allocated SCBs: 10, SG List Length: 102

Serial EEPROM:
0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb
0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb 0xc3bb
0x1006 0x1c4d 0x2807 0x0010 0xffff 0xffff 0xffff 0xffff
0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0x900f

Target 0 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 1 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Goal: 40.000MB/s transfers (20.000MHz, offset 31, 16bit)
Curr: 40.000MB/s transfers (20.000MHz, offset 31, 16bit)
Channel A Target 1 Lun 0 Settings
Commands Queued 94
Commands Active 0
Command Openings 8
Max Tagged Openings 8
Device Queue Frozen Count 0
Target 2 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 3 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Goal: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Curr: 40.000MB/s transfers (20.000MHz, offset 127, 16bit)
Channel A Target 3 Lun 0 Settings
Commands Queued 188
Commands Active 0
Command Openings 8
Max Tagged Openings 8
Device Queue Frozen Count 0
Target 4 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 5 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 6 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 7 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 8 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 9 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 10 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 11 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 12 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 13 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 14 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
Target 15 Negotiation Settings
User: 80.000MB/s transfers (40.000MHz, offset 127, 16bit)

[X.] Other notes, patches, fixes, workarounds:
None. Similar errors also occur in a 2.4.22 kernel as disctributed by
Slackware.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Andrew Morton: "Re: [PATCH] Quota fix 3 - quota file corruption"
Previous message: Bill Davidsen: "Re: 2.6.6-mm2"
Next in thread: Marcelo Tosatti: "Re: PROBLEM: SCSI failure resulting in kernel panic"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]