More 2.6.0-test6 PCMCIA and Orinoco problems
From: Joshua M. Thompson
Date: Tue Oct 07 2003 - 10:39:31 EST
Been searching the net and list archives for a three days now and can't
find any reports of this exact problem, so here goes:
I finally decided to try out 2.6 on my notebook again. It's a Gateway
600E (P4-M 2.0, Intel 845 chipset, TI PCI1250 cardbus controller)
running RedHat 9.0, upgraded with the beta RPMS from
http://people.redhat.com/arjanv/2.5/. I'm up and running MOSTLY ok
except that I can't get PCMCIA to work. Specifically, my built-in
Orinoco wireless card doesn't work anymore, nor does an Orinoco Gold
card I happen to have lying around. PCMCIA starts up ok and the
orinoco_cs driver loads; however it fails to start, giving only the
error message "ds: unable to create instance of 'orinoco_cs'".
I've tried several solutions. Tried booting with ACPI off, with APIC
off, and even tried "cardctl eject; cardctl insert" which seems to help
some people. Same error every time. The wireless card works fine with
2.4.20 and also worked fine when I briefly tried 2.5.68 a while back.
Here's my dmesg output:
Linux version 2.6.0-0.test6.1.48 (bhcompile@xxxxxxxxxxxxxxxxxxxxxx) (gcc
version 3.3.1 20030930 (Red Hat Linux 3.3.1-6)) #1 Fri Oct
3 07:53:36 EDT 2003
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data)
BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 000000001ff00000 - 000000001ff80000 (usable)
BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 130944
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126848 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @
0x000f6620
ACPI: RSDT (v001 GATEWA 600YG2 0x20021212 LTP 0x00000000) @
0x1fef8198
ACPI: FADT (v001 GATEWA 600YG2 0x20021212 PTL 0x0000001e) @
0x1fefef64
ACPI: BOOT (v001 GATEWA 600YG2 0x20021212 LTP 0x00000001) @
0x1fefefd8
ACPI: DSDT (v001 GATEWA 600YG2 0x20021212 MSFT 0x0100000e) @
0x00000000
Building zonelist for node : 0
Kernel command line: ro root=LABEL=/ hdb=ide-scsi
ide_setup: hdb=ide-scsi
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1995.118 MHz processor.
Console: colour VGA+ 80x25
Memory: 514844k/523776k available (1641k kernel code, 8096k reserved,
712k data, 156k init, 0k highmem)
Calibrating delay loop... 3932.16 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security
failed.
Failure registering capabilities with the kernel
selinux_register_security: Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebf9ff 00000000 00000000
00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000
00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd999, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20030918
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10)
ACPI: PCI Interrupt Link [LNKF] (IRQs 10)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10)
ACPI: PCI Interrupt Link [LNKH] (IRQs 10)
ACPI: Embedded Controller [EC0] (gpe 29)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
divert: not allocating divert_blk for non-ethernet device lo
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
pty: 2048 Unix98 ptys configured
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i845 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xec000000
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:pio, hdd:pio
hda: IC25N040ATCS04-0, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-R6012, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/1768KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 28
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
serio: i8042 AUX3 port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 172k freed
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 156k freed
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface
driver v2.1
uhci-hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci-hcd 0000:00:1d.0: irq 10, io base 00001800
uhci-hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci-hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci-hcd 0000:00:1d.1: irq 5, io base 00001820
uhci-hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver hiddev
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
EXT3 FS on hda2, internal journal
Adding 1052216k swap on /dev/hda5. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 1045 $ Ben Collins <bcollins@xxxxxxxxxx>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[e8208000-e82087ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0b80602006c1d]
SCSI subsystem initialized
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-R6012 Rev: 1G32
Type: CD-ROM ANSI SCSI revision: 02
kudzu: numerical sysctl 1 23 is obsolete.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
inserting floppy driver for 2.6.0-0.test6.1.48
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ip_tables: (C) 2000-2002 Netfilter core team
Disabled Privacy Extensions on device c0319060(lo)
ip_tables: (C) 2000-2002 Netfilter core team
Intel(R) PRO/100 Network Driver - version 2.3.30-k1
Copyright (c) 2003 Intel Corporation
divert: allocating divert_blk for eth0
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:02.0 [107b:0602]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ list 0898, PCI irq10
Socket status: 30000006
Yenta: CardBus bridge found at 0000:02:02.1 [107b:0602]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ list 0898, PCI irq10
Socket status: 30000006
PCI: Enabling device 0000:02:04.0 (0104 -> 0106)
Yenta: CardBus bridge found at 0000:02:04.0 [12a3:ab01]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ list 0000, PCI irq10
Socket status: 30000010
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x1c0-0x1cf
0x370-0x37f 0x3c0-0x3df 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes@xxxxxxxxxxxxxxxxxxxxx> and others)
orinoco_cs.c 0.13e (David Gibson <hermes@xxxxxxxxxxxxxxxxxxxxx> and
others)
ds: unable to create instance of 'orinoco_cs'!
And, for comparison, here is a normal boot on 2.4.20:
Linux version 2.4.20-20.9 (bhcompile@xxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc
version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon Aug 18
11:45:58 EDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data)
BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 000000001ff00000 - 000000001ff80000 (usable)
BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 130944
zone(0): 4096 pages.
zone(1): 126848 pages.
zone(2): 0 pages.
Kernel command line: ro root=LABEL=/ hdb=ide-scsi
ide_setup: hdb=ide-scsi
Initializing CPU#0
Detected 1994.167 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3971.48 BogoMIPS
Memory: 510804k/523776k available (1358k kernel code, 10340k reserved,
1004k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebf9ff 00000000 00000000 00000000
CPU: Common caps: bfebf9ff 00000000 00000000 00000000
CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd999, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Using IRQ router PIIX [8086/248c] at 00:1f.0
PCI: Found IRQ 10 for device 00:1f.1
PCI: Sharing IRQ 10 with 02:02.0
PCI: Sharing IRQ 10 with 02:02.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 00:1f.6
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 02:05.0
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH3M: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: Found IRQ 10 for device 00:1f.1
PCI: Sharing IRQ 10 with 02:02.0
PCI: Sharing IRQ 10 with 02:02.1
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:pio, hdd:pio
hda: IC25N040ATCS04-0, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-R6012, ATAPI CD/DVD-ROM drive
blk: queue c03cdfe0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78140160 sectors (40008 MB) w/1768KiB Cache, CHS=4864/255/63,
UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 166k freed
VFS: Mounted root (ext2 filesystem).
LVM version 1.0.5+(22/07/2002) module loaded
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 11:55:13 Aug 18 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:1d.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:1d.1
PCI: Sharing IRQ 5 with 02:03.0
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
loop: loaded (max 8 devices)
Adding Swap: 1052216k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 693 $ Ben Collins <bcollins@xxxxxxxxxx>
PCI: Found IRQ 10 for device 02:05.0
PCI: Sharing IRQ 10 with 00:1f.3
PCI: Sharing IRQ 10 with 00:1f.6
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[e8208000-e82087ff] Max
Packet=[2048]
ieee1394: SelfID completion called outside of bus reset!
ieee1394: Host added: Node[00:1023] GUID[00e0b80602006c1d] [Linux
OHCI-1394]
SCSI subsystem driver Revision: 1.00
hdb: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-R6012 Rev: 1G32
Type: CD-ROM ANSI SCSI revision: 02
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
Intel(R) PRO/100 Network Driver - version 2.2.21-k1
Copyright (c) 2003 Intel Corporation
PCI: Found IRQ 10 for device 02:08.0
PCI: Sharing IRQ 10 with 02:04.0
e100: selftest OK.
divert: allocating divert_blk for eth0
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 02:02.0
PCI: Sharing IRQ 10 with 00:1f.1
PCI: Sharing IRQ 10 with 02:02.1
PCI: Found IRQ 10 for device 02:02.1
PCI: Sharing IRQ 10 with 00:1f.1
PCI: Sharing IRQ 10 with 02:02.0
PCI: Enabling device 02:04.0 (0104 -> 0106)
PCI: Found IRQ 10 for device 02:04.0
PCI: Sharing IRQ 10 with 02:08.0
Yenta IRQ list 0a98, PCI irq10
Socket status: 30000006
Yenta IRQ list 0a98, PCI irq10
Socket status: 30000006
Yenta IRQ list 0000, PCI irq10
Socket status: 30000010
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x1c0-0x1cf
0x370-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
hermes.c: 4 Dec 2002 David Gibson <hermes@xxxxxxxxxxxxxxxxxxxxx>
orinoco.c 0.13d (David Gibson <hermes@xxxxxxxxxxxxxxxxxxxxx> and others)
orinoco_cs.c 0.13d (David Gibson <hermes@xxxxxxxxxxxxxxxxxxxxx> and
others)
divert: allocating divert_blk for eth1
eth1: Station identity 001f:0001:0008:000a
eth1: Looks like a Lucent/Agere firmware version 8.10
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:B0:CF:C7
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 10, io 0x0100-0x013f
eth1: New link status: Connected (0001)
Both kernel versions map the Yenta controllers onto irq 10. In fact the
only difference in /proc/interrupts between the two versions is ACPI
takes irq 9 in 2.6, and as I mentioned above booting without ACPI
enabled does not solve the problem.
If anyone needs additional information let me know.
--
Joshua M. Thompson <funaho@xxxxxxxxx>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/