fatal errors in test4/5 with APIC and IRQ routing in Acer 1310LClaptop

From: Pau Aliagas
Date: Thu Sep 11 2003 - 07:39:29 EST

Next message: Claas Langbehn: "Re: [2.6.0-test5-mm1] Suspend to RAM problems"
Previous message: Jamie Lokier: "Re: Virtual alias cache coherency results (was: x86, ARM, PARISC, PPC, MIPS and Sparc folks please run this)"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

First of all, I have to boot with pci=noacpi pci=usepirqmask pci=biosirq,
otherwise, when ifuping the integrated Ethernet controller: VIA
Technologies, Inc. VT6102 [Rhine-II], the system freezes with the floppy
light on.

But this is only the first of a set of problems due to IRQs. With this
kernel parametres, neither the PCMCIA Cardbus nor the USB are properly
configured, resulting in freezes when inserting or ejecting pcmcia cards,
or a bluetooth usb device.

If I use a stock redhat 2.4.20 kernel USB+bluetooh are properly detected
and PCMCIA does not hang the computer.

More things: ACPI also hangs the laptop when trying to suspend using the
sys iterface.

I attach the lspci -vvb output (nooting with the aforementioned
parametres). I can provide more information, if needed.

00:00.0 Host bridge: VIA Technologies, Inc. P/KN266 Host Bridge
Subsystem: VIA Technologies, Inc. P/KN266 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at b0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: e0000000-efffffff
Prefetchable memory behind bridge: a0000000-afffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
Subsystem: Citicorp TTI: Unknown device 10e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 2e000000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 2e400000-2e7ff000 (prefetchable)
Memory window 1: 2e800000-2ebff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001

00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Citicorp TTI: Unknown device 1162
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (500ns min, 1000ns max), cache line size 04
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0000000 (32-bit, non-prefetchable)
Region 1: Memory at f0004000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 22
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1200
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 22
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 1300
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 0
Region 0: Memory at f4000000 (32-bit, non-prefetchable)
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at 1100
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
Subsystem: Acer Incorporated [ALI]: Unknown device 0030
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at e000
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 80)
Subsystem: Acer Incorporated [ALI]: Unknown device 0030
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at e100
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: Acer Incorporated [ALI]: Unknown device 0030
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (750ns min, 2000ns max), cache line size 04
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e200
Region 1: Memory at f0008000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

01:00.0 VGA compatible controller: S3 Inc. [ProSavageDDR K4M266] (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI]: Unknown device 0030
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max), cache line size 04
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0080000 (32-bit, non-prefetchable)
Region 1: Memory at a8000000 (32-bit, prefetchable)
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x4

Pau

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Claas Langbehn: "Re: [2.6.0-test5-mm1] Suspend to RAM problems"
Previous message: Jamie Lokier: "Re: Virtual alias cache coherency results (was: x86, ARM, PARISC, PPC, MIPS and Sparc folks please run this)"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]