Paul Flinders <P.Flinders@ftel.co.uk> writes:
> Has anyone got either 2.2.x or 2.4.0 booted on the above motherboard?
I've got an MSI 694D Pro AI mainboard (ie non-raid), and both 2.2.x
and 2.4.0 work flawlessly here. I did manage to build a 2.4.0 kernel
which didn't boot, but it got much further before it hung. I didn't
try to find out why, just changed some settings (removing APM/ACPI,
iirc), so I'm not sure why.
> This board has an integrated Promise Fasttrack ATA/100 controller - I
> know that to support the hardware RAID I need the binary only drivers
> from Promise but I'd rather not use these if software RAID works as
> there's no source, however I'm not getting that far.
My board doesn't have RAID, but it has a Promise PDC20627
ATA/100-controller, which is properly detected (although I haven't
tried to run it at UDMA 100-speeds, I can't see why it shouldn't as
long as the controller is supported) Currently there are no disks on
the promise controller, but I've tried that, and I know it works.
> PDC20265: IDE controller on PCI bus 00 dev 60
> PDC20265: Chipset Revision 2
> PDC20265: not 100% native mode: will probe irqs later
> PDC20265: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode.
> ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:pio, hdf:pio
>
> Then it hangs requiring power cycling.
>
> I'm not sure whether the I/O address reported by the promise driver is
> correct - the promise BIOS shows the I/O address for the first channel
> as 0xCC00.
Here is my output from 2.4.0, SMP, same section:
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a IDE UDMA66 controller on pci0:7.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:DMA
PDC20267: IDE controller on PCI bus 00 dev 60
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0xac00-0xac07, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xac08-0xac0f, BIOS settings: hdg:pio, hdh:DMA
hda: IBM-DTLA-307030, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdc: IBM-DTTA-371010, ATA DISK drive
hdd: ST38641A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, UDMA(66)
hdc: 19746720 sectors (10110 MB) w/465KiB Cache, CHS=19590/16/63, UDMA(33)
hdd: 16809660 sectors (8607 MB) w/128KiB Cache, CHS=16676/16/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 >
/dev/ide/host0/bus1/target0/lun0: [PTBL] [1229/255/63] p1 p2 < p5 p6 p7 p8 >
/dev/ide/host0/bus1/target1/lun0: p1
> Is this a configuration with known problems?
Unless it's either the RAID that's causing you problems, or the maxtor
drives, I don't know what could cause this. I'm not sure which
BIOS-version is on my card, but I haven't touched it.
-- Håvard Lygre, hklygre@online.no Bergen IT-Teknikk ANS, Conrad Mohrsvei 11, 5068 Bergen Tlf: 55 360773 Fax: 55 360774 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Jan 15 2001 - 21:00:25 EST