I have also a lockup problem that maybe has similarity with this...
HW: MB SOYO 6BA+IV (http://www.soyo.nl/product/6ba+iv.htm) with PIIX 2 x
Ultra/33 channels and HPT366 2 x Ultra/66, Quantum lct10 15, UDMA4 15GB
SW: RH6.2, 2.2.14+2.3.99pre5
I have ATAPI CD-ROM on hdc and the Quantum on hde.
On 2.3.99pre5 boot it recognizes the PIIX and the HPT366 ok, recognizes the
hdc SONY CDU311 and freezes and the disks LED is on all the time.
If I put bootparams ide=reverse, hda=1826,255,63 (the quantum), the
controllers are swapped, and I get oops, then register listing...
I also have another kernel 2.2.14 from the RH 6.2 distribution and I can
boot from hde with it when I put bootparams: ide2=0xd400,0xd802,
ide=noprobe.
Any ideas?
Regards,
Sasho Trendafilov
e-mail: brainsurf@mt.net.mk
----- Original Message -----
From: bug1 <bug1@netconnect.com.au>
To: <linux-kernel@vger.rutgers.edu>
Sent: Friday, April 21, 2000 5:07 AM
Subject: oops on partition check, depending on drive order
> Hi, ive been gettign strange behaviour on my dual celeron bp6 with disk
> behaviour for a few days, ive tried 2.3.99pre3, 2.3.99pre5, but am now
> using 2.3.99pre6pre3.
>
> I wish i could rule out hardware problem, but i really dont know what
> the cause of my problem is. My system locks up on boot detecting
> partitions, depending on the order of the drives, when i do boot i get
> lookups when reading from my 4 way ide raid0.
>
> When i boot succesfully and read my array i get ide_dma_timeout func
> only:14, i can write no problems (55MB/s on raid0 :)) but reading cause
> this error after about 1/2 second of begining to read.
>
> lockup on boot depending on which controller my ide drives are plugged
> into.
>
> I have 6 ide channels on my machine, 4 from my bp6 and 2 from pci hpt366
> (abit hotrod) controller card.
>
> The drive i have are
> Quantum fireball EX6.4A, this has always been plugged into my udma33
> slot, never had a problem with this one.
>
> Two 20.5GB IBM-DPTA-372050
> One Quantum Fireball Plus KA18.2
> One Quantum Fireball Plus KX20.5
>
> I can boot with any combination of 4 drives.
>
> I can succesfully boot with both ibm drives on the controller 3+4 on
> mobo, and quantum drives on my pci udma66 card
> hda: Quantum EX6.4
> hdc: IBM-DPTA (udma 4)
> hde: Quantum KA (udma 2)
> hdg: Quantum KX (udma 4)
> hdi: IDM-DPTA (udma 4)
>
> NOTE: the secondary onboard udma33 channel is disabled, so hdk (or hdi?)
> becomes hdc
>
> If i swap the position of my quantum drives on the pci udma controller,
> i can still boot.
>
> If i swap the position of my ibm drives on my onboard controller i can
> still boot.
>
> BUT if i put a ibm and a quntum plus drives togther on my onboard udma
> channels AND on my pci card, it locks up and display the data below.
>
> hda: Quantum Ex6.4
> hdc: IBM (remember hdc is really 6th channel, channel2 disabled in
> bios)
> hde: IBM
> hdg: Quantum ka
> hdi: Quantum kx
>
> or
>
> hda: Quantum ex6.4
> hdc: ibm
> hde: Quantum ka
> hdg: ibm
> hdi: Quantum kx
>
> I havent worked out how to use ksymoops properly yet, so this is all i
> have.
>
> First time i got this
>
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> hdc: hdc1 hdc2
> hde: hde1 hde2
> hdg:NMI Watchdog detected LOCKUP on CPU0, registers:
> CPU: 0
> EIP: 0010:[<c01e9ab9>]
> EFLAGS: 00000006
> eax: 00000050 ebx: c12991c0 ecx: 00000000 edx: 0000a407
> esi: c129c360 edi: 00000286 ebp: c03e5140 esp: c1273d80
> ds: 0018 es: 0018 ss: 0018
> Process swapper (pid: 1, stackpage=c1273000)
> Stack: c12991c0 04000001 00000000 00000012 00000000 00000000 c010db01
> 00000012
> c129c360 c1273de4 c0349a40 c0349a50 00000012 c1273ddc c010de34
> 00000012
> c1273de4 c127dbe0 c03e5180 00000282 c12910a8 00000000 c127dbe0
> c1273e68
> Call Trace: [<c010db01>] [<c010de34>] [<c010bee0>] [<c01e0018>]
> [<c01ad1ab>] [<c013efd1>] [<c0140b61>]
> [<c015b521>] [<c015b160>] [<c010bee0>] [<c015b23d>] [<c015b1ca>]
> [<c01e82fb>] [<c0110018>] [<c01071cb>]
> [<c0109010>]
> Code: e6 80 81 3d 28 f4 2f c0 ad 4e ad de 74 19 6a 5c 68 80 e2 2b
> console shuts up ...
>
> rebooted and this time it i struck problems at hde:
>
> The registers ebx, edx, esi, ebp, and the Stack are different from above
> but everything else is the same.
>
> Stopped at hde, some of the output is.
>
> EIP: 0010:[<c010de3e>]
> EFLAGS: 00000046
>
> Call Trace: [<c010bee0>] [c01e0018>] [<c01ad1ab>] <c013efd1>]
> [<c0140b61>] [<c015b521>] [<c015b160>]
> [c010bee0>] [<c015b23d>] [<c015b1ca>] [<c01e82fb>] [<c0110018>]
> [<c01071cb>] [<c0109010>]
> Code: 74 28 68 37 de 10 c0 68 00 ff 27 c0 e8 69 01 01 00 83 c4 08
>
> Stopped at hdg, the call trace is identical to above, but Code is.
> Code: f6 06 01 f3 90 75 f9 e9 16 63 e9 ff f6 06 01 f3 90 75 f9 e9
>
> I can reproduce more of this is needed
>
> dmesg follows
>
>
> > NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
> 00 000 00 1 0 0 0 0 0 0 00
> 01 0FF 0F 0 0 0 0 0 1 1 59
> 02 0FF 0F 0 0 0 0 0 1 1 51
> 03 0FF 0F 0 0 0 0 0 1 1 61
> 04 0FF 0F 0 0 0 0 0 1 1 69
> 05 000 00 1 0 0 0 0 0 0 00
> 06 0FF 0F 0 0 0 0 0 1 1 71
> 07 0FF 0F 0 0 0 0 0 1 1 79
> 08 0FF 0F 0 0 0 0 0 1 1 81
> 09 000 00 1 0 0 0 0 0 0 00
> 0a 000 00 1 0 0 0 0 0 0 00
> 0b 0FF 0F 0 0 0 0 0 1 1 89
> 0c 0FF 0F 0 0 0 0 0 1 1 91
> 0d 000 00 1 0 0 0 0 0 0 00
> 0e 0FF 0F 0 0 0 0 0 1 1 99
> 0f 0FF 0F 0 0 0 0 0 1 1 A1
> 10 0FF 0F 1 1 0 1 0 1 1 A9
> 11 000 00 1 0 0 0 0 0 0 00
> 12 0FF 0F 1 1 0 1 0 1 1 B1
> 13 0FF 0F 1 1 0 1 0 1 1 B9
> 14 000 00 1 0 0 0 0 0 0 00
> 15 000 00 1 0 0 0 0 0 0 00
> 16 000 00 1 0 0 0 0 0 0 00
> 17 000 00 1 0 0 0 0 0 0 00
> IRQ to pin mappings:
> IRQ0 -> 2
> IRQ1 -> 1
> IRQ3 -> 3
> IRQ4 -> 4
> IRQ6 -> 6
> IRQ7 -> 7
> IRQ8 -> 8
> IRQ11 -> 11
> IRQ12 -> 12
> IRQ13 -> 13
> IRQ14 -> 14
> IRQ15 -> 15
> IRQ16 -> 16
> IRQ18 -> 18
> IRQ19 -> 19
> .................................... done.
> calibrating APIC timer ...
> ..... CPU clock speed is 434.3800 MHz.
> ..... host bus clock speed is 66.8275 MHz.
> cpu: 0, clocks: 668275, slice: 222758
> CPU0<C0:668272,C:445504,D:10,S:222758,C:668275>
> cpu: 1, clocks: 668275, slice: 222758
> CPU1<C0:668272,C:222752,D:4,S:222758,C:668275>
> checking TSC synchronization across CPUs: passed.
> Setting commenced=1, go go go
> mtrr: your CPUs had inconsistent fixed MTRR settings
> mtrr: probably your BIOS does not setup all CPUs
> PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Using IRQ router PIIX [8086/7000] at 00:07.0
> PCI->APIC IRQ transform: (B0,I9,P0) -> 19
> PCI->APIC IRQ transform: (B0,I11,P0) -> 18
> PCI->APIC IRQ transform: (B0,I11,P0) -> 18
> PCI->APIC IRQ transform: (B0,I15,P0) -> 16
> PCI->APIC IRQ transform: (B0,I19,P0) -> 18
> PCI->APIC IRQ transform: (B0,I19,P1) -> 18
> Limiting direct PCI/PCI transfers.
> isapnp: Scanning for Pnp cards...
> isapnp: No Plug & Play device found
> Linux NET4.0 for Linux 2.3
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> IP: routing cache hash table of 512 buckets, 8Kbytes
> TCP: Hash tables configured (established 4096 bind 5461)
> Starting kswapd v1.6
> vga16fb: initializing
> vga16fb: unable to reserve VGA memory, exiting
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> loop: registered device at major 7
> loop: enabling 8 loop devices
> Uniform Multi-Platform E-IDE driver Revision: 6.30
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> PIIX4: IDE controller on PCI bus 00 dev 39
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
> HPT366: IDE controller on PCI bus 00 dev 58
> HPT366: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:DMA, hdf:pio
> HPT366: IDE controller on PCI bus 00 dev 59
> HPT366: not 100% native mode: will probe irqs later
> ide3: BM-DMA at 0xac00-0xac07, BIOS settings: hdg:DMA, hdh:pio
> HPT366: onboard version of chipset, pin1=1 pin2=2
> HPT366: IDE controller on PCI bus 00 dev 98
> HPT366: not 100% native mode: will probe irqs later
> ide1: BM-DMA at 0xb800-0xb807, BIOS settings: hdc:DMA, hdd:pio
> HPT366: IDE controller on PCI bus 00 dev 99
> HPT366: not 100% native mode: will probe irqs later
> ide4: BM-DMA at 0xc400-0xc407, BIOS settings: hdi:DMA, hdj:pio
> hda: QUANTUM FIREBALL EX6.4A, ATA DISK drive
> hdc: IBM-DPTA-372050, ATA DISK drive
> hde: QUANTUM FIREBALLP KA18.2, ATA DISK drive
> hdg: QUANTUM FIREBALLP KX20.5, ATA DISK drive
> hdi: IBM-DPTA-372050, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0xb000-0xb007,0xb402 on irq 18
> ide2 at 0x9800-0x9807,0x9c02 on irq 18
> ide3 at 0xa400-0xa407,0xa802 on irq 18
> ide4 at 0xbc00-0xbc07,0xc002 on irq 18
> hda: 12594960 sectors (6449 MB) w/418KiB Cache, CHS=13328/15/63,
> UDMA(33)
> hdc: 40088160 sectors (20525 MB) w/1961KiB Cache, CHS=39770/16/63,
> UDMA(66)
> hde: 36094464 sectors (18480 MB) w/371KiB Cache, CHS=35808/16/63,
> UDMA(33)
> hdg: 40160988 sectors (20562 MB) w/418KiB Cache, CHS=39842/16/63,
> UDMA(33)
> hdi: 40088160 sectors (20525 MB) w/1961KiB Cache, CHS=39770/16/63,
> UDMA(66)
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> hdc: hdc1 hdc2
> hde: hde1 hde2
> hdg: hdg1 hdg2
> hdi: hdi1 hdi2
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
> linear personality registered
> raid0 personality registered
> md.c: sizeof(mdp_super_t) = 4096
> LVM version 0.8final by Heinz Mauelshagen (15/02/2000)
> lvm -- Driver successfully initialized
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> scsi : 1 host.
> scsi : detected total.
> SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit
> encapsulation enabled).
> CSLIP: code copyright 1989 Regents of the University of California.
> SLIP linefill/keepalive option.
> Serial driver version 4.93 (2000-03-20) with MANY_PORTS SHARE_IRQ
> SERIAL_PCI ISAPNP enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS03 at 0x02e8 (irq = 3) is a 16550A
> Real Time Clock Driver v1.10b
> Non-volatile memory driver v1.0
> 8139too Fast Ethernet driver 0.9.4 loaded
> eth0: RealTek RTL8139 Fast Ethernet at 0xeb000000, IRQ 19,
> 00:00:1c:d0:0b:00.
> Linux agpgart interface v0.99 (c) Jeff Hartmann
> agpgart: Maximum main memory to use for agp memory: 96M
> agpgart: Detected Intel 440BX chipset
> agpgart: AGP aperture is 64M @ 0xe0000000
> kmem_create: Forcing size word alignment - nfs_fh
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 196k freed
> Adding Swap: 32564k swap-space (priority -1)
> (read) hdc1's sb offset: 11718400 [events: 00000004]
> (read) hde1's sb offset: 11718400 [events: 00000004]
> (read) hdg1's sb offset: 11718400 [events: 00000008]
> autorun ...
> considering hdg1 ...
> adding hdg1 ...
> created md0
> bind<hdg1,1>
> running: <hdg1>
> now!
> hdg1's event counter: 00000008
> md: device name has changed from [dev 39:01] to hdg1 since last import!
> md0: former device hdg1 is unavailable, removing from array!
> md0: former device hdi1 is unavailable, removing from array!
> md0: max total readahead window set to 384k
> md0: 3 data-disks, max readahead per data-disk: 128k
> md: md0, array needs 3 disks, has 1, aborting.
> raid0: disks are not ordered, aborting!
> pers->run() failed ...
> do_md_run() returned -22
> unbind<hdg1,0>
> export_rdev(hdg1)
> md0 stopped.
> considering hde1 ...
> adding hde1 ...
> adding hdc1 ...
> created md0
> bind<hdc1,1>
> bind<hde1,2>
> running: <hde1><hdc1>
> now!
> hde1's event counter: 00000004
> hdc1's event counter: 00000004
> md: device name has changed from hdg1 to hde1 since last import!
> md0: former device hde1 is unavailable, removing from array!
> md0: max total readahead window set to 384k
> md0: 3 data-disks, max readahead per data-disk: 128k
> md: md0, array needs 3 disks, has 2, aborting.
> raid0: disks are not ordered, aborting!
> pers->run() failed ...
> do_md_run() returned -22
> unbind<hde1,1>
> export_rdev(hde1)
> unbind<hdc1,0>
> export_rdev(hdc1)
> md0 stopped.
> ... autorun DONE.
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.rutgers.edu
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Apr 23 2000 - 21:00:18 EST