Hi all,
Compiled linux 2.2.15pre14 with egcs v1.0.3 and libc6 v2.0.7 for
an Dell optiplex 333mhz with crystal sound support. I've sent a copy
to the AD1816 maintainer since there is no one listed for ad1848 and he
was the closest match.
PROBLEM:
dmesg below tells me that ad1848 failed interrupt test #7.
I've included dmesg, /proc/interrupts, /dev/sndstat, the insmod
stuff from /etc/rc.d/rc.modules and my kernel config file below.
NOTE: This wasn't a problem before in previous pre kernels !
I haven't changed anything. I can play a ".wav" and midi ".mid"
file withou a problem with play/playmidi without it reporting an
interrupt conflict.
PART #1: Dmesg
Linux version 2.2.15pre14 (root@DosLinux) (gcc version egcs-2.90.29 980515 (egcs-1.0.3 release)) #1 Fri Mar 10 09:15:30 /etc/localtime 2000
Detected 331713085 Hz processor.
[snipped]
(scsi0) Cables present (Int-50 NO, Int-68 YES, Ext-68 NO)
(scsi0) Downloading sequencer code... 384 instructions downloaded
(scsi1) <Adaptec AIC-7895 Ultra SCSI host adapter> found at PCI 0/14/1
(scsi1) Narrow Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Cables present (Int-50 NO, Ext-50 NO)
(scsi1) Downloading sequencer code... 384 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
<Adaptec AIC-7895 Ultra SCSI host adapter>
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 3 hosts.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
(scsi0:0:0:0) Data overrun detected in Data-In phase, tag 1;
Have seen Data Phase. Length=255, NumSGs=1.
sg[0] - Addr 0x7fec380 : Length 255
Vendor: WDIGTL Model: WDE9100-1807A4 Rev: 1.30
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17783204 [8683 MB] [8.7 GB]
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 >
hdc: [PTBL] [621/64/63] hdc1
UMSDOS 0.85g (compatibility level 0.4, fast msdos)
check_pseudo_root: mounted as root
check_pseudo_root: found //linux
check_pseudo_root: found sbin/init, enabling pseudo-root
UMSDOS: changed to alternate root
VFS: Mounted root (umsdos filesystem).
Freeing unused kernel memory: 44k freed
CSLIP: code copyright 1989 Regents of the University of California
SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256).
SLIP linefill/keepalive option.
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
PPP BSD Compression module registered
PPP Deflate Compression module registered
********* FAILED HERE *******
ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996
ad1848: Interrupt test failed (IRQ7)
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xdc00, 00:c0:4f:78:7a:80, IRQ 11
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
MII transceiver found at address 0, status 786d.
Enabling bus-master transmits and whole-frame receives.
ppa: Version 2.03 (for Linux 2.2.x)
ppa: Found device at ID 6, Attempting to use EPP 16 bit
ppa: Found device at ID 6, Attempting to use PS/2
ppa: Communication established with ID 6 using PS/2
scsi3 : Iomega VPI0 (ppa) interface
scsi : 4 hosts.
Vendor: IOMEGA Model: ZIP 100 Rev: D.17
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sdb at scsi3, channel 0, id 6, lun 0
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sdb: Write Protect is off
sdb: sdb4
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
PART #2: /proc/interrupts
CPU0
0: 29755 XT-PIC timer
1: 809 XT-PIC keyboard
2: 0 XT-PIC cascade
7: 1699 XT-PIC Crystal audio controller
8: 1 XT-PIC rtc
11: 150443 XT-PIC aic7xxx, aic7xxx, eth0
13: 1 XT-PIC fpu
15: 31 XT-PIC ide1
NMI: 0
PART #3: /dev/sndstat
OSS/Free:3.8s2++-971130
Load type: Driver loaded as a module
Kernel: Linux DosLinux 2.2.15pre14 #1 Fri Mar 10 09:15:30 /etc/localtime 2000 i686
Config options: 0
Installed drivers:
Card config:
Audio devices:
0: Crystal audio controller (CS4236) (DUPLEX)
Synth devices:
0: Yamaha OPL3
Midi devices:
Timers:
0: System clock
Mixers:
0: Crystal audio controller (CS4236)
PART #4: insmod stuff from rc scripts
/etc/rc.d/rc.modules:/sbin/modprobe slip
/etc/rc.d/rc.modules:/sbin/modprobe ppp
/etc/rc.d/rc.modules:/sbin/modprobe bsd_comp
/etc/rc.d/rc.modules:/sbin/modprobe ppp_deflate
/etc/rc.d/rc.modules:/sbin/modprobe sound
/etc/rc.d/rc.modules:/sbin/modprobe ad1848
/etc/rc.d/rc.modules:/sbin/modprobe uart401
/etc/rc.d/rc.modules:/sbin/modprobe cs4232 io=0x534 irq=7 dma=1 dma2=0
/etc/rc.d/rc.modules:/sbin/modprobe opl3 io=0x388
/etc/rc.d/rc.modules:/sbin/modprobe 3c59x
/etc/rc.d/rc.modules:/sbin/modprobe dummy
/etc/rc.d/rc.modules:/sbin/modprobe loop
/etc/rc.d/rc.modules:/sbin/modprobe ppa
PART #5: kernel config
#
# Automatically generated by make menuconfig: don't edit
#
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
CONFIG_M586=y
# CONFIG_M586TSC is not set
# CONFIG_M686 is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_1GB=y
# CONFIG_2GB is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_MTRR is not set
# CONFIG_SMP is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
# CONFIG_KMOD is not set
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_QUIRKS=y
# CONFIG_PCI_OPTIMIZE is not set
CONFIG_PCI_OLD_PROC=y
# CONFIG_MCA is not set
# CONFIG_VISWS is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
# CONFIG_BINFMT_JAVA is not set
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
# CONFIG_PARPORT_OTHER is not set
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_IGNORE_MULTIPLE_SUSPEND is not set
CONFIG_APM_IGNORE_SUSPEND_BOUNCE=y
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
CONFIG_APM_REAL_MODE_POWER_OFF=y
#
# Plug and Play support
#
# CONFIG_PNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_VIA82C586 is not set
# CONFIG_BLK_DEV_CMD646 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_INITRD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_DEV_DAC960 is not set
CONFIG_PARIDE_PARPORT=y
CONFIG_PARIDE=m
# CONFIG_PARIDE_PD is not set
# CONFIG_PARIDE_PCD is not set
# CONFIG_PARIDE_PF is not set
# CONFIG_PARIDE_PT is not set
# CONFIG_PARIDE_PG is not set
# CONFIG_PARIDE_ATEN is not set
# CONFIG_PARIDE_BPCK is not set
# CONFIG_PARIDE_COMM is not set
# CONFIG_PARIDE_DSTR is not set
# CONFIG_PARIDE_FIT2 is not set
# CONFIG_PARIDE_FIT3 is not set
# CONFIG_PARIDE_EPAT is not set
# CONFIG_PARIDE_EPIA is not set
# CONFIG_PARIDE_FRIQ is not set
# CONFIG_PARIDE_FRPW is not set
# CONFIG_PARIDE_KBIC is not set
# CONFIG_PARIDE_KTTI is not set
# CONFIG_PARIDE_ON20 is not set
# CONFIG_PARIDE_ON26 is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_DEV_HD is not set
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_NETLINK=y
CONFIG_RTNETLINK=y
# CONFIG_NETLINK_DEV is not set
CONFIG_FIREWALL=y
# CONFIG_FILTER is not set
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_IP_FIREWALL is not set
# CONFIG_IP_ROUTER is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
CONFIG_IP_ALIAS=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_RARP is not set
CONFIG_SKB_LARGE=y
# CONFIG_IPV6 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_BRIDGE is not set
# CONFIG_LLC is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
# CONFIG_CPU_IS_SLOW is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
#
# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
# CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT is not set
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_PROC_STATS=y
CONFIG_AIC7XXX_RESET_DELAY=5
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
CONFIG_SCSI_IZIP_EPP16=y
CONFIG_SCSI_IZIP_SLOW_CTR=y
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_SCSI is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_ETHERTAP is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
CONFIG_EL1=m
CONFIG_EL2=m
CONFIG_ELPLUS=m
CONFIG_EL16=m
CONFIG_EL3=m
# CONFIG_3C515 is not set
CONFIG_VORTEX=m
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_RTL8139 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_EISA=y
# CONFIG_PCNET32 is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_DM9102 is not set
# CONFIG_DE4X5 is not set
# CONFIG_DEC_ELCP is not set
# CONFIG_DEC_ELCP_OLD is not set
# CONFIG_DGRS is not set
CONFIG_EEXPRESS_PRO100=y
# CONFIG_LNE390 is not set
# CONFIG_NE3210 is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SIS900 is not set
# CONFIG_ES3210 is not set
# CONFIG_EPIC100 is not set
# CONFIG_ZNET is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
CONFIG_FDDI=y
# CONFIG_DEFXX is not set
# CONFIG_HIPPI is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set
# CONFIG_NET_RADIO is not set
#
# Token ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_HOSTESS_SV11 is not set
# CONFIG_COSA is not set
# CONFIG_SEALEVEL_4021 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_COMX is not set
# CONFIG_DLCI is not set
# CONFIG_SBNI is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_UNIX98_PTYS is not set
CONFIG_PRINTER=m
# CONFIG_PRINTER_READBACK is not set
CONFIG_MOUSE=y
#
# Mice
#
# CONFIG_ATIXL_BUSMOUSE is not set
# CONFIG_BUSMOUSE is not set
# CONFIG_MS_BUSMOUSE is not set
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
#
# Joysticks
#
# CONFIG_JOYSTICK is not set
# CONFIG_QIC02_TAPE is not set
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=y
#
# Video For Linux
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DTLK is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
#
# Filesystems
#
# CONFIG_QUOTA is not set
CONFIG_AUTOFS_FS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_UMSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_MINIX_FS=y
# CONFIG_NTFS_FS is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_EFS_FS is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
CONFIG_NFS_FS=m
# CONFIG_NFSD is not set
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
# CONFIG_SMB_FS is not set
# CONFIG_NCP_FS is not set
#
# Partition Types
#
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MAC_PARTITION is not set
# CONFIG_SMD_DISKLABEL is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set
# CONFIG_MDA_CONSOLE is not set
# CONFIG_FB is not set
#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_PAS is not set
# CONFIG_SOUND_SB is not set
# CONFIG_SOUND_GUS is not set
# CONFIG_SOUND_MPU401 is not set
# CONFIG_SOUND_PSS is not set
# CONFIG_SOUND_MSS is not set
# CONFIG_SOUND_SSCAPE is not set
# CONFIG_SOUND_TRIX is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_MAD16 is not set
# CONFIG_SOUND_WAVEFRONT is not set
CONFIG_SOUND_CS4232=m
# CONFIG_SOUND_OPL3SA2 is not set
# CONFIG_SOUND_MAUI is not set
# CONFIG_SOUND_SGALAXY is not set
# CONFIG_SOUND_AD1816 is not set
# CONFIG_SOUND_OPL3SA1 is not set
# CONFIG_SOUND_SOFTOSS is not set
CONFIG_SOUND_YM3812=m
# CONFIG_SOUND_VMIDI is not set
# CONFIG_SOUND_UART6850 is not set
# CONFIG_SOUND_NM256 is not set
#
# Additional low level sound drivers
#
# CONFIG_LOWLEVEL_SOUND is not set
#
# Kernel hacking
#
# CONFIG_MAGIC_SYSRQ is not set
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Wed Mar 15 2000 - 21:00:18 EST