New IDE (ATA) drives (Seagate ST34311A) gives the following errors:
"hda: status timeout: status=0xd0 { Busy }
hda: no DRQ after issuing WRITE
ide0: reset: success"
Errors appear after disk activity but is not consistant.
Distribution is RedHat 6.1 / kernel 2.2.12 (no patches)
Tried on 2 different systems (Pentium II's) - same result.
System boots ok so can't be geometry problems.
Attached files is dmesg output, and 'hdparm -i /dev/hda' and 'hdparm
/dev/hda' outputs.
Anyone else seen this problem?
Appreciate any suggestions.
Regards
--------------0B320B54A4EEC1599AF96BED
Content-Type: text/plain; charset=us-ascii;
name="dmess.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="dmess.txt"
Linux version 2.2.12-20 (root@porky.devel.redhat.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Sep 27 10:40:35 EDT 1999
Detected 267276162 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 266.24 BogoMIPS
Memory: 62780k/65536k available (1008k kernel code, 412k reserved, 992k data, 64k init)
DENTRY hash table entries: 262144 (order: 9, 2097152 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Klamath) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfdb73
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:3a
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS not found.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: ST34311A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ST34311A, 4126MB w/256kB Cache, CHS=526/255/63
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 593.979 MB/sec
p5_mmx : 623.697 MB/sec
8regs : 459.105 MB/sec
32regs : 257.556 MB/sec
using fastest function: p5_mmx (623.697 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 >
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 64k freed
Adding Swap: 136512k swap-space (priority -1)
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
sb: dsp reset failed.
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
OPL3 not detected ff
3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xde00, 00:10:5a:39:2c:91, IRQ 9
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 7849.
MII transceiver found at address 0, status 7849.
Enabling bus-master transmits and whole-frame receives.
eth1: 3Com 3c905B Cyclone 100baseTx at 0xdc00, 00:10:5a:39:23:c3, IRQ 10
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 7849.
MII transceiver found at address 0, status 7849.
Enabling bus-master transmits and whole-frame receives.
hda: status timeout: status=0xd0 { Busy }
hda: no DRQ after issuing WRITE
ide0: reset: success
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
VFS: Disk change detected on device fd(2,0)
end_request: I/O error, dev 02:00 (floppy), sector 0
VFS: Disk change detected on device fd(2,0)
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
--------------0B320B54A4EEC1599AF96BED
Content-Type: text/plain; charset=us-ascii;
name="hdparm.i.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="hdparm.i.txt"
/dev/hda:
Model=ST34311A, FwRev=6.01, SerialNo=3BF0QNAN
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=8944/15/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=0(?), BuffSize=256kB, MaxMultSect=16, MultSect=off
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
CurCHS=526/255/63, CurSects=-135266176, LBA=yes, LBA=yes, LBAsects=8452080
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2
--------------0B320B54A4EEC1599AF96BED
Content-Type: text/plain; charset=us-ascii;
name="hdparm.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="hdparm.txt"
/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 526/255/63, sectors = 8452080, start = 0
--------------0B320B54A4EEC1599AF96BED--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/