I can't help you with everything but according to you listings below,
you forgot to compile some fonts into kernel. I'm using aty128fb too
and have to choose at least 8bb and 8x8 and 8x26 fonts (all that stuff
is in advanced section in fbcon settings). Your first two problems
I'm not able to solve (however I have only one card ;-) ...
Ferda Prantl
On Fri, Nov 26, 1999 at 10:06:18AM +0100, Gregoire FAVRE wrote:
> Hello,
>
> I have one ATI Xpert@play 8 Mb PCI and one ATI Rage Furry 32 Mb AGP, with two monitors.
>
> I have just compiled 3 2.3.29 and tried first a kernel with atyfb only: on the AGP card,
> I got:
> atyfb : 3D RAGE PRO (PQFP, PCI) [0x4750 rev 0x7e] 512K RESV, 14.31818 MHz PLL, 100 MHz MCLK
> and the screen on it turn on and show me vertical lines of blue, light blue, green and repeat.
> And the boot hangs...
>
> Secondly the kernel with atyfb and aty128fb: exactly the same result...
>
> Finaly, aty128fb only:
>
> The system boots, but can't see anything in any console other than garbage, but X just works
> as normal, I have taken those from dmesg:
>
> ...
> Rage128 BIOS located at segment C00C0000
> aty128fb: Rage128 [rev 0x2] 32M
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> Console: switching to colour frame buffer device 80x30
> fb0: ATY Rage128 frame buffer device on PCI
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> ...
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
> fbcon_setup: No support for fontwidth 8
> fbcon_setup: type 0 (aux 0, depth 8) not supported
>
> I found strange the AGP card being reported as PCI, isn't it?
>
> I just give lspci --v (in case that could help):
>
> 00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 64 set
> Region 0: Memory at e6000000 (32-bit, prefetchable)
> Capabilities: [a0] AGP version 1.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=21
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
>
> 00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 set
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: db800000-dbffffff
> Prefetchable memory behind bridge: dff00000-e5ffffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
>
> 00:04.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 set
>
> 00:04.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 set
> Region 4: I/O ports at b800
>
> 00:04.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 set
> Interrupt: pin D routed to IRQ 4
> Region 4: I/O ports at b400
>
> 00:04.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
> 00:06.0 SCSI storage controller: Adaptec AHA-2940U2/W / 7890
> Subsystem: Adaptec: Unknown device 001f
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 39 min, 25 max, 0 set, cache line size 08
> Interrupt: pin A routed to IRQ 4
> BIST result: 00
> Region 0: I/O ports at b000
> Region 1: Memory at db000000 (64-bit, non-prefetchable)
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:07.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 05)
> Subsystem: Intel Corporation 82558 10/100 with Wake on LAN
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 8 min, 56 max, 32 set, cache line size 08
> Interrupt: pin A routed to IRQ 15
> Region 0: Memory at df000000 (32-bit, prefetchable)
> Region 1: I/O ports at a800
> Region 2: Memory at da800000 (32-bit, non-prefetchable)
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- AuxPwr+ DSI+ D1+ D2+ PME+
> Status: D0 PME-Enable+ DSel=0 DScale=0 PME+
>
> 00:09.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro 215GP (rev 5c)
> Subsystem: ATI Technologies Inc: Unknown device 4750
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Region 0: Memory at dd000000 (32-bit, prefetchable) [disabled]
> Region 1: I/O ports at a400 [disabled]
> Region 2: Memory at da000000 (32-bit, non-prefetchable) [disabled]
> Expansion ROM at dcfe0000 [disabled]
>
> 00:0b.0 Multimedia video controller: Brooktree Corporation Bt848 TV with DMA push (rev 12)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 16 min, 40 max, 0 set
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at dc000000 (32-bit, prefetchable)
>
> 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RF
> Subsystem: ATI Technologies Inc: Unknown device 5246
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 8 min, 64 set, cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e0000000 (32-bit, prefetchable)
> Region 1: I/O ports at d800
> Region 2: Memory at db800000 (32-bit, non-prefetchable)
> Expansion ROM at dffe0000 [disabled]
> Capabilities: [50] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW- Rate=21
> Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=
> Capabilities: [5c] Power Management version 1
> Flags: PMEClk- AuxPwr- DSI- D1+ D2- PME-
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> If I could make something, or have done something wrong, just let me know...
>
> Please cc the answer that are not in lk to me as I am not on linux-fbdev, thanks.
>
> Greg ICQ:16624071
> ____________________________________________________________________
> http://www.unil.ch/ima/docs/Personnes/gfavre
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.rutgers.edu
> Please read the FAQ at http://www.tux.org/lkml/
--"Jen ve svych snech jsme svobodni. Po zbytek zivota potrebujeme penize." ---------------------------------- Ferdinand Prantl LVT FF UK e-mail: prantl@ff.cuni.cz www: http://www.ff.cuni.cz/~prantl ICQ: 36302930
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/