Re: 2.3.14/2.3.15pre3 boot problems
Alessandro Suardi (asuardi@uninetcom.it)
Fri, 27 Aug 1999 00:25:19 +0200
Sid Boyce wrote:
>
> P-III 450 Mhz with 128 Meg and Gigabyte GA-6BXE. Kernel 2.2.12pre8 runs
> fine.
> Disk /dev/hda: 255 heads, 63 sectors, 1313 cylinders
> Units = cylinders of 16065 * 512 bytes
>
> Device Boot Start End Blocks Id System
> /dev/hda1 * 1 3 24066 83 Linux native *** boot ***
> /dev/hda2 4 36 265072+ 82 Linux swap
> /dev/hda3 37 1313 10257502+ 83 Linux native *** root ***
>
> PIIX4: IDE controller on PCI bus 00 dev 39
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
> hda: Maxtor 91080D5, ATA DISK drive
> hdd: SANYO CRD-820P, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: Maxtor 91080D5, 10300MB w/512kB Cache, CHS=1313/255/63, UDMA
> hdd: ATAPI 20X CD-ROM drive, 256kB Cache
> Uniform CDROM driver Revision: 2.55
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> (scsi0) <Adaptec AHA-294X SCSI host adapter> found at PCI 8/0
> (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
> (scsi0) Downloading sequencer code... 406 instructions downloaded
> scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4
> <Adaptec AHA-294X SCSI host adapter>
> scsi : 1 host.
> (scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> Vendor: SEAGATE Model: ST31200N Rev: 8894
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sda at scsi0, channel 0, id 4, lun 0
> (scsi0:0:5:0) Synchronous at 3.6 Mbyte/sec, offset 15.
> Vendor: ARCHIVE Model: Python 25501-XXX Rev: 2.AH
> Type: Sequential-Access ANSI SCSI revision: 02
> Detected scsi tape st0 at scsi0, channel 0, id 5, lun 0
> scsi : detected 1 SCSI tape 1 SCSI disk total.
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 2061108 [1006 MB] [1.0
> GB]
> -----------------------------------------------------------------------------
> Partition check:
> sda: sda1
> hda: hda1 hda2 hda3
> Found PIIX4 ACPI device at 4000
> [MS-DOS FS Rel. 12, FAT 16, check=n, conv=b,uid=0,gid=0 umask=022]
> [me=0x10,cs=29835,#f=137,fs=65419,fl=5766111,ds=797624802,de=35312,data=797627025,se=9332,ts=709033984,ls=60093,vc=0,fc=4294967295]
> Transaction block size = 512
> kernel panic: VFS: Unable to mount root fs on 03:03
>
Had this on my desktop, but also a complete freeze with disk LED lit
solid on my laptop. Take out ACPI in misc devices and you should
be going. Note that both desktop and laptop here have PIIX4 ACPI
on the boards...
Ciao,
--alessandro <asuardi@uninetcom.it> <asuardi@it.oracle.com>
Linux 2.2.11/2.3.13 glibc-2.1.1-6 gcc-2.95.1 binutils-2.9.5.0.8
"They claim to walk unafraid - I'll be clumsy instead
Hold my 'love me or leave me' high" -- R.E.M.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/