Are you using a 3rd party module or the one that comes with the kernel?
On Tue, 24 Aug 1999, Saleh Jamil wrote:
Hello,
I can't get my general instruments sb1000 cable modem working after
compiling kernel 2.2.11. Afterwards I went to Clemmit Sigler's
sb1000 web page, and then I patched the 2.2.11 kernel and recompiled
it. Still, I can't connect to my ISP (Adelphia). This is the output
of what I get when starting the sb1000 under kernel 2.2.7:
Aug 24 19:05:20 TheFray kernel: PPP: version 2.3.7 (demand dialling)
Aug 24 19:05:20 TheFray kernel: PPP line discipline registered.
Aug 24 19:05:20 TheFray kernel: registered device ppp0
Aug 24 19:05:20 TheFray pppd[381]: pppd 2.3.8 started by root, uid 0
<snipped chat script output>
Aug 24 19:05:39 TheFray pppd[381]: Serial connection established.
Aug 24 19:05:39 TheFray pppd[381]: Using interface ppp0
Aug 24 19:05:39 TheFray pppd[381]: Connect: ppp0 <--> /dev/ttyS0
Aug 24 19:05:46 TheFray pppd[381]: Remote message: ^D^EM-j^B^F
Aug 24 19:05:46 TheFray kernel: PPP BSD Compression module registered
Aug 24 19:05:46 TheFray kernel: PPP Deflate Compression module registered
Aug 24 19:05:48 TheFray pppd[381]: local IP address 24.48.36.233
Aug 24 19:05:48 TheFray pppd[381]: remote IP address 10.1.65.141
Aug 24 19:05:48 TheFray kernel: cm0: sb1000 at (0x120,0x310), csn 1, S/N 0x25e58c87, IRQ 5.
Aug 24 19:05:48 TheFray kernel: sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net)
cm0 Link encap:Ethernet HWaddr 00:00:25:E5:8C:87
inet addr:24.48.36.233 P-t-P:10.1.65.141 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
Interrupt:5 Base address:0x120
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:297 errors:0 dropped:0 overruns:0 frame:0
TX packets:297 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
ppp0 Link encap:Point-to-Point Protocol
inet addr:24.48.36.233 P-t-P:10.1.65.141 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1514 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.1.65.141 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
10.1.65.141 0.0.0.0 255.255.255.255 UH 0 0 0 cm0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0
0 lo 0.0.0.0 10.1.65.141 0.0.0.0 UG 0 0 0
ppp0
And here is what I get when connecting under kernel 2.2.11 with ppp and the
patched sb1000 driver compiled:
Aug 24 19:12:58 shaybah modprobe: modprobe: Can't locate module ppp0
Aug 24 19:12:58 shaybah kernel: registered device ppp0
Aug 24 19:12:58 shaybah pppd[286]: pppd 2.3.8 started by root, uid 0
<snipped chat script output>
Aug 24 19:18:25 shaybah pppd[286]: Serial connection established.
Aug 24 19:18:25 shaybah pppd[286]: Using interface ppp0
Aug 24 19:18:25 shaybah pppd[286]: Connect: ppp0 <--> /dev/ttyS0
Aug 24 19:18:25 shaybah chat[313]: CONNECT
Aug 24 19:18:25 shaybah chat[313]: -- got it
Aug 24 19:18:29 shaybah pppd[286]: Remote message: ^D^EM-j^B^F
Aug 24 19:18:30 shaybah pppd[286]: local IP address 24.48.37.39
Aug 24 19:18:30 shaybah pppd[286]: remote IP address 10.1.65.141
Aug 24 19:18:30 shaybah kernel: cm0: sb1000 at (0x110,0x310), csn 1, S/N 0x25e58c87, IRQ 5.
Aug 24 19:18:30 shaybah kernel: sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net)
cm0 Link encap:Ethernet HWaddr 00:00:25:E5:8C:87
unspec addr:[NONE SET] P-t-P:[NONE SET] Mask:[NONE SET]
UP POINTOPOINT RUNNING NOARP MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
Interrupt:5 Base address:0x110
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
ppp0 Link encap:Point-to-Point Protocol
inet addr:24.48.37.39 P-t-P:10.1.65.141 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1514 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.1.65.141 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 10.1.65.141 0.0.0.0 UG 0 0 0 ppp0
Now in pre-2.2.11 kernels, all I did was run Clemmit's sb1000 auto-install
script, and everything worked fine. Should I re-run the auto-install script
after compiling the newer kernel? Should I compile cmconfig.c alone?
Any help would be greatly appreciated.
Saleh
-----------------------------------------------------------------------
Saleh Jamil
SJamil@Adelphia.Net
Absorb what is useful, discard what is useless....but most
importantly change what needs to be changed so that things
work better.
------------------------------------------------------------------------
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
-- Brendan W. McAdams | H: (305)859-2181 Programmer/Systems Administrator | W: (305)377-2880 Plexus InterActive | email:brendan@plexmedia.com http://www.plexmedia.com"Always listen to experts. They'll tell you what can't be done, and why. Then do it. " -- Robert A. Heinlein
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/