I have a strange problem trying to keep my alpha axpci33 up and running
i have 2 ncr 810 controlers (1 on board and 1 on the pci bus) this worked
okay until kernel version 2.2.0-final all the kernels after that keepon
comming up with this error..
aborting command due to timeout : pid 9, scsi1, channel 0, id 0, lun0 test
unit ready 00 00 00 00 00
ncr53cxx_abort pid=9 serial_number=15 serial_number_at_timeout=15
ncr53c810-1: abort ccb=fffffc0000008f40 (cancel)
SCSI host 1 is abort (pid 9) timed out - reseting
SCSI host is being reset for host 1 channel 0
and then it keeps on going..
The strange thing is that alle the kernels i tested used the same version
of the ncr53cxx scsi driver so i think the problem must be somewhere else
in the kernel... tryed kernels up to 2.2.2-pre1
Linux version 2.2.0-final (root@big-cd.bighole.iaf.nl) (gcc version 2.7.2.3) #8 Fri Jan 22 00:13:23 CET 1999
Booting on Noname using machine vector Noname
Command line: bootdevice=sda2 bootfile=vml-2.2.0-9.gz root=/dev/sda2
HWRPB cycle frequency bogus. Estimating... 166884558 Hz
Console: colour VGA+ 80x25
Calibrating delay loop... 162.53 BogoMIPS
Memory: 29840k available
POSIX conformance testing by UNIFIX
Alpha PCI BIOS32 revision 0.04
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 2.88M
FDC 0 is a National Semiconductor PC87306
ncr53c8xx: at PCI bus 0, device 6, function 0
ncr53c8xx: 53c810 detected
ncr53c8xx: at PCI bus 0, device 11, function 0
ncr53c8xx: 53c810 detected
ncr53c810-0: rev=0x01, base=0x4200000, io_port=0x8000, irq=11
ncr53c810-0: ID 7, Fast-10, Parity Checking
ncr53c810-0: restart (scsi reset).
ncr53c810-1: rev=0x01, base=0x5000000, io_port=0x8800, irq=14
ncr53c810-1: ID 7, Fast-10, Parity Checking
ncr53c810-1: restart (scsi reset).
scsi0 : ncr53c8xx - revision 3.1f
scsi1 : ncr53c8xx - revision 3.1f
scsi : 2 hosts.
ncr53c810-0-<0,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8)
Vendor: COMPAQPC Model: DSP3053LS Rev: 440F
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: QUANTUM Model: ELS42S Rev: 4.07
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 6, lun 0
ncr53c810-0-<0,0>: tagged command queue depth set to 8
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 1046532 [511 MB] [0.5 GB]
ncr53c810-0-<6,*>: SYNC transfers not supported.
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 82332 [40 MB] [0.0 GB]
At this point the other kernels start producing trouble
eth0: 3c509 at 0x340 tag 1, 10baseT port, address 00 20 af 6e d4 9c, IRQ 5.
3c509.c:1.12 6/4/97 becker@cesdis.gsfc.nasa.gov
Partition check:
sda: sda1 sda2 sda3
sdb: sdb1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 96k freed
Adding Swap: 30576k swap-space (priority -1)
Gr. Ronald Meijerink
-- ------------------------------------------------------------------------------ Ronald Meijerink ronald@bighole.iaf.nl Tel +31-534870023 GSM +31-654985709- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/