> Hi Doug, Alan,
> I am trying 2.0.36pre14 with aic7xxx to see if the scsi reset
> problem is solved.
>
> Sorry Doug, but still gives timeouts on a out of the box HP Vectra
> machine (UP). It has a 2940UW controller.
>
> I had the same problem applying 5.1.0 patches on a 2.0.35 stock kernel.
>
> Find attached the output during startup.
>
> <6>FDC 0 is a National Semiconductor PC87306
> <6>(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 9/0
> <6>(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
> <6>(scsi0) Warning - detected auto-termination
> <6>(scsi0) Please verify driver detected settings are correct.
> <6>(scsi0) If not, then please properly set the device termination
> <6>(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
> <6>(scsi0) during machine bootup.
> <6>(scsi0) Cables present (Int-50 NO, Int-68 YES, Ext-68 NO)
> <6>(scsi0) Downloading sequencer code... 419 instructions downloaded
> <4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.0/3.2.4
> <4> <Adaptec AHA-294X Ultra SCSI host adapter>
> <4>scsi : 1 host.
> <4> Vendor: FUJITSU Model: MAB3045SP Rev: 0107
> <4> Type: Direct-Access ANSI SCSI revision: 02
> <4>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> <4>scsi : detected 1 SCSI disk total.
> <6>(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
> <4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 8895370 [4343 MB]
> [4.3 GB]
> <4>Partition check:
> <4> sda: sda1 sda2 sda3
> <4>VFS: Mounted root (ext2 filesystem) readonly.
> <4>Adding Swap: 120480k swap-space (priority -1)
> <4>scsi : aborting command due to timeout : pid 692, scsi0, channel 0, id
> 0, lun 0 Read (10) 00 00 4f a0 9e 00 00 02 00
> <4>SCSI host 0 abort (pid 692) timed out - resetting
> <4>SCSI bus is being reset for host 0 channel 0.
> <6>(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
>
>
> Regards,
>
> --
> Ricardo Galli
> mailto:gallir@atlas-iap.es
> mailto:rgalli@acm.org
>
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.rutgers.edu
> Please read the FAQ at http://www.tux.org/lkml/
>
I used 2.0.36pre14 on Dual Pentium 333, 128 MB RAM, AIC7880 and when I
boot I get timeouts.
***************
Catalin BOIE
System Administrator at Deuroconsult
catab@deuroconsult.ro
http://www2.deuroconsult.ro/~catab
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/