Please help me with these problem:
Few days ago I've installed my "new" hd (conner 1080mb) in my computer. It's
splitted in three partions: 1 primary (dos fat 16) e 2 logical for linux (1
native e 1 for the swap). Both the hds are on the primary Eide channel (the
old one is a Ibm 1700mb as master, three partitions fat 16), while the cd
(Creative infra1800) is on the secondary channel as master. During the first
step of the installation with Debian 1.3 distribution I haven't problems...all
the hardware was founded (except the sound card but is a SB32AWE); the
problems start when I reboot the system for the second step of installation
(when the packets must be installed): the led of the Cd is always light, all
the commands on the front don't work and the cd seems died....I can't continue
the installation.
Obviously the cd has no problem under M$-dos and Window$.
Here is the messagges that are displayed during the boot of the second step of
installation:
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000faf50
pcibios_init : BIOS32 Service Directory entry at 0xfb3f0
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb420
Probing PCI hardware.
Warning : Unknown PCI device (102b:51a). Please read include/linux/pci.h
Warning : Unknown PCI device (121a:1). Please read include/linux/pci.h
>I suppose it's the sound card (SBAWE32)
Calibrating delay loop.. ok - 79.67 BogoMIPS
Memory: 62756k/65536k available (984k kernel code, 384k reserved, 1412k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.29 (herbert@greathan) (gcc version 2.7.2.2) #1 Mon May 26
09:25:51 EST 1997
Real Time Clock Driver v1.07
tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $
tpqic02: DMA buffers: 20 blocks, at address 0x248c00 (0x248a50)
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide0: BM-DMA at 0x9000-0x9007
ide1: BM-DMA at 0x9008-0x900f
hda: IBM-DJAA-31700, 1628MB w/96kB Cache, LBA, CHS=827/64/63
hdb: Conner Peripherals 1080MB - CFS1081A, 1032MB w/0kB Cache, LBA,
CHS=524/64/63, DMA
hdc: no response (status = 0xd0)
>Here is the bad message
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
Started kswapd v 1.4.2.2
FDC 0 is a post-1991 82077
md driver 0.35 MAX_MD_DEV=4, MAX_REAL=8
Failed initialization of WD-7000 SCSI card!
scsi0 : PPA driver version 0.26 using 8-bit mode on port 0x378.
scsi : 1 host.
Vendor: IOMEGA Model: ZIP 100 Rev: D.13
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sda at scsi0, channel 0, id 6, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sda: Write Protect is off
Partition check:
sda: sda4
hda: hda1 hda2 < hda5 hda6 >
hdb: hdb1 hdb2 < hdb5 hdb6 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 10044k swap-space
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
tty03 at 0x02e8 (irq = 3) is a 16550A
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.2.0 (dynamic channel allocation)
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
attempt to access beyond end of device
03:07: rw=0, want=1, limit=0
FAT bread failed
>What does this error means?
Please, please, help me.
Bai bii,
Gianluca.
God's in his heaven, all right with the world
The ninth, Matriel