I still get NFS messages when trying to mount remote file systems at
boot. After some time, things start to work, so it's not a big problem
(apparently?)
Also, when trying to smbmount SMB shares, I get the message:
smb_read_super: need mount version 6
While mount --version tells me 2.7f which is greate than the 2.6 the
kernel docs claim is sufficient (and which I suspect the error message
refers to) In inode.c, there's a check for an exact match, should it
perhaps be an inequality?
~kzm
------ BEGIN dmesg output ------
Memory: sized by int13 088h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
PCI: BIOS32 Service Directory structure at 0xc00fd5b0
PCI: BIOS32 Service Directory entry at 0xf6ccf
PCI: PCI BIOS revision 2.10 entry at 0xf6df0
Probing PCI hardware.
Calibrating delay loop.. ok - 53.25 BogoMIPS
Memory: 31032k/32768k available (720k kernel code, 392k reserved, 604k data, 20k init)
Swansea University Computer Society NET3.039 for Linux 2.1
NET3: Unix domain sockets 0.16 for Linux NET3.038.
Swansea University Computer Society TCP/IP for NET3.037
IP Protocols: IGMP, ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.1.62 (root@valkyrie) (gcc version 2.7.2.3) #9 Tue Nov 4 13:51:15 MET 1997
POSIX conformance testing by UNIFIX
Starting kswapd v 1.23
PS/2 auxiliary pointing device detected -- driver installed.
hda: QUANTUM TRB850A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: QUANTUM TRB850A, 810MB w/96kB Cache, LBA, CHS=823/32/63
eth0: 3c509 at 0x300 tag 1, 10baseT port, address 00 20 af f2 9d be, IRQ 10.
3c509.c:1.07 6/15/95 becker@cesdis.gsfc.nasa.gov
Partition check:
hda: hda1 hda2 < hda5 hda6 >
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 20k freed
Adding Swap: 20124k swap-space (priority -1)
Unable to load NLS charset cp437
lo UP fl=0000004b pa=0100007F/000000FF brd=FFFFFF7F dst=00000000
lo changes brd FFFFFF7F -> FFFFFF7F
eth0: Setting Rx mode to 1 addresses.
eth0 UP fl=00003043 pa=DBDE00C3/00FFFFFF brd=FFDE00C3 dst=00000000
eth0 changes brd FFDE00C3 -> FFDE00C3
route forgot to specify route netmask.
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: makesock failed, error=-111
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: no pid, 2 users??
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: makesock failed, error=-111
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: no pid, 3 users??
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: makesock failed, error=-111
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: no pid, 4 users??
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: makesock failed, error=-111
portmap: RPC call returned error 111
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
smb_read_super: need mount version 6
smb_read_super: need mount version 6