I've been running Kernel 2.0.18 for about 5 days (without any
boot) then today (1 minute ago) I got a crash. The system was frozen! And
I couldn't press CTRL+ALT+DEL. :( Then I had to power the computer off
wait some seconds and then turn it on again. My boot as ALMOST well:
-----------------------(DMESG)----------------------------------
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fb2f0
pcibios_init : BIOS32 Service Directory entry at 0xfb790
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb7c0
Probing PCI hardware.
Calibrating delay loop.. ok - 39.73 BogoMIPS
Memory: 30876k/32768k available (752k kernel code, 384k reserved, 756k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.12 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP, IPIP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.18 (root@cpu) (gcc version 2.7.0) #2 Thu Sep 5 14:01:09 EST 1996
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
Cyclom driver $Revision: 1.36.3.7A $$Date: 1996/07/27 10:25:50 $
Cyclom-Y/ISA #1: 0xd4000-0xd5fff, IRQ12, 16 channels starting from port 0.
lp: Driver configured but no interfaces found.
Floppy drive(s): fd0 is 1.44M, fd1 is 1.2M
Started kswapd v 1.4.2.2
FDC 0 is a post-1991 82077
aic7xxx: BurstLen = 0 DWDs, Latency Timer = 32 PCLKS
aic7xxx: AHA-2940 Rev B.
aic7xxx: devconfig = 0x580.
aic7xxx: Reading SEEPROM...done.
aic7xxx: Extended translation enabled.
aic7xxx: Memory check yields 16 SCBs, paging not enabled.
AHA-2940 (PCI-bus), I/O 0x6000, Mem 0xf0210000:
irq 11
bus release time 40 bclks
data fifo threshold 100%
SCSI CHANNEL A:
scsi id 7
scsi selection timeout 256 ms
scsi bus reset at power-on enabled
scsi bus parity enabled
scsi bus termination (low byte) enabled
aic7xxx: Downloading sequencer code...done.
aic7xxx: Resetting the SCSI bus...done.
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 3.4/3.2/3.1
scsi : 1 host.
scsi0: Scanning channel A for devices.
scsi0: Target 0, channel A, now synchronous at 10.0MHz, offset 15.
Vendor: QUANTUM Model: XP34301 Rev: 1071
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8410200 [4106 MB] [4.1 GB]
tunnel: version v0.2b2
PPP: version 2.2.0 (dynamic channel allocation)
TCP compression code copyright 1989 Regents of the University of California
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
ne.c:v1.10 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)
NE*000 ethercard probe at 0x300: 00 40 05 24 40 cf
eth0: NE2000 found at 0x300, using IRQ 5.
Partition check:
sda: sda1 sda2
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 40156k swap-space
fcntl_setlk() called by process 51 (lpd) with broken flock() emulation
registered device ppp0
registered device ppp1
registered device ppp2
--------------------------------------------------------------------------
Check out on the last 4 lines. :(
When it locks my system up, there were a lot of numbers and "[" and "]" on
the screen. :(
Regards,
Daniel Lafraia