>BusLogic_Probe(0x330): Status 0x30
>BusLogic_Probe(0x330): Geometry 0x55
>BusLogic_HardReset(0x330): Diagnostic Active, Status 0xB0
>BusLogic_HardReset(0x330): Diagnostic Completed, Status 0x30
>BusLogic_HardReset(0x330): Host Adapter Ready, Status 0x30
>BusLogic_Command(8D) Status = 30: 14 ==> 14: 45 DC 00 20 00 00 00 00 00 00 32 31 20 00
>BusLogic_Check(0x330): Result 14
>scsi: ***** BusLogic SCSI Driver Version 1.3.2 of 13 April 1996 *****
>scsi: Copyright 1995 by Leonard N. Zubkoff <lnz@dandelion.com>
>BusLogic_Command(04) Status = 30: 4 ==> 4: 41 41 34 32
>BusLogic_Command(0B) Status = 30: 3 ==> 3: 00 04 07
>BusLogic_Command(0D) Status = 30: 31 ==> 31: 03 00 07 04 00 00 00 00 00 00 00 00 00 00 00 00 FF 42 44 45 00 00 00 00 00 00 00 00 00 00 00
>BusLogic_Command(8D) Status = 30: 14 ==> 14: 45 DC 00 20 00 00 00 00 00 00 32 31 20 00
>BusLogic_Command(8B) Status = 30: 5 ==> 5: 34 34 78 43 20
>BusLogic_Command(84) Status = 30: 1 ==> 1: 31
>BusLogic_Command(85) Status = 30: 1 ==> 1: 20
>BusLogic_Command(91) Status = 30: 1 ==> 1: 3A
>scsi0: Configuring BusLogic Model BT-44xC VESA SCSI Host Adapter
>scsi0: Firmware Version: 4.21, I/O Address: 0x330, IRQ Channel: 11/Edge
>scsi0: DMA Channel: None, BIOS Address: 0xDC000, Host Adapter SCSI ID: 7
>scsi0: Scatter/Gather Limit: 128 of 8192 segments, Parity Checking: Enabled
>scsi0: Synchronous Initiation: Enabled, Extended Disk Translation: Disabled
>scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Disabled
>scsi0: Total Queue Depth: 100, Mailboxes: 255, Initial CCBs: 64
>scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
>scsi0: Host Adapter SCSI Bus Termination: Disabled
>scsi0: Error Recovery Strategy: Default
>BusLogic_Command(81) Status = 10: 0 ==> 0:
>BusLogic_Command(8F) Status = 10: 0 ==> 0:
>scsi0: *** BusLogic BT-44xC Initialized Successfully ***
>BusLogic_Command(24) Status = 11: 2 ==> 0:
>While configuring BusLogic Host Adapter at I/O Address 0x330:
>INQUIRE DEVICES FAILED - DETACHING
>ADDITIONAL FAILURE INFO - Command Invalid
>BusLogic_Probe(0x334): Status 0xFF
>BusLogic_Probe(0x230): Status 0xFF
>BusLogic_Probe(0x234): Status 0xFF
>BusLogic_Probe(0x130): Status 0xFF
>BusLogic_Probe(0x134): Status 0xFF
>scsi : 0 hosts.
>scsi : detected total.
>Partition check:
>VFS: Cannot open root device 08:01
>Kernel panic: VFS: Unable to mount root fs on 08:01
----_--__---_-_-_-__--_-__-__---_-_----_--_-_---_---_----
_/ TANAKA Yoshitomo _//
/ Suginami-ku Tokyo, Japan _// serow@silkwood.rim.or.jp