Re: [PATCH v6 10/11] riscv: dts: add initial canmv-k230 and k230-evb dts

From: Icenowy Zheng
Date: Sun Mar 24 2024 - 12:25:47 EST


在 2024-03-23星期六的 20:12 +0800,Yangyu Chen写道:
> Add initial dts for CanMV-K230 and K230-EVB powered by Canaan
> Kendryte
> K230 SoC [1].
>
> Some key consideration:
>
> - Only place BigCore which is 1.6GHz RV64GCBV
>
> The existence of cache coherence between the two cores remains
> unknown
> since they have dedicated L2 caches. And the factory SDK uses it for
> other OS by default. I don't know whether the two CPUs on K230 SoC
> can be used in one system. So only place BigCore here.
>
> Meanwhile, although docs from Canaan said 1.6GHz Core with Vector is
> CPU1, the CSR.MHARTID of this core is 0.
>
> - Support for "zba" "zbb" "zbc" "zbs" are tested by hand
>
> The user manual of C908 from T-Head does not document it
> specifically.
> It just said it supports B extension V1.0. [2]
>
> I have tested it by using this [3] which attempts to execute
> "add.uw",
> "andn", "clmulr", "bclr" and they doesn't traps on K230. But on
> JH7110,
> "clmulr" and "bclr" will trap.
>
> - Support for "zicbom" is tested by hand
>
> Have tested with some out-of-tree drivers from [4] that need DMA and
> they
> do not come to the dts currently.
>
> - Cache parameters are inferred from T-Head docs [2] and Canaan docs
> [1]
>
> L1i: 32KB, VIPT 4-Way set-associative, 64B Cacheline
> L1d: 32KB, VIPT 4-Way set-associative, 64B Cacheline
> L2: 256KB, PIPT 16-way set-associative, 64B Cacheline
>
> The numbers of cache sets are calculated from these parameters.
>
> - MMU only supports Sv39
>
> The T-Head docs [2] say the C908 core can be configured to support
> Sv48 and
> Sv39 or only Sv39. On K230, I tried to write "riscv,sv48" on mmu-type
> in
> dts and boot the mainline kernel. However, it failed during the
> kernel
> probe and fell back to Sv39. I also tested it on M-Mode software,
> writing
> Sv48 to satp.mode will not trap but will leave the CSR unchanged.
> While
> writing Sv39, it will take effect. It shows that this CPU does not
> support
> Sv48.
>
> - Svpbmt and T-Head MAEE both supported
>
> T-Head C908 does support both Svpbmt and T-Head MAEE for page-based
> memory
> attributes and is controlled by BIT(21) on CSR.MXSTATUS. The Svpbmt
> is used
> here for mainline kernel support for K230. If the kernel wants to use
> Svpbmt, the M-Mode software should unset BIT(21) of CSR.MXSTATUS
> before
> entering the S-Mode kernel. Otherwise, the kernel will not boot, as 0
> on
> T-Head MAEE is NonCachable Memory. Once the kernel switches from bare
> metal
> to Sv39, It will lose dirty cache line modifications that haven't
> been
> written back to the memory.
>
> [1]
> https://developer.canaan-creative.com/k230/dev/zh/00_hardware/K230_datasheet.html#chapter-1-introduction
> [2]
> https://occ-intl-prod.oss-ap-southeast-1.aliyuncs.com/resource//1699268369347/XuanTie-C908-UserManual.pdf
> [3] https://github.com/cyyself/rvb_test
> [4] https://github.com/cyyself/linux/tree/k230-mainline
>
> Signed-off-by: Yangyu Chen <cyy@xxxxxxxxxxxx>
> ---
>  arch/riscv/boot/dts/canaan/Makefile       |   2 +
>  arch/riscv/boot/dts/canaan/k230-canmv.dts |  24 ++++
>  arch/riscv/boot/dts/canaan/k230-evb.dts   |  24 ++++
>  arch/riscv/boot/dts/canaan/k230.dtsi      | 140
> ++++++++++++++++++++++
>  4 files changed, 190 insertions(+)
>  create mode 100644 arch/riscv/boot/dts/canaan/k230-canmv.dts
>  create mode 100644 arch/riscv/boot/dts/canaan/k230-evb.dts
>  create mode 100644 arch/riscv/boot/dts/canaan/k230.dtsi
>
> diff --git a/arch/riscv/boot/dts/canaan/Makefile
> b/arch/riscv/boot/dts/canaan/Makefile
> index 987d1f0c41f0..7d54ea5c6f3d 100644
> --- a/arch/riscv/boot/dts/canaan/Makefile
> +++ b/arch/riscv/boot/dts/canaan/Makefile
> @@ -1,6 +1,8 @@
>  # SPDX-License-Identifier: GPL-2.0
>  dtb-$(CONFIG_ARCH_CANAAN) += canaan_kd233.dtb
>  dtb-$(CONFIG_ARCH_CANAAN) += k210_generic.dtb
> +dtb-$(CONFIG_ARCH_CANAAN) += k230-canmv.dtb
> +dtb-$(CONFIG_ARCH_CANAAN) += k230-evb.dtb

BTW did you test on K230 EVB? I think only CanMV is currently publicly
available.

If K230 EVB support is not tested, I suggest not adding it.

>  dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maix_bit.dtb
>  dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maix_dock.dtb
>  dtb-$(CONFIG_ARCH_CANAAN) += sipeed_maix_go.dtb
> diff --git a/arch/riscv/boot/dts/canaan/k230-canmv.dts
> b/arch/riscv/boot/dts/canaan/k230-canmv.dts
> new file mode 100644
> index 000000000000..9565915cead6
> --- /dev/null
> +++ b/arch/riscv/boot/dts/canaan/k230-canmv.dts
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2024 Yangyu Chen <cyy@xxxxxxxxxxxx>
> + */
> +
> +#include "k230.dtsi"
> +
> +/ {
> +       model = "Canaan CanMV-K230";
> +       compatible = "canaan,canmv-k230", "canaan,kendryte-k230";
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       ddr: memory@0 {
> +               device_type = "memory";
> +               reg = <0x0 0x0 0x0 0x20000000>;
> +       };
> +};
> +
> +&uart0 {
> +       status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/canaan/k230-evb.dts
> b/arch/riscv/boot/dts/canaan/k230-evb.dts
> new file mode 100644
> index 000000000000..f898b8e62368
> --- /dev/null
> +++ b/arch/riscv/boot/dts/canaan/k230-evb.dts
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2024 Yangyu Chen <cyy@xxxxxxxxxxxx>
> + */
> +
> +#include "k230.dtsi"
> +
> +/ {
> +       model = "Kendryte K230 EVB";
> +       compatible = "canaan,k230-usip-lp3-evb", "canaan,kendryte-
> k230";
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       ddr: memory@0 {
> +               device_type = "memory";
> +               reg = <0x0 0x0 0x0 0x20000000>;
> +       };
> +};
> +
> +&uart0 {
> +       status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/canaan/k230.dtsi
> b/arch/riscv/boot/dts/canaan/k230.dtsi
> new file mode 100644
> index 000000000000..7da49498945e
> --- /dev/null
> +++ b/arch/riscv/boot/dts/canaan/k230.dtsi
> @@ -0,0 +1,140 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2024 Yangyu Chen <cyy@xxxxxxxxxxxx>
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/dts-v1/;
> +/ {
> +       #address-cells = <2>;
> +       #size-cells = <2>;
> +       compatible = "canaan,kendryte-k230";
> +
> +       aliases {
> +               serial0 = &uart0;
> +       };
> +
> +       cpus {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               timebase-frequency = <27000000>;
> +
> +               cpu@0 {
> +                       compatible = "thead,c908", "riscv";
> +                       device_type = "cpu";
> +                       reg = <0>;
> +                       riscv,isa =
> "rv64imafdcv_zba_zbb_zbc_zbs_zicbom_svpbmt";
> +                       riscv,isa-base = "rv64i";
> +                       riscv,isa-extensions = "i", "m", "a", "f",
> "d", "c", "v", "zba", "zbb",
> +                                              "zbc", "zbs",
> "zicbom", "zicntr", "zicsr",
> +                                              "zifencei", "zihpm",
> "svpbmt";
> +                       riscv,cbom-block-size = <64>;
> +                       d-cache-block-size = <64>;
> +                       d-cache-sets = <128>;
> +                       d-cache-size = <32768>;
> +                       i-cache-block-size = <64>;
> +                       i-cache-sets = <128>;
> +                       i-cache-size = <32768>;
> +                       next-level-cache = <&l2_cache>;
> +                       mmu-type = "riscv,sv39";
> +
> +                       cpu0_intc: interrupt-controller {
> +                               compatible = "riscv,cpu-intc";
> +                               interrupt-controller;
> +                               #interrupt-cells = <1>;
> +                       };
> +               };
> +
> +               l2_cache: l2-cache {
> +                       compatible = "cache";
> +                       cache-block-size = <64>;
> +                       cache-level = <2>;
> +                       cache-size = <262144>;
> +                       cache-sets = <256>;
> +                       cache-unified;
> +               };
> +       };
> +
> +       apb_clk: apb-clk-clock {
> +               compatible = "fixed-clock";
> +               clock-frequency = <50000000>;
> +               clock-output-names = "apb_clk";
> +               #clock-cells = <0>;
> +       };
> +
> +       soc {
> +               compatible = "simple-bus";
> +               interrupt-parent = <&plic>;
> +               #address-cells = <2>;
> +               #size-cells = <2>;
> +               dma-noncoherent;
> +               ranges;
> +
> +               plic: interrupt-controller@f00000000 {
> +                       compatible = "canaan,k230-plic" ,"thead,c900-
> plic";
> +                       reg = <0xf 0x00000000 0x0 0x04000000>;
> +                       interrupts-extended = <&cpu0_intc 11>,
> <&cpu0_intc 9>;
> +                       interrupt-controller;
> +                       #address-cells = <0>;
> +                       #interrupt-cells = <2>;
> +                       riscv,ndev = <208>;
> +               };
> +
> +               clint: timer@f04000000 {
> +                       compatible = "canaan,k230-clint",
> "thead,c900-clint";
> +                       reg = <0xf 0x04000000 0x0 0x00010000>;
> +                       interrupts-extended = <&cpu0_intc 3>,
> <&cpu0_intc 7>;
> +               };
> +
> +               uart0: serial@91400000 {
> +                       compatible = "snps,dw-apb-uart";
> +                       reg = <0x0 0x91400000 0x0 0x1000>;
> +                       clocks = <&apb_clk>;
> +                       interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
> +                       reg-io-width = <4>;
> +                       reg-shift = <2>;
> +                       status = "disabled";
> +               };
> +
> +               uart1: serial@91401000 {
> +                       compatible = "snps,dw-apb-uart";
> +                       reg = <0x0 0x91401000 0x0 0x1000>;
> +                       clocks = <&apb_clk>;
> +                       interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
> +                       reg-io-width = <4>;
> +                       reg-shift = <2>;
> +                       status = "disabled";
> +               };
> +
> +               uart2: serial@91402000 {
> +                       compatible = "snps,dw-apb-uart";
> +                       reg = <0x0 0x91402000 0x0 0x1000>;
> +                       clocks = <&apb_clk>;
> +                       interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
> +                       reg-io-width = <4>;
> +                       reg-shift = <2>;
> +                       status = "disabled";
> +               };
> +
> +               uart3: serial@91403000 {
> +                       compatible = "snps,dw-apb-uart";
> +                       reg = <0x0 0x91403000 0x0 0x1000>;
> +                       clocks = <&apb_clk>;
> +                       interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
> +                       reg-io-width = <4>;
> +                       reg-shift = <2>;
> +                       status = "disabled";
> +               };
> +
> +               uart4: serial@91404000 {
> +                       compatible = "snps,dw-apb-uart";
> +                       reg = <0x0 0x91404000 0x0 0x1000>;
> +                       clocks = <&apb_clk>;
> +                       interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
> +                       reg-io-width = <4>;
> +                       reg-shift = <2>;
> +                       status = "disabled";
> +               };
> +       };
> +};