Re: [PATCH 2/2] ARM: dts: sun5i: Add PocketBook 614 Plus support

From: hitechshell
Date: Thu Mar 14 2024 - 14:49:57 EST

On Thu, Mar 14, 2024 at 06:14:48PM +0100, Jernej Škrabec wrote:
> Hi Denis!
>
> Dne četrtek, 14. marec 2024 ob 16:53:06 CET je Denis Burkov napisal(a):
> > What works:
> >
> > - Serial console
> > - mmc0, mmc2 (both microSD card slots on the board)
> > - All buttons (gpio and lradc based)
> > - Power LED
> > - PMIC
> > - RTC
> > - USB OTG/gadgets mode
> >
> > Signed-off-by: Denis Burkov <hitechshell@xxxxxxx>
> > ---
> > arch/arm/boot/dts/allwinner/Makefile | 2 +
> > .../sun5i-a13-pocketbook-614-plus.dts | 254 ++++++++++++++++++
> > 2 files changed, 256 insertions(+)
> > create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> >
> > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> > index 2d26c3397f14..fe321865beed 100644
> > --- a/arch/arm/boot/dts/allwinner/Makefile
> > +++ b/arch/arm/boot/dts/allwinner/Makefile
> > @@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> > sun5i-a13-olinuxino.dtb \
> > sun5i-a13-olinuxino-micro.dtb \
> > sun5i-a13-pocketbook-touch-lux-3.dtb \
> > + sun5i-a13-pocketbook-614-plus.dtb \
> > sun5i-a13-q8-tablet.dtb \
> > sun5i-a13-utoo-p66.dtb \
> > sun5i-gr8-chip-pro.dtb \
> > @@ -82,6 +83,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> > sun5i-a13-olinuxino.dtb \
> > sun5i-a13-olinuxino-micro.dtb \
> > sun5i-a13-pocketbook-touch-lux-3.dtb \
> > + sun5i-a13-pocketbook-614-plus.dtb \
> > sun5i-a13-q8-tablet.dtb \
> > sun5i-a13-utoo-p66.dtb \
> > sun5i-gr8-chip-pro.dtb \
>
> This merge artefact. Can you add patch before this one and remove duplicate definitions?
>
Sorry, I didn't quite understand. Should I remove the duplicate block in a separate commit? or enable this one?
> > diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > new file mode 100644
> > index 000000000000..89898fa16ff7
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > @@ -0,0 +1,254 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2024 Denis Burkov <hitechshell@xxxxxxx>
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun5i-a13.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
>
> Extra empty line here.
>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +
> > +/ {
> > + model = "PocketBook 614 Plus";
> > + compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
> > +
> > + aliases {
> > + serial0 = &uart1;
> > + i2c0 = &i2c0;
> > + i2c1 = &i2c1;
> > + i2c2 = &i2c2;
> > + rtc0 = &pcf8563;
>
> Please drop aliases except serial0.
>
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&led_pins_pocketbook>;
>
> Drop pinctrl nodes. GPIOs don't need them.
>
> > +
> > + led {
> > + gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
> > + default-state = "on";
>
> Add additional properties, like function and color.
>
> > + };
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + autorepeat;
>
> Why is autorepeat needed?
>
> > + label = "GPIO Keys";
>
> I guess label is self evident and not needed?
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pocketbook_btn_pins>;
>
> Again, GPIOs don't need pinctrl nodes. I know that you specified pull up, but
> please try without. Other boards have same design and it's not needed.
>
> > +
> > + key-right {
> > + label = "Right";
> > + linux,code = <KEY_NEXT>;
> > + gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
> > + };
> > +
> > + key-left {
> > + label = "Left";
> > + linux,code = <KEY_PREVIOUS>;
> > + gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
> > + };
> > + };
> > +
> > + reg_3v3_mmc0: regulator-mmc0 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vdd-mmc0";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pocketbook_reg_mmc0_pins>;
>
> again, pinctrl not needed.
>
> > + gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
> > + vin-supply = <&reg_vcc3v3>;
> > + };
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <&reg_dcdc2>;
> > +};
> > +
> > +&ehci0 {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +
> > + axp209: pmic@34 {
> > + compatible = "x-powers,axp209";
> > + reg = <0x34>;
> > + interrupts = <0>;
> > + };
> > +};
> > +
> > +#include "axp209.dtsi"
> > +
> > +&i2c1 {
> > + status = "okay";
> > +
> > + pcf8563: rtc@51 {
> > + compatible = "nxp,pcf8563";
> > + reg = <0x51>;
> > + #clock-cells = <0>;
> > + };
> > +};
> > +
> > +&i2c2 {
> > + status = "okay";
> > +
> > + /* Touchpanel is connected here. */
>
> Any reason why don't you specify touch panel device here?
>
My mistake, I copied this node from another device. This device does not have a touchpanel at all.
> > +};
> > +
> > +&lradc {
> > + vref-supply = <&reg_ldo2>;
> > + status = "okay";
> > +
> > + button-300 {
> > + label = "Down";
> > + linux,code = <KEY_DOWN>;
> > + channel = <0>;
> > + voltage = <300000>;
> > + };
> > +
> > + button-700 {
> > + label = "Up";
> > + linux,code = <KEY_UP>;
> > + channel = <0>;
> > + voltage = <700000>;
> > + };
> > +
> > + button-1000 {
> > + label = "Left";
> > + linux,code = <KEY_LEFT>;
> > + channel = <0>;
> > + voltage = <1000000>;
> > + };
> > +
> > + button-1200 {
> > + label = "Menu";
> > + linux,code = <KEY_MENU>;
> > + channel = <0>;
> > + voltage = <1200000>;
> > + };
> > +
> > + button-1500 {
> > + label = "Right";
> > + linux,code = <KEY_RIGHT>;
> > + channel = <0>;
> > + voltage = <1500000>;
> > + };
> > +};
> > +
> > +&mmc0 {
> > + vmmc-supply = <&reg_3v3_mmc0>;
> > + bus-width = <4>;
> > + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
> > + status = "okay";
> > +};
> > +
> > +&mmc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc2_4bit_pc_pins>;
> > + vmmc-supply = <&reg_vcc3v3>;
> > + bus-width = <4>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&ohci0 {
> > + status = "okay";
> > +};
> > +
> > +&otg_sram {
> > + status = "okay";
> > +};
> > +
> > +&pio {
> > + led_pins_pocketbook: led-pin {
> > + pins = "PE8";
> > + function = "gpio_out";
> > + };
> > + pocketbook_btn_pins: btn-pins {
> > + pins = "PG9", "PG10";
> > + function = "gpio_in";
> > + bias-pull-up;
> > + };
> > + pocketbook_reg_mmc0_pins: reg-mmc0-pins {
> > + pins = "PE4";
> > + function = "gpio_out";
> > + };
> > +};
>
> Whole PIO node can be dropped.
>
> Best regards,
> Jernej
>
> > +
> > +&reg_dcdc2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-name = "vdd-cpu";
> > +};
> > +
> > +&reg_dcdc3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1400000>;
> > + regulator-name = "vdd-int-dll";
> > +};
> > +
> > +&reg_ldo1 {
> > + regulator-name = "vdd-rtc";
> > +};
> > +
> > +&reg_ldo2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-name = "avcc";
> > +};
> > +
> > +&reg_ldo3 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi";
> > +};
> > +
> > +&reg_usb0_vbus {
> > + status = "okay";
> > + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> > +};
> > +
> > +&reg_usb1_vbus {
> > + gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_pg_pins>;
> > + status = "okay";
> > +};
> > +
> > +&usb_otg {
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usb_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&battery_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
> > + usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
> > + usb0_vbus-supply = <&reg_usb0_vbus>;
> > + usb1_vbus-supply = <&reg_usb1_vbus>;
> > + status = "okay";
> > +};
> >
>
>
>
>
Yes, everything works without pincrtl. One guy told me that I need to specify pinctrl for each pin used.
Thanks for the review.
Best regards,
Denis