Re: [PATCH v2 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

From: Caleb Connolly
Date: Wed Mar 13 2024 - 08:55:51 EST

Hi Sumit,

On 13/03/2024 12:30, Sumit Garg wrote:
> Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> Box Core board based on the Qualcomm APQ8016E SoC.
>
> Support for Schneider Electric HMIBSC. Features:
> - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
> - 1GiB RAM
> - 8GiB eMMC, SD slot
> - WiFi and Bluetooth
> - 2x Host, 1x Device USB port
> - HDMI
> - Discrete TPM2 chip over SPI
> - USB ethernet adaptors (soldered)
>
> Co-developed-by: Jagdish Gediya <jagdish.gediya@xxxxxxxxxx>
> Signed-off-by: Jagdish Gediya <jagdish.gediya@xxxxxxxxxx>
> Signed-off-by: Sumit Garg <sumit.garg@xxxxxxxxxx>
Reviewed-by: Caleb Connolly <caleb.connolly@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/apq8016-schneider-hmibsc.dts | 519 ++++++++++++++++++
> 2 files changed, 520 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 39889d5f8e12..ad55e52e950b 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -5,6 +5,7 @@ apq8016-sbc-usb-host-dtbs := apq8016-sbc.dtb apq8016-sbc-usb-host.dtbo
>
> dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-usb-host.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc-d3-camera-mezzanine.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += apq8016-schneider-hmibsc.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
> new file mode 100644
> index 000000000000..2f6d394feb87
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
> @@ -0,0 +1,519 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2024, Linaro Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8916-pm8916.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
> +#include <dt-bindings/sound/apq8016-lpass.h>
> +
> +/ {
> + model = "Schneider Electric HMIBSC Board";
> + compatible = "schneider,apq8016-hmibsc", "qcom,apq8016";
> +
> + aliases {
> + mmc0 = &sdhc_1; /* eMMC */
> + mmc1 = &sdhc_2; /* SD card */
> + serial0 = &blsp_uart1;
> + serial1 = &blsp_uart2;
> + usid0 = &pm8916_0;
> + i2c1 = &blsp_i2c6;
> + i2c3 = &blsp_i2c4;
> + i2c4 = &blsp_i2c3;
> + spi0 = &blsp_spi5;
> + };
> +
> + chosen {
> + stdout-path = "serial0";
> + };
> +
> + memory@80000000 {
> + reg = <0 0x80000000 0 0x40000000>;
> + };
> +
> + reserved-memory {
> + ramoops@bff00000 {
> + compatible = "ramoops";
> + reg = <0x0 0xbff00000 0x0 0x100000>;
> +
> + record-size = <0x20000>;
> + console-size = <0x20000>;
> + ftrace-size = <0x20000>;
> + };
> + };
> +
> + usb2513 {
> + compatible = "smsc,usb3503";
> + reset-gpios = <&pm8916_gpios 1 GPIO_ACTIVE_LOW>;
> + initial-mode = <1>;
> + };
> +
> + usb_id: usb-id {
> + compatible = "linux,extcon-usb-gpio";
> + id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_id_default>;
> + };
> +
> + hdmi-out {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con: endpoint {
> + remote-endpoint = <&adv7533_out>;
> + };
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&msm_key_volp_n_default>;
> +
> + button {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + leds {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pm8916_mpps_leds>;
> +
> + compatible = "gpio-leds";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + led@5 {
> + reg = <5>;
> + label = "apq8016-hmibsc:green:wlan";
> + function = LED_FUNCTION_WLAN;
> + color = <LED_COLOR_ID_YELLOW>;
> + gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> +
> + led@6 {
> + reg = <6>;
> + label = "apq8016-hmibsc:yellow:bt";
> + function = LED_FUNCTION_BLUETOOTH;
> + color = <LED_COLOR_ID_BLUE>;
> + gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "bluetooth-power";
> + default-state = "off";
> + };
> + };
> +};
> +
> +&blsp_i2c3 {
> + status = "okay";
> +
> + eeprom@50 {
> + compatible = "atmel,24c32";
> + reg = <0x50>;
> + };
> +};
> +
> +&blsp_i2c4 {
> + status = "okay";
> +
> + adv_bridge: bridge@39 {
> + status = "okay";
> +
> + compatible = "adi,adv7533";
> + reg = <0x39>;
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
> +
> + adi,dsi-lanes = <4>;
> + clocks = <&rpmcc RPM_SMD_BB_CLK2>;
> + clock-names = "cec";
> +
> + pd-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
> +
> + avdd-supply = <&pm8916_l6>;
> + a2vdd-supply = <&pm8916_l6>;
> + dvdd-supply = <&pm8916_l6>;
> + pvdd-supply = <&pm8916_l6>;
> + v1p2-supply = <&pm8916_l6>;
> + v3p3-supply = <&pm8916_l17>;
> +
> + pinctrl-names = "default","sleep";
> + pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
> + pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
> + #sound-dai-cells = <1>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + adv7533_in: endpoint {
> + remote-endpoint = <&mdss_dsi0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + adv7533_out: endpoint {
> + remote-endpoint = <&hdmi_con>;
> + };
> + };
> + };
> + };
> +};
> +
> +&blsp_i2c6 {
> + status = "okay";
> +
> + rtc@30 {
> + compatible = "sii,s35390a";
> + reg = <0x30>;
> + };
> +
> + eeprom@50 {
> + compatible = "atmel,24c256";
> + reg = <0x50>;
> + };
> +};
> +
> +&blsp_spi5 {
> + status = "okay";
> + cs-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
> +
> + tpm@0 {
> + compatible = "tcg,tpm_tis-spi";
> + reg = <0>;
> + spi-max-frequency = <500000>;
> + };
> +};
> +
> +&blsp_uart1 {
> + status = "okay";
> + label = "UART0";
> +};
> +
> +&blsp_uart2 {
> + status = "okay";
> + label = "UART1";
> +};
> +
> +&lpass {
> + status = "okay";
> +};
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&mdss_dsi0_out {
> + data-lanes = <0 1 2 3>;
> + remote-endpoint = <&adv7533_in>;
> +};
> +
> +&pm8916_codec {
> + status = "okay";
> + qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
> + qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
> +};
> +
> +&pm8916_resin {
> + status = "okay";
> + linux,code = <KEY_POWER>;
> +};
> +
> +&pm8916_rpm_regulators {
> + pm8916_l17: l17 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +};
> +
> +&sdhc_1 {
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
> + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
> +
> + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
> +};
> +
> +&sound {
> + status = "okay";
> +
> + pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
> + pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
> + pinctrl-names = "default", "sleep";
> + model = "DB410c";
> + audio-routing =
> + "AMIC2", "MIC BIAS Internal2",
> + "AMIC3", "MIC BIAS External1";
> +
> + quaternary-dai-link {
> + link-name = "ADV7533";
> + cpu {
> + sound-dai = <&lpass MI2S_QUATERNARY>;
> + };
> + codec {
> + sound-dai = <&adv_bridge 0>;
> + };
> + };
> +
> + primary-dai-link {
> + link-name = "WCD";
> + cpu {
> + sound-dai = <&lpass MI2S_PRIMARY>;
> + };
> + codec {
> + sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
> + };
> + };
> +
> + tertiary-dai-link {
> + link-name = "WCD-Capture";
> + cpu {
> + sound-dai = <&lpass MI2S_TERTIARY>;
> + };
> + codec {
> + sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
> + };
> + };
> +};
> +
> +&usb {
> + status = "okay";
> + extcon = <&usb_id>, <&usb_id>;
> +
> + pinctrl-names = "default", "device";
> + pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
> + pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
> +};
> +
> +&usb_hs_phy {
> + extcon = <&usb_id>;
> +};
> +
> +&wcnss {
> + status = "okay";
> + firmware-name = "qcom/apq8016/wcnss.mbn";
> +};
> +
> +&wcnss_ctrl {
> + firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
> +};
> +
> +&wcnss_iris {
> + compatible = "qcom,wcn3620";
> +};
> +
> +&wcnss_mem {
> + status = "okay";
> +};
> +
> +/* Enable CoreSight */
> +&cti0 { status = "okay"; };
> +&cti1 { status = "okay"; };
> +&cti12 { status = "okay"; };
> +&cti13 { status = "okay"; };
> +&cti14 { status = "okay"; };
> +&cti15 { status = "okay"; };
> +&debug0 { status = "okay"; };
> +&debug1 { status = "okay"; };
> +&debug2 { status = "okay"; };
> +&debug3 { status = "okay"; };
> +&etf { status = "okay"; };
> +&etm0 { status = "okay"; };
> +&etm1 { status = "okay"; };
> +&etm2 { status = "okay"; };
> +&etm3 { status = "okay"; };
> +&etr { status = "okay"; };
> +&funnel0 { status = "okay"; };
> +&funnel1 { status = "okay"; };
> +&replicator { status = "okay"; };
> +&stm { status = "okay"; };
> +&tpiu { status = "okay"; };
> +
> +/*
> + * 2mA drive strength is not enough when connecting multiple
> + * I2C devices with different pull up resistors.
> + */
> +
> +&blsp_i2c4_default {
> + drive-strength = <16>;
> +};
> +
> +&blsp_i2c6_default {
> + drive-strength = <16>;
> +};
> +
> +&tlmm {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_mux0_rs232_high &uart1_mux1_rs232_low>;
> +
> + sdc2_cd_default: sdc2-cd-default-state {
> + pins = "gpio38";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + usb_id_default: usb-id-default-state {
> + pins = "gpio110";
> + function = "gpio";
> +
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + adv7533_int_active: adv533-int-active-state {
> + pins = "gpio31";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + adv7533_int_suspend: adv7533-int-suspend-state {
> + pins = "gpio31";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + adv7533_switch_active: adv7533-switch-active-state {
> + pins = "gpio32";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + adv7533_switch_suspend: adv7533-switch-suspend-state {
> + pins = "gpio32";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + msm_key_volp_n_default: msm-key-volp-n-default-state {
> + pins = "gpio107";
> + function = "gpio";
> +
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + /*
> + * UART1 being the debug console supports various modes of
> + * operation (RS-232/485/422) controlled via GPIOs configured
> + * mux as follows:
> + *
> + * gpio100 gpio99 UART mode
> + * 0 0 loopback
> + * 0 1 RS-232
> + * 1 0 RS-485
> + * 1 1 RS-422
> + *
> + * The default mode configured here is RS-232 mode.
> + */
> + uart1_mux0_rs232_high: uart1-mux0-rs232-state {
> + bootph-all;
> + pins = "gpio99";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> +
> + uart1_mux1_rs232_low: uart1-mux1-rs232-state {
> + bootph-all;
> + pins = "gpio100";
> + function = "gpio";
> +
> + drive-strength = <16>;
> + bias-disable;
> + output-low;
> + };
> +};
> +
> +&pm8916_gpios {
> + gpio-line-names =
> + "USB_HUB_RESET_N_PM",
> + "USB_SW_SEL_PM",
> + "NC",
> + "NC";
> +
> + usb_hub_reset_pm: usb-hub-reset-pm-state {
> + pins = "gpio1";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + input-disable;
> + output-high;
> + };
> +
> + usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
> + pins = "gpio1";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + output-low;
> + };
> +
> + usb_sw_sel_pm: usb-sw-sel-pm-state {
> + pins = "gpio2";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + power-source = <PM8916_GPIO_VPH>;
> + input-disable;
> + output-high;
> + };
> +
> + usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
> + pins = "gpio2";
> + function = PMIC_GPIO_FUNC_NORMAL;
> +
> + power-source = <PM8916_GPIO_VPH>;
> + input-disable;
> + output-low;
> + };
> +};
> +
> +&pm8916_mpps {
> + gpio-line-names =
> + "NC",
> + "WLAN_LED_CTRL",
> + "BT_LED_CTRL",
> + "NC";
> +
> + pm8916_mpps_leds: pm8916-mpps-state {
> + pins = "mpp2", "mpp3";
> + function = "digital";
> +
> + output-low;
> + };
> +};
> +
> +&blsp_uart1_default {
> + bootph-all;
> +};

--
// Caleb (they/them)