[PATCH v1] arm64: dts: ti: verdin-am62: use SD1 CD as GPIO

[Francesco Dolcini]

From: Francesco Dolcini <francesco.dolcini@xxxxxxxxxxx>

TI SDHCI IP has a hardware debounce timer of 1 second as described in
commit 7ca0f166f5b2 ("mmc: sdhci_am654: Add workaround for card detect
debounce timer"), because of this the boot time increases of up to 1
second.

Workaround the issue the same way that is done on
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts, using the SD1 CD as
GPIO.

Suggested-by: Nishanth Menon <nm@xxxxxx>
Reported-by: João Paulo Silva Gonçalves <joao.goncalves@xxxxxxxxxxx>
Closes: https://lore.kernel.org/all/0e81af80de3d55e72f79af83fa5db87f5c9938f8.camel@xxxxxxxxxxx/
Signed-off-by: Francesco Dolcini <francesco.dolcini@xxxxxxxxxxx>
---
 arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi b/arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi
index e8d8857ad51f..a9bf2c17f95a 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi
@@ -457,6 +457,13 @@ AM62X_IOPAD(0x01c4, PIN_INPUT, 7) /* (B14) SPI0_D1.GPIO1_19 */ /* SODIMM 161 */
 		>;
 	};
 
+	/* Verdin SD_1_CD# as GPIO */
+	pinctrl_sd1_cd_gpio: main-gpio1-48-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 7) /* (D17) MMC1_SDCD.GPIO1_48 */ /* SODIMM 84 */
+		>;
+	};
+
 	/* Verdin DSI_1_INT# (pulled-up as active-low) */
 	pinctrl_dsi1_int: main-gpio1-49-default-pins {
 		pinctrl-single,pins = <
@@ -571,7 +578,6 @@ AM62X_IOPAD(0x230, PIN_INPUT,        0) /* (A22) MMC1_DAT0 */ /* SODIMM 80 */
 			AM62X_IOPAD(0x22c, PIN_INPUT,        0) /* (B21) MMC1_DAT1 */ /* SODIMM 82 */
 			AM62X_IOPAD(0x228, PIN_INPUT,        0) /* (C21) MMC1_DAT2 */ /* SODIMM 70 */
 			AM62X_IOPAD(0x224, PIN_INPUT,        0) /* (D22) MMC1_DAT3 */ /* SODIMM 72 */
-			AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 0) /* (D17) MMC1_SDCD */ /* SODIMM 84 */
 		>;
 	};
 
@@ -1441,8 +1447,10 @@ &sdhci0 {
 /* Verdin SD_1 */
 &sdhci1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sdhci1>;
+	pinctrl-0 = <&pinctrl_sdhci1>, <&pinctrl_sd1_cd_gpio>;
+	cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
 	disable-wp;
+	ti,fails-without-test-cd;
 	vmmc-supply = <&reg_sdhc1_vmmc>;
 	vqmmc-supply = <&reg_sdhc1_vqmmc>;
 	status = "disabled";
-- 
2.39.2