[PATCH 3/4] arm64: dts: add support for A4 based Amlogic BA400

[Xianwei Zhao via B4 Relay]

From: Xianwei Zhao <xianwei.zhao@xxxxxxxxxxx>

Amlogic A4 is an application processor designed for smart audio
and IoT applications.

Add basic support for the A4 based Amlogic BA400 board, which describes
the following components: CPU, GIC, IRQ, Timer and UART.
These are capable of booting up into the serial console.

Signed-off-by: Xianwei Zhao <xianwei.zhao@xxxxxxxxxxx>
---
 arch/arm64/boot/dts/amlogic/Makefile               |  1 +
 .../boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts   | 43 ++++++++++
 arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi        | 99 ++++++++++++++++++++++
 3 files changed, 143 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 1ab160bf928a..9a50ec11bb8d 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MESON) += amlogic-a4-a113l2-ba400.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-an400.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-khadas-vim4.dtb
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts b/arch/arm64/boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts
new file mode 100644
index 000000000000..60f9f23858c6
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-a4-a113l2-ba400.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "amlogic-a4.dtsi"
+
+/ {
+	model = "Amlogic A113L2 ba400 Development Board";
+	compatible = "amlogic,ba400","amlogic,a4";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart_b;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 52 MiB reserved for ARM Trusted Firmware */
+		secmon_reserved:linux,secmon {
+			compatible = "shared-dma-pool";
+			no-map;
+			alignment = <0x0 0x400000>;
+			reg = <0x0 0x05000000 0x0 0x3400000>;
+		};
+	};
+};
+
+&uart_b {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi
new file mode 100644
index 000000000000..7e8745010b52
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-a4.dtsi
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller@fff01000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xfff01000 0 0x1000>,
+			      <0x0 0xfff02000 0 0x2000>,
+			      <0x0 0xfff04000 0 0x2000>,
+			      <0x0 0xfff06000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		apb@fe000000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xfe000000 0x0 0x480000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+
+			uart_b: serial@7a000 {
+				compatible = "amlogic,meson-s4-uart",
+					     "amlogic,meson-ao-uart";
+				reg = <0x0 0x7a000 0x0 0x18>;
+				interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+		};
+	};
+};

-- 
2.37.1