Re: [RFC PATCH v3 4/5] input: add onkey driver for Marvell 88PM886 PMIC

From: Karel Balej
Date: Mon Mar 11 2024 - 06:25:56 EST


Krzysztof Kozlowski, 2024-03-10T21:35:36+01:00:
> On 10/03/2024 12:35, Karel Balej wrote:
> > Dmitry Torokhov, 2024-03-04T17:10:59-08:00:
> >> On Mon, Mar 04, 2024 at 09:28:45PM +0100, Karel Balej wrote:
> >>> Dmitry,
> >>>
> >>> Dmitry Torokhov, 2024-03-03T12:39:46-08:00:
> >>>> On Sun, Mar 03, 2024 at 11:04:25AM +0100, Karel Balej wrote:
> >>>>> From: Karel Balej <balejk@xxxxxxxxx>
> >>>>>
> >>>>> Marvell 88PM886 PMIC provides onkey among other things. Add client
> >>>>> driver to handle it. The driver currently only provides a basic support
> >>>>> omitting additional functions found in the vendor version, such as long
> >>>>> onkey and GPIO integration.
> >>>>>
> >>>>> Signed-off-by: Karel Balej <balejk@xxxxxxxxx>
> >>>>> ---
> >>>>>
> >>>>> Notes:
> >>>>> RFC v3:
> >>>>> - Drop wakeup-source.
> >>>>> RFC v2:
> >>>>> - Address Dmitry's feedback:
> >>>>> - Sort includes alphabetically.
> >>>>> - Drop onkey->irq.
> >>>>> - ret -> err in irq_handler and no initialization.
> >>>>> - Break long lines and other formatting.
> >>>>> - Do not clobber platform_get_irq error.
> >>>>> - Do not set device parent manually.
> >>>>> - Use input_set_capability.
> >>>>> - Use the wakeup-source DT property.
> >>>>> - Drop of_match_table.
> >>>>
> >>>> I only said that you should not be using of_match_ptr(), but you still
> >>>> need to have of_match_table set and have MODULE_DEVICE_TABLE() for the
> >>>> proper module loading support.
> >>>
> >>> I removed of_match_table because I no longer need compatible for this --
> >>> there are no device tree properties and the driver is being instantiated
> >>> by the MFD driver.
> >>>
> >>> Is the MODULE_DEVICE_TABLE() entry needed for the driver to probe when
> >>> compiled as module? If that is the case, given what I write above, am I
> >>> correct that MODULE_DEVICE_TABLE(platform,...) would be the right thing
> >>> to use here?
> >>
> >> Yes, if uevent generated for the device is "platform:<name>" then
> >> MODULE_DEVICE_TABLE(platform,...) will suffice. I am not sure how MFD
> >> sets it up (OF modalias or platform), but you should be able to check
> >> the format looking at the "uevent" attribute for your device in sysfs
> >> (/sys/devices/bus/platform/...).
> >
> > The uevent is indeed platform.
> >
> > But since there is only one device, perhaps having a device table is
> > superfluous and using `MODULE_ALIAS("platform:88pm886-onkey")` is more
> > fitting?
>
> Adding aliases for standard IDs and standard cases is almost never
> correct. If you need module alias, it means your ID table is wrong (or
> missing, which is usually wrong).
>
> >
> > Although I don't understand why this is even necessary when the driver
> > name is such and the module is registered using
> > `module_platform_driver`...
>
> ID table and MODULE_DEVICE_TABLE() are necessary for modprobe to work.

I think I understand the practical reasons. My point was that I would
expect the alias to be added automatically even in the case that the
device table is absent based solely on the driver name and the
registration method (*module*_*platform*_driver). Why is that not the
case? Obviously the driver name matching the mfd_cell name is sufficient
for the driver to probe when it is built in so the name does seem to
serve as some identification for the device just as a device table entry
would.

Furthermore, drivers/input/serio/ioc3kbd.c does not seem to have an ID
table either, nor a MODULE_ALIAS -- is that a mistake? If not, what
mechanism causes the driver to probe when compiled as a module? It seems
to me to effectively be the same setup as with my driver and that does
not load automatically (because of the missing alias).

> Just run `modinfo`.

Thank you very much,
K. B.