Re: [PATCH] arm: dts: ti: beagleplay: Fix Ethernet PHY RESET GPIOs

[Roger Quadros]

On 04/03/2024 06:24, Vignesh Raghavendra wrote:
> Hi Roger,
> 
> On 02/03/24 02:59, Roger Quadros wrote:
>>
>>
>> On 01/03/2024 22:58, Roger Quadros wrote:
>>>
>>>
>>> On 29/02/2024 18:25, Roger Quadros wrote:
>>>> The RESET GPIO pinmux should be part of MDIO bus node
>>>> so that they can be in the right state before the PHY
>>>> can be probed via MDIO bus scan.
>>>>
>>>> Add GPIO reset for the Gigabit Ethernet PHY. As per
>>>> RTL8211F datasheet, reset assert width is 10ms and
>>>> PHY registers can be access accessed after 50ms of
>>>> reset deassert.
>>>>
>>>> Signed-off-by: Roger Quadros <rogerq@xxxxxxxxxx>
>>>> ---
>>>>  arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts | 8 ++++++--
>>>>  1 file changed, 6 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
>>>> index a34e0df2ab86..77240cf3ae4d 100644
>>>> --- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
>>>> +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
>>>> @@ -292,6 +292,8 @@ mdio0_pins_default: mdio0-default-pins {
>>>>  		pinctrl-single,pins = <
>>>>  			AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
>>>>  			AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
>>>> +			AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25) GPMC0_AD0.GPIO0_15 */
>>>
>>> This should be PIN_OUTPUT.
>>> Will fix in next spin.
>>
>> Actually PIN_INPUT is correct else we won't be able to read the correct GPIO pin status
>> on gpio read.
>> I observe this issue on u-boot at least.
>>
>>>
>>>> +			AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
>>
>> This one needs to be fixed to PIN_INPUT.
> 
> While at it, please fix the $subject prefix:
> 
> arm64: dts: ti: beagleplay: ...

Right.

> 
> Do we need a Fixes: Tag too?

Sure, I'll add.

> 
>>
>>>>  		>;
>>>>  	};
>>>>  
>>>> @@ -383,7 +385,6 @@ AM62X_IOPAD(0x017c, PIN_INPUT, 1) /* (AD22) RGMII2_RX_CTL.RMII2_RX_ER */
>>>>  			AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
>>>>  			AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
>>>>  			AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
>>>> -			AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
>>>>  			AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
>>>>  			AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
>>>>  		>;
>>>> @@ -597,6 +598,9 @@ &cpsw3g_mdio {
>>>>  
>>>>  	cpsw3g_phy0: ethernet-phy@0 {
>>>>  		reg = <0>;
>>>> +		reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
>>>> +		reset-assert-us = <10000>;
>>>> +		reset-deassert-us = <50000>;
>>>>  	};
>>>>  
>>>>  	cpsw3g_phy1: ethernet-phy@1 {
>>>> @@ -615,7 +619,7 @@ &main_gpio0 {
>>>>  		"USR0", "USR1", "USR2", "USR3", "", "", "USR4",	/* 3-9 */
>>>>  		"EEPROM_WP",					/* 10 */
>>>>  		"CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2",	/* 11-12 */
>>>> -		"CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "",	/* 13-17 */
>>>> +		"CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "",	/* 13-17 */
>>>>  		"USR_BUTTON", "", "", "", "", "", "", "", "",	/* 18-26 */
>>>>  		"", "", "", "", "", "", "", "", "", "HDMI_INT",	/* 27-36 */
>>>>  		"", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
>>>>
>>>> ---
>>>> base-commit: bbef42084cc170cbfc035bf784f2ff055c939d7e
>>>> change-id: 20240229-b4-for-v6-9-am65-beagleplay-ethernet-reset-098f274fbf15
>>>>
>>>> Best regards,
>>>
>>
> 

-- 
cheers,
-roger