[PATCH] firmware: qcom_scm: disable clocks if qcom_scm_bw_enable() fails

[Gabor Juhos]

There are several functions which are calling qcom_scm_bw_enable()
then returns immediately if the call fails and leaves the clocks
enabled.

Change the code of these functions to disable clocks when the
qcom_scm_bw_enable() call fails. This also fixes a possible dma
buffer leak in the qcom_scm_pas_init_image() function.

Compile tested only due to lack of hardware with interconnect
support.

Cc: stable@xxxxxxxxxxxxxxx
Fixes: 65b7ebda5028 ("firmware: qcom_scm: Add bw voting support to the SCM interface")
Signed-off-by: Gabor Juhos <j4g8y7@xxxxxxxxx>
---
Based on v6.8-rc7.

Note: Removing the two empty lines from qcom_scm_pas_init_image()
and fomr qcom_scm_pas_shutdown() functions is intentional to make
those consistent with the other two functions.
---
 drivers/firmware/qcom/qcom_scm.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 520de9b5633ab..e8460626fb0c4 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -569,13 +569,14 @@ int qcom_scm_pas_init_image(u32 peripheral, const void *metadata, size_t size,
 
 	ret = qcom_scm_bw_enable();
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	desc.args[1] = mdata_phys;
 
 	ret = qcom_scm_call(__scm->dev, &desc, &res);
-
 	qcom_scm_bw_disable();
+
+disable_clk:
 	qcom_scm_clk_disable();
 
 out:
@@ -637,10 +638,12 @@ int qcom_scm_pas_mem_setup(u32 peripheral, phys_addr_t addr, phys_addr_t size)
 
 	ret = qcom_scm_bw_enable();
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	ret = qcom_scm_call(__scm->dev, &desc, &res);
 	qcom_scm_bw_disable();
+
+disable_clk:
 	qcom_scm_clk_disable();
 
 	return ret ? : res.result[0];
@@ -672,10 +675,12 @@ int qcom_scm_pas_auth_and_reset(u32 peripheral)
 
 	ret = qcom_scm_bw_enable();
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	ret = qcom_scm_call(__scm->dev, &desc, &res);
 	qcom_scm_bw_disable();
+
+disable_clk:
 	qcom_scm_clk_disable();
 
 	return ret ? : res.result[0];
@@ -706,11 +711,12 @@ int qcom_scm_pas_shutdown(u32 peripheral)
 
 	ret = qcom_scm_bw_enable();
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	ret = qcom_scm_call(__scm->dev, &desc, &res);
-
 	qcom_scm_bw_disable();
+
+disable_clk:
 	qcom_scm_clk_disable();
 
 	return ret ? : res.result[0];

---
base-commit: 90d35da658da8cff0d4ecbb5113f5fac9d00eb72
change-id: 20240304-qcom-scm-disable-clk-08e7ad853fa1

Best regards,
-- 
Gabor Juhos <j4g8y7@xxxxxxxxx>