Re: [PATCH] drivers: iio: pressure: Add SPI support for BMP38x and BMP390

[Angel Iglesias]

On Thu, 2024-02-15 at 17:43 +0100, Vasileios Amoiridis wrote:
> According to the datasheet of BMP38x and BMP390 devices, in SPI
> operation, the first byte that returns after a read operation is
> garbage and it needs to be dropped and return the rest of the
> bytes.

Hey good catch! It flew past me when I added this devices because I tested only
on i2c at the time.

Kind regards,
Angel

> Signed-off-by: Vasileios Amoiridis <vassilisamir@xxxxxxxxx>
> ---
>  drivers/iio/pressure/bmp280-spi.c | 47 ++++++++++++++++++++++++++++++-
>  drivers/iio/pressure/bmp280.h     |  2 ++
>  2 files changed, 48 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-
> spi.c
> index 433d6fac83c4..c4b4a5d67f94 100644
> --- a/drivers/iio/pressure/bmp280-spi.c
> +++ b/drivers/iio/pressure/bmp280-spi.c
> @@ -35,6 +35,32 @@ static int bmp280_regmap_spi_read(void *context, const void
> *reg,
>  	return spi_write_then_read(spi, reg, reg_size, val, val_size);
>  }
>  
> +static int bmp380_regmap_spi_read(void *context, const void *reg,
> +				  size_t reg_size, void *val, size_t
> val_size)
> +{
> +	struct spi_device *spi = to_spi_device(context);
> +	u8 ret[BMP380_SPI_MAX_REG_COUNT_READ + 1];
> +	ssize_t status;
> +	u8 buf;
> +
> +	memcpy(&buf, reg, reg_size);
> +	buf |= 0x80;
> +
> +	/*
> +	 * According to the BMP380, BMP388, BMP390 datasheets, for a basic
> +	 * read operation, after the write is done, 2 bytes are received and
> +	 * the first one has to be dropped. The 2nd one is the requested
> +	 * value.
> +	 */
> +	status = spi_write_then_read(spi, &buf, 1, ret, val_size + 1);
> +	if (status)
> +		return status;
> +
> +	memcpy(val, ret + 1, val_size);
> +
> +	return 0;
> +}
> +
>  static struct regmap_bus bmp280_regmap_bus = {
>  	.write = bmp280_regmap_spi_write,
>  	.read = bmp280_regmap_spi_read,
> @@ -42,10 +68,18 @@ static struct regmap_bus bmp280_regmap_bus = {
>  	.val_format_endian_default = REGMAP_ENDIAN_BIG,
>  };
>  
> +static struct regmap_bus bmp380_regmap_bus = {
> +	.write = bmp280_regmap_spi_write,
> +	.read = bmp380_regmap_spi_read,
> +	.reg_format_endian_default = REGMAP_ENDIAN_BIG,
> +	.val_format_endian_default = REGMAP_ENDIAN_BIG,
> +};
> +
>  static int bmp280_spi_probe(struct spi_device *spi)
>  {
>  	const struct spi_device_id *id = spi_get_device_id(spi);
>  	const struct bmp280_chip_info *chip_info;
> +	struct regmap_bus *bmp_regmap_bus;
>  	struct regmap *regmap;
>  	int ret;
>  
> @@ -58,8 +92,19 @@ static int bmp280_spi_probe(struct spi_device *spi)
>  
>  	chip_info = spi_get_device_match_data(spi);
>  
> +	switch (chip_info->chip_id[0]) {
> +	case BMP380_CHIP_ID:
> +	case BMP390_CHIP_ID:
> +		bmp_regmap_bus = &bmp380_regmap_bus;
> +		break;
> +	default:
> +		bmp_regmap_bus = &bmp280_regmap_bus;
> +		break;
> +	}
> +
> +
>  	regmap = devm_regmap_init(&spi->dev,
> -				  &bmp280_regmap_bus,
> +				  bmp_regmap_bus,
>  				  &spi->dev,
>  				  chip_info->regmap_config);
>  	if (IS_ERR(regmap)) {
> diff --git a/drivers/iio/pressure/bmp280.h b/drivers/iio/pressure/bmp280.h
> index 4012387d7956..ca482b7e4295 100644
> --- a/drivers/iio/pressure/bmp280.h
> +++ b/drivers/iio/pressure/bmp280.h
> @@ -191,6 +191,8 @@
>  #define BMP380_TEMP_SKIPPED		0x800000
>  #define BMP380_PRESS_SKIPPED		0x800000
>  
> +#define BMP380_SPI_MAX_REG_COUNT_READ   3
> +
>  /* BMP280 specific registers */
>  #define BMP280_REG_HUMIDITY_LSB		0xFE
>  #define BMP280_REG_HUMIDITY_MSB		0xFD