[PATCH] dt-bindings: dma: convert atmel-dma.txt to YAML

[Durai Manickam KR]

Added a description, required properties and appropriate compatibles
for all the SoCs that are supported by microchip.

Signed-off-by: Durai Manickam KR <durai.manickamkr@xxxxxxxxxxxxx>
---
 .../devicetree/bindings/dma/atmel-dma.txt          | 42 -------------
 .../bindings/dma/microchip,at91-dma.yaml           | 71 ++++++++++++++++++++++
 2 files changed, 71 insertions(+), 42 deletions(-)

diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt
deleted file mode 100644
index f69bcf5a6343..000000000000
--- a/Documentation/devicetree/bindings/dma/atmel-dma.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-* Atmel Direct Memory Access Controller (DMA)
-
-Required properties:
-- compatible: Should be "atmel,<chip>-dma".
-- reg: Should contain DMA registers location and length.
-- interrupts: Should contain DMA interrupt.
-- #dma-cells: Must be <2>, used to represent the number of integer cells in
-the dmas property of client devices.
-
-Example:
-
-dma0: dma@ffffec00 {
-	compatible = "atmel,at91sam9g45-dma";
-	reg = <0xffffec00 0x200>;
-	interrupts = <21>;
-	#dma-cells = <2>;
-};
-
-DMA clients connected to the Atmel DMA controller must use the format
-described in the dma.txt file, using a three-cell specifier for each channel:
-a phandle plus two integer cells.
-The three cells in order are:
-
-1. A phandle pointing to the DMA controller.
-2. The memory interface (16 most significant bits), the peripheral interface
-(16 less significant bits).
-3. Parameters for the at91 DMA configuration register which are device
-dependent:
-  - bit 7-0: peripheral identifier for the hardware handshaking interface. The
-  identifier can be different for tx and rx.
-  - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 2 for ASAP.
-
-Example:
-
-i2c0@i2c@f8010000 {
-	compatible = "atmel,at91sam9x5-i2c";
-	reg = <0xf8010000 0x100>;
-	interrupts = <9 4 6>;
-	dmas = <&dma0 1 7>,
-	       <&dma0 1 8>;
-	dma-names = "tx", "rx";
-};
diff --git a/Documentation/devicetree/bindings/dma/microchip,at91-dma.yaml b/Documentation/devicetree/bindings/dma/microchip,at91-dma.yaml
new file mode 100644
index 000000000000..a0a582902e4d
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/microchip,at91-dma.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/microchip,at91-dma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Atmel Direct Memory Access Controller (DMA)
+
+maintainers:
+  - Ludovic Desroches <ludovic.desroches@xxxxxxxxxxxxx>
+  - Tudor Ambarus <tudor.ambarus@xxxxxxxxxx>
+
+description: |
+  The Atmel Direct Memory Access Controller (DMAC) transfers data from a source
+  peripheral to a destination peripheral over one or more AMBA buses. One channel
+  is required for each source/destination pair. In the most basic configuration,
+  the DMAC has one master interface and one channel. The master interface reads
+  the data from a source and writes it to a destination. Two AMBA transfers are
+  required for each DMAC data transfer. This is also known as a dual-access transfer.
+  The DMAC is programmed via the APB interface.
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - atmel,at91sam9g45-dma
+          - atmel,at91sam9rl-dma
+  reg:
+    description: Should contain DMA registers location and length.
+    maxItems: 1
+
+  interrupts:
+    description: Should contain the DMA interrupts associated to the DMA channels.
+    maxItems: 1
+
+  "#dma-cells":
+    description:
+      Must be <2>, used to represent the number of integer cells in the dmas
+      property of client devices.
+    const: 2
+
+  clocks:
+    description: Should contain a clock specifier for each entry in clock-names.
+    maxItems: 1
+
+  clock-names:
+    description: Should contain the clock of the DMA controller.
+    const: dma_clk
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#dma-cells"
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    dma0: dma-controller@ffffec00 {
+            compatible = "atmel,at91sam9g45-dma";
+            reg = <0xffffec00 0x200>;
+            interrupts = <21>;
+            #dma-cells = <2>;
+            clocks = <&pmc 2 20>;
+            clock-names = "dma_clk";
+    };
+
+...

---
base-commit: 7e90b5c295ec1e47c8ad865429f046970c549a66
change-id: 20240214-dmac-5f48fd7f3b9d

Best regards,
-- 
Durai Manickam KR <durai.manickamkr@xxxxxxxxxxxxx>