Re: [PATCH v4 2/3] docs: iio: add documentation for device buffers
From: David Lechner
Date: Tue Feb 13 2024 - 19:00:34 EST
On Tue, Feb 13, 2024 at 2:19 AM Ramona Gradinariu
<ramona.gradinariu@xxxxxxxxxx> wrote:
>
> Add documentation for IIO device buffers describing buffer
> attributes and how data is structured in buffers using
> scan elements.
Really nice to see this being added to the docs.
>
> Signed-off-by: Ramona Gradinariu <ramona.gradinariu@xxxxxxxxxx>
> ---
> changes in v4:
> - documented multiple buffer support
> - reworked scan elements section
> - added reference to ABI docs
> Documentation/iio/iio_devbuf.rst | 125 +++++++++++++++++++++++++++++++
> Documentation/iio/index.rst | 1 +
> 2 files changed, 126 insertions(+)
> create mode 100644 Documentation/iio/iio_devbuf.rst
>
> diff --git a/Documentation/iio/iio_devbuf.rst b/Documentation/iio/iio_devbuf.rst
> new file mode 100644
> index 000000000000..e99143efb4d7
> --- /dev/null
> +++ b/Documentation/iio/iio_devbuf.rst
> @@ -0,0 +1,125 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +=============================
> +Industrial IIO device buffers
> +=============================
> +
> +1. Overview
> +===========
> +
> +The Industrial I/O core offers a way for continuous data capture based on a
> +trigger source. Multiple data channels can be read at once from
> +/dev/iio:deviceX character device node, thus reducing the CPU load.
It could be nice to use inline code format style (double-backtick,
e.g. ``/dev/iio:deviceX``) on paths like this throughout the document.
> +
> +Devices with buffer support feature an additional sub-folder in the
> +/sys/bus/iio/devices/deviceX/ folder hierarchy, called bufferY, where Y defaults
Should this be `iio:deviceX` instead of `deviceX` to match the sysfs docs?
> +to 0, for devices with a single buffer.
Is /sys/bus/iio/devices/deviceX/buffer (without the Y) for backwards
compatibility?
> +
> +2. Buffer attributes
> +====================
> +
> +An IIO buffer has an associated attributes directory under
> +/sys/bus/iio/iio:deviceX/bufferY/. The attributes are described below.
> +
> +Length
> +------
Could be nice to give the actual attribute name ``length`` here to
avoid possible case-sensitivity confusion with the section header.
Same applies to other attributes.
> +
> +Read / Write attribute which states the total number of data samples (capacity)
> +that can be stored by the buffer.
> +
> +Enable
> +------
> +
> +Read / Write attribute which starts / stops the buffer capture. This file should
> +be written last, after length and selection of scan elements.
Could be useful here to mention that writing a non-zero value here to
enable the buffer may result in an error, such as EINVAL, e.g. if an
invalid configuration was selected, like choosing a combination of
scan elements that don't match one of the valid scan masks.
> +
> +Watermark
> +---------
> +
> +Read / Write positive integer attribute specifying the maximum number of scan
> +elements to wait for.
> +
> +Poll will block until the watermark is reached.
> +
> +Blocking read will wait until the minimum between the requested read amount or
> +the low water mark is available.
> +
> +Non-blocking read will retrieve the available samples from the buffer even if
> +there are less samples then watermark level. This allows the application to
> +block on poll with a timeout and read the available samples after the timeout
> +expires and thus have a maximum delay guarantee.
> +
> +Data available
> +--------------
> +
> +Read-only attribute indicating the bytes of data available in the buffer In the
> +case of an output buffer, this indicates the amount of empty space available to
> +write data to. In the case of an input buffer, this indicates the amount of data
> +available for reading.
> +
> +Scan elements
> +-------------
> +
> +The meta information associated with a channel reading placed in a buffer is
Maybe say "data" instead of "reading" here since it could be writing
instead for DACs.
> +called a scan element. The scan elements are configurable per buffer, thus they
> +are exposed to userspace applications via the /sys/bus/iio/iio:deviceX/bufferY/
Giving the directory again seems redundant here.
> +directory. The scan elements attributes are presented below.
> +
> +**_en**
> +
> +Read/ Write attribute used for enabling a channel. If and only if its value
> +is non zero, then a triggered capture will contain data samples for this
> +channel.
> +
> +**_index**
> +
> +Read-only positive integer attribute specifying the position of the channel in
Isn't 0 a valid scan index? So non-negative? Or unsigned?
> +the buffer. Note these are not dependent on what is enabled and may not be
> +contiguous. Thus for user-space to establish the full layout these must be used
> +in conjunction with all _en attributes to establish which channels are present,
> +and the relevant _type attributes to establish the data storage format.
> +
It would also be nice to get an example on the binary layout for
something that has multiple channels enabled. In particular with the
data alignment, e.g. when you have a 16-bit word followed by a 64-bit
word.
> +**_type**
> +
> +Read-only attribute containing the description of the scan element data storage
> +within the buffer and hence the form in which it is read from user space Format
> +is [be|le]:[s|u]bits/storagebits[Xrepeat][>>shift], where:
> +
> +- **be** or **le** specifies big or little endian.
> +- **s** or **u**, specifies if signed (2's complement) or unsigned.
> +- **bits**, is the number of valid data bits.
> +- **storagebits**, is the number of bits (after padding) that it occupies in the
> + buffer.
> +- **repeat**, specifies the number of bits/storagebits repetitions. When the
> + repeat element is 0 or 1, then the repeat value is omitted.
> +- **shift**, if specified, is the shift that needs to be applied prior to
> + masking out unused bits.
> +
> +For example, a driver for a 3-axis accelerometer with 12 bit resolution where
> +data is stored in two 8-bits registers as follows:
> +
> +.. code-block:: bash
Doesn't look like this should use "bash" styling.
> +
> + 7 6 5 4 3 2 1 0
> + +---+---+---+---+---+---+---+---+
> + |D3 |D2 |D1 |D0 | X | X | X | X | (LOW byte, address 0x06)
> + +---+---+---+---+---+---+---+---+
> +
> + 7 6 5 4 3 2 1 0
> + +---+---+---+---+---+---+---+---+
> + |D11|D10|D9 |D8 |D7 |D6 |D5 |D4 | (HIGH byte, address 0x07)
> + +---+---+---+---+---+---+---+---+
> +
> +will have the following scan element type for each axis:
> +
> +.. code-block:: bash
> +
> + $ cat /sys/bus/iio/devices/iio:device0/buffer0/in_accel_y_type
> + le:s12/16>>4
> +
> +A user space application will interpret data samples read from the buffer as two
> +byte little endian signed data, that needs a 4 bits right shift before masking
> +out the 12 valid bits of data.
Is it always assumed that scan data is `raw` and needs to be
multiplied by `scale` for that channel to convert it to SI (or IIO
standard) units?
> +
> +Please see Documentation/ABI/testing/sysfs-bus-iio for a complete description of
> +the attributes.
Is it also worth mentioning
``Documentation/ABI/testing/sysfs-bus-iio-dma-buffer`` here?
> diff --git a/Documentation/iio/index.rst b/Documentation/iio/index.rst
> index db341b45397f..206a0aff5ca1 100644
> --- a/Documentation/iio/index.rst
> +++ b/Documentation/iio/index.rst
> @@ -8,6 +8,7 @@ Industrial I/O
> :maxdepth: 1
>
> iio_configfs
> + iio_devbuf
>
> Industrial I/O Kernel Drivers
> =============================
> --
> 2.34.1
>
>