Re: [PATCH netnext 8/8] net: dsa: mt7530: simplify link operations and force link down on all ports

[Daniel Golle]

On Thu, Feb 08, 2024 at 08:51:36AM +0300, Arınç ÜNAL via B4 Relay wrote:
> From: Arınç ÜNAL <arinc.unal@xxxxxxxxxx>
> 
> Currently, the link operations for switch MACs are scattered across
> port_enable, port_disable, phylink_mac_config, phylink_mac_link_up, and
> phylink_mac_link_down.
> 
> port_enable and port_disable clears the link settings. Move that to
> mt7530_setup() and mt7531_setup_common() which set up the switches. This
> way, the link settings are cleared on all ports at setup, and then only
> once with phylink_mac_link_down() when a link goes down.
> 
> Enable force mode at setup to apply the force part of the link settings.
> This ensures that only active ports will have their link up.
> 
> Now that the bit for setting the port on force mode is done on
> mt7530_setup() and mt7531_setup_common(), get rid of PMCR_FORCE_MODE_ID()
> which helped determine which bit to use for the switch model.
> 
> The "MT7621 Giga Switch Programming Guide v0.3", "MT7531 Reference Manual
> for Development Board v1.0", and "MT7988A Wi-Fi 7 Generation Router
> Platform: Datasheet (Open Version) v0.1" documents show that these bits are
> enabled at reset:
> 
> PMCR_IFG_XMIT(1) (not part of PMCR_LINK_SETTINGS_MASK)
> PMCR_MAC_MODE (not part of PMCR_LINK_SETTINGS_MASK)
> PMCR_TX_EN
> PMCR_RX_EN
> PMCR_BACKOFF_EN (not part of PMCR_LINK_SETTINGS_MASK)
> PMCR_BACKPR_EN (not part of PMCR_LINK_SETTINGS_MASK)
> PMCR_TX_FC_EN
> PMCR_RX_FC_EN
> 
> These bits also don't exist on the MT7530_PMCR_P(6) register of the switch
> on the MT7988 SoC:
> 
> PMCR_IFG_XMIT()
> PMCR_MAC_MODE
> PMCR_BACKOFF_EN
> PMCR_BACKPR_EN
> 
> Remove the setting of the bits not part of PMCR_LINK_SETTINGS_MASK on
> phylink_mac_config as they're already set.
> 
> Suggested-by: Vladimir Oltean <olteanv@xxxxxxxxx>
> Signed-off-by: Arınç ÜNAL <arinc.unal@xxxxxxxxxx>
> ---
>  drivers/net/dsa/mt7530.c | 26 +++++++++++++-------------
>  drivers/net/dsa/mt7530.h |  2 --
>  2 files changed, 13 insertions(+), 15 deletions(-)
> 
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index 5c8ad41ce8cd..f67db577d1c0 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -1018,7 +1018,6 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
>  	priv->ports[port].enable = true;
>  	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
>  		   priv->ports[port].pm);
> -	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
>  
>  	mutex_unlock(&priv->reg_mutex);
>  
> @@ -1038,7 +1037,6 @@ mt7530_port_disable(struct dsa_switch *ds, int port)
>  	priv->ports[port].enable = false;
>  	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
>  		   PCR_MATRIX_CLR);
> -	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
>  
>  	mutex_unlock(&priv->reg_mutex);
>  }
> @@ -2257,6 +2255,12 @@ mt7530_setup(struct dsa_switch *ds)
>  	mt7530_mib_reset(ds);
>  
>  	for (i = 0; i < MT7530_NUM_PORTS; i++) {
> +		/* Clear link settings and enable force mode to force link down
> +		 * on all ports until they're enabled later.
> +		 */
> +		mt7530_clear(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK);
> +		mt7530_set(priv, MT7530_PMCR_P(i), PMCR_FORCE_MODE);

Any reason to not combine the two lines above into a single call:

mt7530_rmw(priv, MT7530_PMCR_P(i),
	   PMCR_LINK_SETTINGS_MASK | PMCR_FORCE_MODE,
	   PMCR_FORCE_MODE);

> +
>  		/* Disable forwarding by default on all ports */
>  		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
>  			   PCR_MATRIX_CLR);
> @@ -2359,6 +2363,12 @@ mt7531_setup_common(struct dsa_switch *ds)
>  		     UNU_FFP_MASK);
>  
>  	for (i = 0; i < MT7530_NUM_PORTS; i++) {
> +		/* Clear link settings and enable force mode to force link down
> +		 * on all ports until they're enabled later.
> +		 */
> +		mt7530_clear(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK);
> +		mt7530_set(priv, MT7530_PMCR_P(i), MT7531_FORCE_MODE);
> +

Same here obviously.

>  		/* Disable forwarding by default on all ports */
>  		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
>  			   PCR_MATRIX_CLR);
> @@ -2657,23 +2667,13 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
>  			  const struct phylink_link_state *state)
>  {
>  	struct mt7530_priv *priv = ds->priv;
> -	u32 mcr_cur, mcr_new;
>  
>  	if ((port == 5 || port == 6) && priv->info->mac_port_config)
>  		priv->info->mac_port_config(ds, port, mode, state->interface);
>  
> -	mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
> -	mcr_new = mcr_cur;
> -	mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
> -	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
> -		   PMCR_BACKPR_EN | PMCR_FORCE_MODE_ID(priv->id);
> -
>  	/* Are we connected to external phy */
>  	if (port == 5 && dsa_is_user_port(ds, 5))
> -		mcr_new |= PMCR_EXT_PHY;
> -
> -	if (mcr_new != mcr_cur)
> -		mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
> +		mt7530_set(priv, MT7530_PMCR_P(port), PMCR_EXT_PHY);
>  }
>  
>  static void mt753x_phylink_mac_link_down(struct dsa_switch *ds, int port,
> diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
> index 8a8144868eaa..a71166e0a7fc 100644
> --- a/drivers/net/dsa/mt7530.h
> +++ b/drivers/net/dsa/mt7530.h
> @@ -304,8 +304,6 @@ enum mt7530_vlan_port_acc_frm {
>  					 MT7531_FORCE_DPX | \
>  					 MT7531_FORCE_RX_FC | \
>  					 MT7531_FORCE_TX_FC)
> -#define  PMCR_FORCE_MODE_ID(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
> -					 MT7531_FORCE_MODE : PMCR_FORCE_MODE)
>  #define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
>  					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
>  					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
> 
> -- 
> 2.40.1
>