Re: [PATCH v12 5/5] iommu/vt-d: improve ITE fault handling if target device isn't present
From: Ethan Zhao
Date: Tue Jan 30 2024 - 00:12:57 EST
On 1/29/2024 5:21 PM, Yi Liu wrote:
On 2024/1/29 17:06, Tian, Kevin wrote:
From: Ethan Zhao <haifeng.zhao@xxxxxxxxxxxxxxx>
Sent: Monday, January 29, 2024 11:49 AM
Because surprise removal could happen anytime, e.g. user could
request safe
removal to EP(endpoint device) via sysfs and brings its link down to do
surprise removal cocurrently. such aggressive cases would cause ATS
invalidation request issued to non-existence target device, then deadly
loop to retry that request after ITE fault triggered in interrupt
context.
this patch aims to optimize the ITE handling by checking the target
device
presence state to avoid retrying the timeout request blindly, thus
avoid
hard lockup or system hang.
Signed-off-by: Ethan Zhao <haifeng.zhao@xxxxxxxxxxxxxxx>
---
drivers/iommu/intel/dmar.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/iommu/intel/dmar.c b/drivers/iommu/intel/dmar.c
index 814134e9aa5a..2e214b43725c 100644
--- a/drivers/iommu/intel/dmar.c
+++ b/drivers/iommu/intel/dmar.c
@@ -1272,6 +1272,7 @@ static int qi_check_fault(struct intel_iommu
*iommu, int index, int wait_index,
{
u32 fault;
int head, tail;
+ u64 iqe_err, ite_sid;
struct q_inval *qi = iommu->qi;
int shift = qi_shift(iommu);
@@ -1316,6 +1317,13 @@ static int qi_check_fault(struct intel_iommu
*iommu, int index, int wait_index,
tail = readl(iommu->reg + DMAR_IQT_REG);
tail = ((tail >> shift) - 1 + QI_LENGTH) % QI_LENGTH;
+ /*
+ * SID field is valid only when the ITE field is Set in
FSTS_REG
+ * see Intel VT-d spec r4.1, section 11.4.9.9
+ */
+ iqe_err = dmar_readq(iommu->reg + DMAR_IQER_REG);
+ ite_sid = DMAR_IQER_REG_ITESID(iqe_err);
+
writel(DMA_FSTS_ITE, iommu->reg + DMAR_FSTS_REG);
pr_info("Invalidation Time-out Error (ITE) cleared\n");
@@ -1325,6 +1333,16 @@ static int qi_check_fault(struct intel_iommu
*iommu, int index, int wait_index,
head = (head - 2 + QI_LENGTH) % QI_LENGTH;
} while (head != tail);
+ /*
+ * If got ITE, we need to check if the sid of ITE is the
same as
+ * current ATS invalidation target device, if yes, don't
try this
+ * request anymore if the target device isn't present.
+ * 0 value of ite_sid means old VT-d device, no ite_sid value.
+ */
+ if (pdev && ite_sid && !pci_device_is_present(pdev) &&
+ ite_sid == pci_dev_id(pci_physfn(pdev)))
+ return -ETIMEDOUT;
+
since the hardware already reports source id leading to timeout,
can't we
just find the pci_dev according to reported ite_sid? this is a slow
path (either
due to device in bad state or removed) hence it's not necessary to
add more
intelligence to pass the pci_dev in, leading to only a partial fix
can be backported.
It's also more future-proof, say if one day the driver allows
batching invalidation
requests for multiple devices then no need to pass in a list of devices.
Then it's easier to backport a full fix.
May consider pci_get_domain_bus_and_slot() or
pci_find_bus()/pci_get_slot(). But I doubt if the pci_dev is still
tracked
in the bus or a kind of dev list in the device hot removal case. So Ethan
may need to check.
Perhaps it is too late to call pci_find_bus() or
pci_get_domain_bus_and_slot() to get the
device instance from this notifier registered as BUS_NOTIFY_REMOVED_DEVICE
action. if the device is still there in bus list, *must* be a bug of
device subsystem as
*removed* device.
but if we call iommu_release_device() in iommu_bus_notifier() for
BUS_NOTIFY_DEL_DEVICE
action, there should be opportuniy to get the device instance, but that
change need
more evaluation about side effect.
furthermore, iommu never cross domain number per context table
defination in VT-d
spec, not mean, domain number in a system never will be !0, per my
understanding.
Thanks,
Ethan
Regards,
Yi Liu