Re: [PATCH V14 07/21] mmc: core: Support UHS-II card control and access
From: Victor Shih
Date: Sat Jan 27 2024 - 03:29:05 EST
On Tue, Jan 23, 2024 at 2:28 PM Victor Shih <victorshihgli@xxxxxxxxx> wrote:
>
> From: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
>
> Embed UHS-II access/control functionality into the MMC request
> processing flow.
>
> Signed-off-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> Signed-off-by: Jason Lai <jason.lai@xxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
> ---
>
> Updates in V13:
> - Separate __mmc_go_idle() into one patch for re-factorring the code.
> - Move mmc_decode_scr declaration to sd.h.
> - Ues uhs2_sd_tran to stead MMC_UHS2_SD_TRAN.
> - Drop unnecessary comment.
>
> Updates in V12:
> - Use mmc_op_multi() to check DCMD which supports multi read/write
> in mmc_uhs2_prepare_cmd().
>
> Updates in V10:
> - Move some definitions of PatchV9[02/23] to PatchV10[06/23].
> - Move some definitions of PatchV9[05/23] to PatchV10[06/23].
> - Drop do_multi in the mmc_blk_rw_rq_prep().
> - Use tmode_half_duplex to instead of uhs2_tmode0_flag.
> - Move entire control of the tmode into mmc_uhs2_prepare_cmd().
>
> Updates in V8:
> - Add MMC_UHS2_SUPPORT to be cleared in sd_uhs2_detect().
> - Modify return value in sd_uhs2_attach().
>
> Updates in V7:
> - Add mmc_uhs2_card_prepare_cmd helper function in sd_ops.h.
> - Drop uhs2_state in favor of ios->timing.
> - Remove unnecessary functions.
>
> ---
>
> drivers/mmc/core/core.c | 10 +-
> drivers/mmc/core/sd.c | 10 +-
> drivers/mmc/core/sd.h | 5 +
> drivers/mmc/core/sd_ops.c | 9 +
> drivers/mmc/core/sd_ops.h | 17 +
> drivers/mmc/core/sd_uhs2.c | 1115 ++++++++++++++++++++++++++++++++++--
> include/linux/mmc/core.h | 13 +
> include/linux/mmc/host.h | 15 +
> 8 files changed, 1155 insertions(+), 39 deletions(-)
>
> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
> index 2edf31492a5d..be77cebe1fb8 100644
> --- a/drivers/mmc/core/core.c
> +++ b/drivers/mmc/core/core.c
> @@ -334,6 +334,8 @@ static int mmc_mrq_prep(struct mmc_host *host, struct mmc_request *mrq)
>
> int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
> {
> + struct uhs2_command uhs2_cmd;
> + __be32 payload[4]; /* for maximum size */
> int err;
>
> init_completion(&mrq->cmd_completion);
> @@ -351,6 +353,8 @@ int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
> if (err)
> return err;
>
> + mmc_uhs2_card_prepare_cmd(host, mrq, uhs2_cmd, payload);
> +
> led_trigger_event(host->led, LED_FULL);
> __mmc_start_request(host, mrq);
>
Hi, Adrian
I referenced your comments of the V9:
Refer:
https://patchwork.kernel.org/project/linux-mmc/patch/20230721101349.12387-7-victorshihgli@xxxxxxxxx/
My understanding is as follows, please correct me if there are any mistakes.
There is already "struct uhs2_command *uhs2_cmd" in struct mmc_command.
If I also put "__be32 payload[4]" in struct mmc_command.
The code will become:
mmc_uhs2_card_prepare_cmd(host, mrq, *mrq->cmd->uhs2_cmd, mrq->cmd->payload);
But a null pointer problem occurs when sending commands like COM0(mmc_go_idle).
In this case I just can only plan for the time being as follows:
if (mrq->cmd->uhs2_cmd)
mmc_uhs2_card_prepare_cmd(host, mrq, *mrq->cmd->uhs2_cmd,
mrq->cmd->payload);
else
mmc_uhs2_card_prepare_cmd(host, mrq, uhs2_cmd, payload);
Would you give me any other advice?
Thanks, Victor Shih
> @@ -430,6 +434,8 @@ EXPORT_SYMBOL(mmc_wait_for_req_done);
> */
> int mmc_cqe_start_req(struct mmc_host *host, struct mmc_request *mrq)
> {
> + struct uhs2_command uhs2_cmd;
> + __be32 payload[4]; /* for maximum size */
> int err;
>
> /*
> @@ -450,6 +456,8 @@ int mmc_cqe_start_req(struct mmc_host *host, struct mmc_request *mrq)
> if (err)
> goto out_err;
>
> + mmc_uhs2_card_prepare_cmd(host, mrq, uhs2_cmd, payload);
> +
> err = host->cqe_ops->cqe_request(host, mrq);
> if (err)
> goto out_err;
> @@ -1132,7 +1140,7 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
> return 0;
> }
>
> - if (host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) {
> + if (!mmc_card_uhs2(host) && host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) {
> bit = ffs(ocr) - 1;
> ocr &= 3 << bit;
> mmc_power_cycle(host, ocr);
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index c3e554344c99..67fded1b2be0 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -207,7 +207,7 @@ static int mmc_decode_csd(struct mmc_card *card)
> /*
> * Given a 64-bit response, decode to our card SCR structure.
> */
> -static int mmc_decode_scr(struct mmc_card *card)
> +int mmc_decode_scr(struct mmc_card *card)
> {
> struct sd_scr *scr = &card->scr;
> unsigned int scr_struct;
> @@ -904,7 +904,7 @@ int mmc_sd_get_csd(struct mmc_card *card)
> return 0;
> }
>
> -static int mmc_sd_get_ro(struct mmc_host *host)
> +int mmc_sd_get_ro(struct mmc_host *host)
> {
> int ro;
>
> @@ -1630,7 +1630,7 @@ static void mmc_sd_detect(struct mmc_host *host)
> }
> }
>
> -static int sd_can_poweroff_notify(struct mmc_card *card)
> +int sd_can_poweroff_notify(struct mmc_card *card)
> {
> return card->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY;
> }
> @@ -1658,7 +1658,7 @@ static int sd_busy_poweroff_notify_cb(void *cb_data, bool *busy)
> return 0;
> }
>
> -static int sd_poweroff_notify(struct mmc_card *card)
> +int sd_poweroff_notify(struct mmc_card *card)
> {
> struct sd_busy_data cb_data;
> u8 *reg_buf;
> @@ -1706,7 +1706,7 @@ static int _mmc_sd_suspend(struct mmc_host *host)
> if (mmc_card_suspended(card))
> goto out;
>
> - if (sd_can_poweroff_notify(card))
> + if (mmc_sd_can_poweroff_notify(card))
> err = sd_poweroff_notify(card);
> else if (!mmc_host_is_spi(host))
> err = mmc_deselect_cards(host);
> diff --git a/drivers/mmc/core/sd.h b/drivers/mmc/core/sd.h
> index 1af5a038bae9..fbfaa3b00630 100644
> --- a/drivers/mmc/core/sd.h
> +++ b/drivers/mmc/core/sd.h
> @@ -11,10 +11,15 @@ struct mmc_card;
>
> int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr);
> int mmc_sd_get_csd(struct mmc_card *card);
> +int mmc_decode_scr(struct mmc_card *card);
> +int mmc_sd_get_ro(struct mmc_host *host);
> void mmc_decode_cid(struct mmc_card *card);
> int mmc_sd_setup_card(struct mmc_host *host, struct mmc_card *card,
> bool reinit);
> unsigned mmc_sd_get_max_clock(struct mmc_card *card);
> int mmc_sd_switch_hs(struct mmc_card *card);
>
> +int sd_can_poweroff_notify(struct mmc_card *card);
> +int sd_poweroff_notify(struct mmc_card *card);
> +
> #endif
> diff --git a/drivers/mmc/core/sd_ops.c b/drivers/mmc/core/sd_ops.c
> index a59cd592f06e..f22c7041632c 100644
> --- a/drivers/mmc/core/sd_ops.c
> +++ b/drivers/mmc/core/sd_ops.c
> @@ -27,6 +27,15 @@ int mmc_app_cmd(struct mmc_host *host, struct mmc_card *card)
> if (WARN_ON(card && card->host != host))
> return -EINVAL;
>
> + /*
> + * UHS2 packet has APP bit so only set APP_CMD flag here.
> + * Will set the APP bit when assembling UHS2 packet.
> + */
> + if (host->uhs2_sd_tran) {
> + host->uhs2_app_cmd = true;
> + return 0;
> + }
> +
> cmd.opcode = MMC_APP_CMD;
>
> if (card) {
> diff --git a/drivers/mmc/core/sd_ops.h b/drivers/mmc/core/sd_ops.h
> index 7667fc223b74..d3a3465c7669 100644
> --- a/drivers/mmc/core/sd_ops.h
> +++ b/drivers/mmc/core/sd_ops.h
> @@ -11,6 +11,7 @@
> #include <linux/types.h>
>
> struct mmc_card;
> +struct mmc_command;
> struct mmc_host;
>
> int mmc_app_set_bus_width(struct mmc_card *card, int width);
> @@ -21,6 +22,22 @@ int mmc_send_relative_addr(struct mmc_host *host, unsigned int *rca);
> int mmc_app_send_scr(struct mmc_card *card);
> int mmc_app_sd_status(struct mmc_card *card, void *ssr);
> int mmc_app_cmd(struct mmc_host *host, struct mmc_card *card);
> +void mmc_uhs2_prepare_cmd(struct mmc_host *host, struct mmc_request *mrq);
> +
> +static inline void mmc_uhs2_card_prepare_cmd(struct mmc_host *host, struct mmc_request *mrq,
> + struct uhs2_command uhs2_cmd, __be32 payload[4])
> +{
> + if (host->uhs2_sd_tran) {
> + uhs2_cmd.payload = payload;
> + mrq->cmd->uhs2_cmd = &uhs2_cmd;
> + mmc_uhs2_prepare_cmd(host, mrq);
> + }
> +}
> +
> +static inline int mmc_sd_can_poweroff_notify(struct mmc_card *card)
> +{
> + return card->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY;
> +}
>
> #endif
>
> diff --git a/drivers/mmc/core/sd_uhs2.c b/drivers/mmc/core/sd_uhs2.c
> index beb2541338ff..c46729d85644 100644
> --- a/drivers/mmc/core/sd_uhs2.c
> +++ b/drivers/mmc/core/sd_uhs2.c
> @@ -1,23 +1,51 @@
> // SPDX-License-Identifier: GPL-2.0-only
> /*
> * Copyright (C) 2021 Linaro Ltd
> - *
> * Author: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> *
> + * Copyright (C) 2014 Intel Corp, All Rights Reserved.
> + * Author: Yi Sun <yi.y.sun@xxxxxxxxx>
> + *
> + * Copyright (C) 2020 Genesys Logic, Inc.
> + * Authors: Ben Chuang <ben.chuang@xxxxxxxxxxxxxxxxxxx>
> + *
> + * Copyright (C) 2020 Linaro Limited
> + * Author: AKASHI Takahiro <takahiro.akashi@xxxxxxxxxx>
> + *
> + * Copyright (C) 2022 Genesys Logic, Inc.
> + * Authors: Jason Lai <jason.lai@xxxxxxxxxxxxxxxxxxx>
> + *
> + * Copyright (C) 2023 Genesys Logic, Inc.
> + * Authors: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
> + *
> * Support for SD UHS-II cards
> */
> #include <linux/err.h>
> +#include <linux/pm_runtime.h>
>
> #include <linux/mmc/host.h>
> #include <linux/mmc/card.h>
> +#include <linux/mmc/mmc.h>
> +#include <linux/mmc/sd.h>
> +#include <linux/mmc/sd_uhs2.h>
>
> +#include "card.h"
> #include "core.h"
> #include "bus.h"
> #include "sd.h"
> +#include "sd_ops.h"
> #include "mmc_ops.h"
>
> +#define UHS2_WAIT_CFG_COMPLETE_PERIOD_US (1 * 1000)
> +#define UHS2_WAIT_CFG_COMPLETE_TIMEOUT_MS 100
> +
> static const unsigned int sd_uhs2_freqs[] = { 52000000, 26000000 };
>
> +struct sd_uhs2_wait_active_state_data {
> + struct mmc_host *host;
> + struct mmc_command *cmd;
> +};
> +
> static int sd_uhs2_power_up(struct mmc_host *host)
> {
> int err;
> @@ -42,12 +70,51 @@ static int sd_uhs2_power_off(struct mmc_host *host)
>
> host->ios.vdd = 0;
> host->ios.clock = 0;
> - host->ios.timing = MMC_TIMING_LEGACY;
> + /* Must set UHS2 timing to identify UHS2 mode */
> + host->ios.timing = MMC_TIMING_UHS2_SPEED_A;
> host->ios.power_mode = MMC_POWER_OFF;
> + host->uhs2_sd_tran = false;
>
> return host->ops->uhs2_control(host, UHS2_SET_IOS);
> }
>
> +/*
> + * sd_uhs2_cmd_assemble() - build up UHS-II command packet which is embedded in
> + * mmc_command structure
> + * @cmd: MMC command to executed
> + * @uhs2_cmd: UHS2 command corresponded to MMC command
> + * @header: Header field of UHS-II command cxpacket
> + * @arg: Argument field of UHS-II command packet
> + * @payload: Payload field of UHS-II command packet
> + * @plen: Payload length
> + * @resp: Response buffer is allocated by caller and it is used to keep
> + * the response of CM-TRAN command. For SD-TRAN command, uhs2_resp
> + * should be null and SD-TRAN command response should be stored in
> + * resp of mmc_command.
> + * @resp_len: Response buffer length
> + *
> + * The uhs2_command structure contains message packets which are transmited/
> + * received on UHS-II bus. This function fills in the contents of uhs2_command
> + * structure and embededs UHS2 command into mmc_command structure, which is used
> + * in legacy SD operation functions.
> + *
> + */
> +static void sd_uhs2_cmd_assemble(struct mmc_command *cmd,
> + struct uhs2_command *uhs2_cmd,
> + u16 header, u16 arg, __be32 *payload,
> + u8 plen, u8 *resp, u8 resp_len)
> +{
> + uhs2_cmd->header = header;
> + uhs2_cmd->arg = arg;
> + uhs2_cmd->payload = payload;
> + uhs2_cmd->payload_len = plen * sizeof(u32);
> + uhs2_cmd->packet_len = uhs2_cmd->payload_len + 4;
> +
> + cmd->uhs2_cmd = uhs2_cmd;
> + cmd->uhs2_resp = resp;
> + cmd->uhs2_resp_len = resp_len;
> +}
> +
> /*
> * Run the phy initialization sequence, which mainly relies on the UHS-II host
> * to check that we reach the expected electrical state, between the host and
> @@ -55,7 +122,15 @@ static int sd_uhs2_power_off(struct mmc_host *host)
> */
> static int sd_uhs2_phy_init(struct mmc_host *host)
> {
> - return 0;
> + int err;
> +
> + err = host->ops->uhs2_control(host, UHS2_PHY_INIT);
> + if (err) {
> + pr_err("%s: failed to initial phy for UHS-II!\n",
> + mmc_hostname(host));
> + }
> +
> + return err;
> }
>
> /*
> @@ -64,6 +139,80 @@ static int sd_uhs2_phy_init(struct mmc_host *host)
> */
> static int sd_uhs2_dev_init(struct mmc_host *host)
> {
> + struct mmc_command cmd = {0};
> + struct uhs2_command uhs2_cmd = {};
> + u32 cnt;
> + u32 dap, gap, resp_gap;
> + u16 header, arg;
> + __be32 payload[UHS2_DEV_INIT_PAYLOAD_LEN];
> + u8 gd = 0;
> + u8 resp[UHS2_DEV_ENUM_RESP_LEN] = {0};
> + int err;
> +
> + dap = host->uhs2_caps.dap;
> + gap = host->uhs2_caps.gap;
> +
> + /*
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-21 to see DEVICE_INIT CCMD format.
> + * Head:
> + * - Control Write(R/W=1) with 4-Byte payload(PLEN=01b).
> + * - IOADR = CMD_BASE + 002h
> + * Payload:
> + * - bit [3:0] : GAP(Group Allocated Power)
> + * - bit [7:4] : GD(Group Descriptor)
> + * - bit [11] : Complete Flag
> + * - bit [15:12]: DAP(Device Allocated Power)
> + */
> + header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD;
> + arg = ((UHS2_DEV_CMD_DEVICE_INIT & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_4B |
> + (UHS2_DEV_CMD_DEVICE_INIT >> 8);
> +
> + /*
> + * Refer to UHS-II Addendum Version 1.02 section 6.3.1.
> + * Max. time from DEVICE_INIT CCMD EOP reception on Device
> + * Rx to its SOP transmission on Device Tx(Tfwd_init_cmd) is
> + * 1 second.
> + */
> + cmd.busy_timeout = 1000;
> +
> + /*
> + * Refer to UHS-II Addendum Version 1.02 section 6.2.6.3.
> + * Let's retry the DEVICE_INIT command no more than 30 times.
> + */
> + for (cnt = 0; cnt < 30; cnt++) {
> + payload[0] = ((dap & 0xF) << 12) |
> + UHS2_DEV_INIT_COMPLETE_FLAG |
> + ((gd & 0xF) << 4) |
> + (gap & 0xF);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg,
> + payload, UHS2_DEV_INIT_PAYLOAD_LEN,
> + resp, UHS2_DEV_INIT_RESP_LEN);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + if (resp[3] != (UHS2_DEV_CMD_DEVICE_INIT & 0xFF)) {
> + pr_err("%s: DEVICE_INIT response is wrong!\n",
> + mmc_hostname(host));
> + return -EIO;
> + }
> +
> + if (resp[5] & 0x8) {
> + host->uhs2_caps.group_desc = gd;
> + return 0;
> + }
> + resp_gap = resp[4] & 0x0F;
> + if (gap == resp_gap)
> + gd++;
> + }
> +
> return 0;
> }
>
> @@ -74,6 +223,52 @@ static int sd_uhs2_dev_init(struct mmc_host *host)
> */
> static int sd_uhs2_enum(struct mmc_host *host, u32 *node_id)
> {
> + struct mmc_command cmd = {0};
> + struct uhs2_command uhs2_cmd = {};
> + u16 header, arg;
> + __be32 payload[UHS2_DEV_ENUM_PAYLOAD_LEN];
> + u8 id_f = 0xF, id_l = 0x0;
> + u8 resp[UHS2_DEV_ENUM_RESP_LEN] = {0};
> + int err;
> +
> + /*
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-28 to see ENUMERATE CCMD format.
> + * Header:
> + * - Control Write(R/W=1) with 4-Byte payload(PLEN=01b).
> + * - IOADR = CMD_BASE + 003h
> + * Payload:
> + * - bit [3:0]: ID_L(Last Node ID)
> + * - bit [7:4]: ID_F(First Node ID)
> + */
> + header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD;
> + arg = ((UHS2_DEV_CMD_ENUMERATE & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_4B |
> + (UHS2_DEV_CMD_ENUMERATE >> 8);
> +
> + payload[0] = (id_f << 4) | id_l;
> + payload[0] = cpu_to_be32(payload[0]);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, UHS2_DEV_ENUM_PAYLOAD_LEN,
> + resp, UHS2_DEV_ENUM_RESP_LEN);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + if (resp[3] != (UHS2_DEV_CMD_ENUMERATE & 0xFF)) {
> + pr_err("%s: ENUMERATE response is wrong!\n",
> + mmc_hostname(host));
> + return -EIO;
> + }
> +
> + id_f = (resp[4] >> 4) & 0xF;
> + id_l = resp[4] & 0xF;
> + *node_id = id_f;
> +
> return 0;
> }
>
> @@ -84,6 +279,181 @@ static int sd_uhs2_enum(struct mmc_host *host, u32 *node_id)
> */
> static int sd_uhs2_config_read(struct mmc_host *host, struct mmc_card *card)
> {
> + struct mmc_command cmd = {0};
> + struct uhs2_command uhs2_cmd = {};
> + u16 header, arg;
> + u32 cap;
> + int err;
> +
> + /*
> + * Use Control Read CCMD to read Generic Capability from Configuration Register.
> + * - Control Write(R/W=1) with 4-Byte payload(PLEN=01b).
> + * - IOADR = Generic Capability Register(CFG_BASE + 000h)
> + */
> + header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD | card->uhs2_config.node_id;
> + arg = ((UHS2_DEV_CONFIG_GEN_CAPS & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_READ |
> + UHS2_NATIVE_CMD_PLEN_4B |
> + (UHS2_DEV_CONFIG_GEN_CAPS >> 8);
> +
> + /*
> + * There is no payload because per spec, there should be
> + * no payload field for read CCMD.
> + * Plen is set in arg. Per spec, plen for read CCMD
> + * represents the len of read data which is assigned in payload
> + * of following RES (p136).
> + */
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /*
> + * Generic Capability Register:
> + * bit [7:0] : Reserved
> + * bit [13:8] : Device-Specific Number of Lanes and Functionality
> + * bit 8: 2L-HD
> + * bit 9: 2D-1U FD
> + * bit 10: 1D-2U FD
> + * bit 11: 2D-2U FD
> + * Others: Reserved
> + * bit [14] : DADR Length
> + * 0: 4 bytes
> + * 1: Reserved
> + * bit [23:16]: Application Type
> + * bit 16: 0=Non-SD memory, 1=SD memory
> + * bit 17: 0=Non-SDIO, 1=SDIO
> + * bit 18: 0=Card, 1=Embedded
> + * bit [63:24]: Reserved
> + */
> + cap = cmd.resp[0];
> + card->uhs2_config.n_lanes =
> + (cap >> UHS2_DEV_CONFIG_N_LANES_POS) &
> + UHS2_DEV_CONFIG_N_LANES_MASK;
> + card->uhs2_config.dadr_len =
> + (cap >> UHS2_DEV_CONFIG_DADR_POS) &
> + UHS2_DEV_CONFIG_DADR_MASK;
> + card->uhs2_config.app_type =
> + (cap >> UHS2_DEV_CONFIG_APP_POS) &
> + UHS2_DEV_CONFIG_APP_MASK;
> +
> + /*
> + * Use Control Read CCMD to read PHY Capability from Configuration Register.
> + * - Control Write(R/W=1) with 8-Byte payload(PLEN=10b).
> + * - IOADR = PHY Capability Register(CFG_BASE + 002h)
> + */
> + arg = ((UHS2_DEV_CONFIG_PHY_CAPS & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_READ |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_PHY_CAPS >> 8);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /*
> + * PHY Capability Register:
> + * bit [3:0] : PHY Minor Revision
> + * bit [5:4] : PHY Major Revision
> + * bit [15] : Support Hibernate Mode
> + * 0: Not support Hibernate Mode
> + * 1: Support Hibernate Mode
> + * bit [31:16]: Reserved
> + * bit [35:32]: Device-Specific N_LSS_SYN
> + * bit [39:36]: Device-Specific N_LSS_DIR
> + * bit [63:40]: Reserved
> + */
> + cap = cmd.resp[0];
> + card->uhs2_config.phy_minor_rev =
> + cap & UHS2_DEV_CONFIG_PHY_MINOR_MASK;
> + card->uhs2_config.phy_major_rev =
> + (cap >> UHS2_DEV_CONFIG_PHY_MAJOR_POS) &
> + UHS2_DEV_CONFIG_PHY_MAJOR_MASK;
> + card->uhs2_config.can_hibernate =
> + (cap >> UHS2_DEV_CONFIG_CAN_HIBER_POS) &
> + UHS2_DEV_CONFIG_CAN_HIBER_MASK;
> +
> + cap = cmd.resp[1];
> + card->uhs2_config.n_lss_sync =
> + cap & UHS2_DEV_CONFIG_N_LSS_SYN_MASK;
> + card->uhs2_config.n_lss_dir =
> + (cap >> UHS2_DEV_CONFIG_N_LSS_DIR_POS) &
> + UHS2_DEV_CONFIG_N_LSS_DIR_MASK;
> + if (card->uhs2_config.n_lss_sync == 0)
> + card->uhs2_config.n_lss_sync = 16 << 2;
> + else
> + card->uhs2_config.n_lss_sync <<= 2;
> +
> + if (card->uhs2_config.n_lss_dir == 0)
> + card->uhs2_config.n_lss_dir = 16 << 3;
> + else
> + card->uhs2_config.n_lss_dir <<= 3;
> +
> + /*
> + * Use Control Read CCMD to read LINK/TRAN Capability from Configuration Register.
> + * - Control Write(R/W=1) with 8-Byte payload(PLEN=10b).
> + * - IOADR = LINK/TRAN Capability Register(CFG_BASE + 004h)
> + */
> + arg = ((UHS2_DEV_CONFIG_LINK_TRAN_CAPS & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_READ |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_LINK_TRAN_CAPS >> 8);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /*
> + * LINK/TRAN Capability Register:
> + * bit [3:0] : LINK_TRAN Minor Revision
> + * bit [5:4] : LINK/TRAN Major Revision
> + * bit [7:6] : Reserved
> + * bit [15:8] : Device-Specific N_FCU
> + * bit [18:16]: Device Type
> + * 001b=Host
> + * 010b=Device
> + * 011b=Reserved for CMD issuable Device
> + * bit [19] : Reserved
> + * bit [31:20]: Device-Specific MAX_BLKLEN
> + * bit [39:32]: Device-Specific N_DATA_GAP
> + * bit [63:40]: Reserved
> + */
> + cap = cmd.resp[0];
> + card->uhs2_config.link_minor_rev =
> + cap & UHS2_DEV_CONFIG_LT_MINOR_MASK;
> + card->uhs2_config.link_major_rev =
> + (cap >> UHS2_DEV_CONFIG_LT_MAJOR_POS) &
> + UHS2_DEV_CONFIG_LT_MAJOR_MASK;
> + card->uhs2_config.n_fcu =
> + (cap >> UHS2_DEV_CONFIG_N_FCU_POS) &
> + UHS2_DEV_CONFIG_N_FCU_MASK;
> + card->uhs2_config.dev_type =
> + (cap >> UHS2_DEV_CONFIG_DEV_TYPE_POS) &
> + UHS2_DEV_CONFIG_DEV_TYPE_MASK;
> + card->uhs2_config.maxblk_len =
> + (cap >> UHS2_DEV_CONFIG_MAX_BLK_LEN_POS) &
> + UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK;
> +
> + cap = cmd.resp[1];
> + card->uhs2_config.n_data_gap =
> + cap & UHS2_DEV_CONFIG_N_DATA_GAP_MASK;
> + if (card->uhs2_config.n_fcu == 0)
> + card->uhs2_config.n_fcu = 256;
> +
> return 0;
> }
>
> @@ -98,26 +468,357 @@ static int sd_uhs2_config_read(struct mmc_host *host, struct mmc_card *card)
> */
> static int sd_uhs2_config_write(struct mmc_host *host, struct mmc_card *card)
> {
> + struct mmc_command cmd = {0};
> + struct uhs2_command uhs2_cmd = {};
> + u16 header, arg;
> + __be32 payload[UHS2_CFG_WRITE_PAYLOAD_LEN];
> + u8 nMinDataGap;
> + int err;
> + u8 resp[5] = {0};
> +
> + /*
> + * Use Control Write CCMD to set Generic Setting in Configuration Register.
> + * - Control Write(R/W=1) with 8-Byte payload(PLEN=10b).
> + * - IOADR = Generic Setting Register(CFG_BASE + 008h)
> + * - Payload = New contents to be written to Generic Setting Register
> + */
> + header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD | card->uhs2_config.node_id;
> + arg = ((UHS2_DEV_CONFIG_GEN_SET & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_GEN_SET >> 8);
> +
> + /*
> + * Most UHS-II cards only support FD and 2L-HD mode. Other lane numbers
> + * defined in UHS-II addendem Ver1.01 are optional.
> + */
> + host->uhs2_caps.n_lanes_set = UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD;
> + card->uhs2_config.n_lanes_set = UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD;
> +
> + payload[0] = card->uhs2_config.n_lanes_set << UHS2_DEV_CONFIG_N_LANES_POS;
> + payload[1] = 0;
> + payload[0] = cpu_to_be32(payload[0]);
> + payload[1] = cpu_to_be32(payload[1]);
> +
> + /*
> + * There is no payload because per spec, there should be
> + * no payload field for read CCMD.
> + * Plen is set in arg. Per spec, plen for read CCMD
> + * represents the len of read data which is assigned in payload
> + * of following RES (p136).
> + */
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, UHS2_CFG_WRITE_PAYLOAD_LEN,
> + NULL, 0);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /*
> + * Use Control Write CCMD to set PHY Setting in Configuration Register.
> + * - Control Write(R/W=1) with 8-Byte payload(PLEN=10b).
> + * - IOADR = PHY Setting Register(CFG_BASE + 00Ah)
> + * - Payload = New contents to be written to PHY Setting Register
> + */
> + arg = ((UHS2_DEV_CONFIG_PHY_SET & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_PHY_SET >> 8);
> +
> + if (host->uhs2_caps.speed_range == UHS2_DEV_CONFIG_PHY_SET_SPEED_B) {
> + if (card->uhs2_config.n_lanes == UHS2_DEV_CONFIG_2L_HD_FD &&
> + host->uhs2_caps.n_lanes == UHS2_DEV_CONFIG_2L_HD_FD) {
> + /* Support HD */
> + host->ios.timing = MMC_TIMING_UHS2_SPEED_B_HD;
> + nMinDataGap = 1;
> + } else {
> + /* Only support 2L-FD so far */
> + host->ios.timing = MMC_TIMING_UHS2_SPEED_B;
> + nMinDataGap = 3;
> + }
> + card->uhs2_config.speed_range_set = UHS2_DEV_CONFIG_PHY_SET_SPEED_B;
> + } else {
> + if (card->uhs2_config.n_lanes == UHS2_DEV_CONFIG_2L_HD_FD &&
> + host->uhs2_caps.n_lanes == UHS2_DEV_CONFIG_2L_HD_FD) {
> + /* Support HD */
> + host->ios.timing = MMC_TIMING_UHS2_SPEED_A_HD;
> + nMinDataGap = 1;
> + } else {
> + /* Only support 2L-FD so far */
> + host->ios.timing = MMC_TIMING_UHS2_SPEED_A;
> + nMinDataGap = 3;
> + }
> + card->uhs2_config.speed_range_set = UHS2_DEV_CONFIG_PHY_SET_SPEED_A;
> + }
> +
> + payload[0] = card->uhs2_config.speed_range_set << UHS2_DEV_CONFIG_PHY_SET_SPEED_POS;
> +
> + card->uhs2_config.n_lss_sync_set = (max(card->uhs2_config.n_lss_sync,
> + host->uhs2_caps.n_lss_sync) >> 2) &
> + UHS2_DEV_CONFIG_N_LSS_SYN_MASK;
> + host->uhs2_caps.n_lss_sync_set = card->uhs2_config.n_lss_sync_set;
> +
> + card->uhs2_config.n_lss_dir_set = (max(card->uhs2_config.n_lss_dir,
> + host->uhs2_caps.n_lss_dir) >> 3) &
> + UHS2_DEV_CONFIG_N_LSS_DIR_MASK;
> + host->uhs2_caps.n_lss_dir_set = card->uhs2_config.n_lss_dir_set;
> +
> + payload[1] = (card->uhs2_config.n_lss_dir_set << UHS2_DEV_CONFIG_N_LSS_DIR_POS) |
> + card->uhs2_config.n_lss_sync_set;
> + payload[0] = cpu_to_be32(payload[0]);
> + payload[1] = cpu_to_be32(payload[1]);
> +
> + memset(resp, 0, sizeof(resp));
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, UHS2_CFG_WRITE_PAYLOAD_LEN,
> + resp, UHS2_CFG_WRITE_PHY_SET_RESP_LEN);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + if ((resp[2] & 0x80)) {
> + pr_err("%s: %s: UHS2 CMD not accepted, resp= 0x%x!\n",
> + mmc_hostname(host), __func__, resp[2]);
> + return -EIO;
> + }
> +
> + /*
> + * Use Control Write CCMD to set LINK/TRAN Setting in Configuration Register.
> + * - Control Write(R/W=1) with 8-Byte payload(PLEN=10b).
> + * - IOADR = LINK/TRAN Setting Register(CFG_BASE + 00Ch)
> + * - Payload = New contents to be written to LINK/TRAN Setting Register
> + */
> + arg = ((UHS2_DEV_CONFIG_LINK_TRAN_SET & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_LINK_TRAN_SET >> 8);
> +
> + if (card->uhs2_config.app_type == UHS2_DEV_CONFIG_APP_SD_MEM)
> + card->uhs2_config.maxblk_len_set = UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN;
> + else
> + card->uhs2_config.maxblk_len_set = min(card->uhs2_config.maxblk_len,
> + host->uhs2_caps.maxblk_len);
> + host->uhs2_caps.maxblk_len_set = card->uhs2_config.maxblk_len_set;
> +
> + card->uhs2_config.n_fcu_set = min(card->uhs2_config.n_fcu, host->uhs2_caps.n_fcu);
> + host->uhs2_caps.n_fcu_set = card->uhs2_config.n_fcu_set;
> +
> + card->uhs2_config.n_data_gap_set = max(nMinDataGap, card->uhs2_config.n_data_gap);
> + host->uhs2_caps.n_data_gap_set = card->uhs2_config.n_data_gap_set;
> +
> + host->uhs2_caps.max_retry_set = 3;
> + card->uhs2_config.max_retry_set = host->uhs2_caps.max_retry_set;
> +
> + payload[0] = (card->uhs2_config.maxblk_len_set << UHS2_DEV_CONFIG_MAX_BLK_LEN_POS) |
> + (card->uhs2_config.max_retry_set << UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS) |
> + (card->uhs2_config.n_fcu_set << UHS2_DEV_CONFIG_N_FCU_POS);
> + payload[1] = card->uhs2_config.n_data_gap_set;
> + payload[0] = cpu_to_be32(payload[0]);
> + payload[1] = cpu_to_be32(payload[1]);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, UHS2_CFG_WRITE_PAYLOAD_LEN,
> + NULL, 0);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /*
> + * Use Control Write CCMD to set Config Completion(payload bit 63) in Generic Setting
> + * Register.
> + * Header:
> + * - Control Write(R/W=1) with 8-Byte payload(PLEN=10b).
> + * - IOADR = PGeneric Setting Register(CFG_BASE + 008h)
> + * Payload:
> + * - bit [63]: Config Completion
> + *
> + * DLSM transits to Active state immediately when Config Completion is set to 1.
> + */
> + arg = ((UHS2_DEV_CONFIG_GEN_SET & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_GEN_SET >> 8);
> +
> + payload[0] = 0;
> + payload[1] = UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE;
> + payload[0] = cpu_to_be32(payload[0]);
> + payload[1] = cpu_to_be32(payload[1]);
> +
> + memset(resp, 0, sizeof(resp));
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, UHS2_CFG_WRITE_PAYLOAD_LEN,
> + resp, UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /* Set host Config Setting registers */
> + err = host->ops->uhs2_control(host, UHS2_SET_CONFIG);
> + if (err) {
> + pr_err("%s: %s: UHS2 SET_CONFIG fail!\n", mmc_hostname(host), __func__);
> + return err;
> + }
> +
> return 0;
> }
>
> -/*
> - * Initialize the UHS-II card through the SD-TRAN transport layer. This enables
> - * commands/requests to be backwards compatible through the legacy SD protocol.
> - * UHS-II cards has a specific power limit specified for VDD1/VDD2, that should
> - * be set through a legacy CMD6. Note that, the power limit that becomes set,
> - * survives a soft reset through the GO_DORMANT_STATE command.
> - */
> -static int sd_uhs2_legacy_init(struct mmc_host *host, struct mmc_card *card)
> +static int sd_uhs2_go_dormant(struct mmc_host *host, u32 node_id)
> +{
> + struct mmc_command cmd = {0};
> + struct uhs2_command uhs2_cmd = {};
> + u16 header, arg;
> + __be32 payload[1];
> + int err;
> +
> + /* Disable Normal INT */
> + err = host->ops->uhs2_control(host, UHS2_DISABLE_INT);
> + if (err) {
> + pr_err("%s: %s: UHS2 DISABLE_INT fail!\n",
> + mmc_hostname(host), __func__);
> + return err;
> + }
> +
> + /*
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-17 to see GO_DORMANT_STATE CCMD format.
> + * Header:
> + * - Control Write(R/W=1) with 4-Byte payload(PLEN=01b).
> + * - IOADR = CMD_BASE + 001h
> + * Payload:
> + * - bit [7]: HBR(Entry to Hibernate Mode)
> + * 1: Host intends to enter Hibernate mode during Dormant state.
> + * The default setting is 0 because hibernate is currently not supported.
> + */
> + header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD | node_id;
> + arg = ((UHS2_DEV_CMD_GO_DORMANT_STATE & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_WRITE |
> + UHS2_NATIVE_CMD_PLEN_4B |
> + (UHS2_DEV_CMD_GO_DORMANT_STATE >> 8);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, UHS2_GO_DORMANT_PAYLOAD_LEN,
> + NULL, 0);
> +
> + err = mmc_wait_for_cmd(host, &cmd, 0);
> + if (err) {
> + pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /* Check Dormant State in Present */
> + err = host->ops->uhs2_control(host, UHS2_CHECK_DORMANT);
> + if (err)
> + return err;
> +
> + /* Disable UHS2 card clock */
> + err = host->ops->uhs2_control(host, UHS2_DISABLE_CLK);
> + if (err)
> + return err;
> +
> + /* Restore sd clock */
> + mmc_delay(5);
> + err = host->ops->uhs2_control(host, UHS2_ENABLE_CLK);
> + if (err)
> + return err;
> +
> + /* Enable Normal INT */
> + err = host->ops->uhs2_control(host, UHS2_ENABLE_INT);
> + if (err)
> + return err;
> +
> + /* Detect UHS2 */
> + err = host->ops->uhs2_control(host, UHS2_PHY_INIT);
> + if (err)
> + return err;
> +
> + return 0;
> +}
> +
> +static int sd_uhs2_wait_active_state_cb(void *cb_data, bool *busy)
> {
> + struct sd_uhs2_wait_active_state_data *data = cb_data;
> + struct mmc_host *host = data->host;
> + struct mmc_command *cmd = data->cmd;
> + int err;
> +
> + err = mmc_wait_for_cmd(host, cmd, 0);
> + if (err)
> + return err;
> +
> + if (cmd->resp[1] & UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE)
> + *busy = false;
> + else
> + *busy = true;
> +
> return 0;
> }
>
> +static int sd_uhs2_go_dormant_state(struct mmc_host *host, u32 node_id)
> +{
> + struct mmc_command cmd = {0};
> + struct uhs2_command uhs2_cmd = {};
> + u16 header, arg;
> + int err;
> + struct sd_uhs2_wait_active_state_data cb_data = {
> + .host = host,
> + .cmd = &cmd
> + };
> +
> + err = sd_uhs2_go_dormant(host, node_id);
> + if (err) {
> + pr_err("%s: %s: UHS2 GO_DORMANT_STATE fail, err= 0x%x!\n",
> + mmc_hostname(host), __func__, err);
> + return err;
> + }
> +
> + /*
> + * Use Control Read CCMD to check Config Completion(bit 63) in Generic Setting Register.
> + * - Control Read(R/W=0) with 8-Byte payload(PLEN=10b).
> + * - IOADR = Generic Setting Register(CFG_BASE + 008h)
> + *
> + * When UHS-II card been switched to new speed mode, it will set Config Completion to 1.
> + */
> + header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD | node_id;
> + arg = ((UHS2_DEV_CONFIG_GEN_SET & 0xFF) << 8) |
> + UHS2_NATIVE_CMD_READ |
> + UHS2_NATIVE_CMD_PLEN_8B |
> + (UHS2_DEV_CONFIG_GEN_SET >> 8);
> +
> + sd_uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
> + err = __mmc_poll_for_busy(host, UHS2_WAIT_CFG_COMPLETE_PERIOD_US,
> + UHS2_WAIT_CFG_COMPLETE_TIMEOUT_MS,
> + &sd_uhs2_wait_active_state_cb, &cb_data);
> + if (err) {
> + pr_err("%s: %s: Not switch to Active in 100 ms\n", mmc_hostname(host), __func__);
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +static void sd_uhs2_remove(struct mmc_host *host)
> +{
> + mmc_remove_card(host->card);
> + host->card = NULL;
> +}
> +
> /*
> * Allocate the data structure for the mmc_card and run the UHS-II specific
> * initialization sequence.
> */
> -static int sd_uhs2_init_card(struct mmc_host *host)
> +static int sd_uhs2_init_card(struct mmc_host *host, struct mmc_card *oldcard)
> {
> struct mmc_card *card;
> u32 node_id;
> @@ -131,9 +832,14 @@ static int sd_uhs2_init_card(struct mmc_host *host)
> if (err)
> return err;
>
> - card = mmc_alloc_card(host, &sd_type);
> - if (IS_ERR(card))
> - return PTR_ERR(card);
> + if (oldcard) {
> + card = oldcard;
> + } else {
> + card = mmc_alloc_card(host, &sd_type);
> + if (IS_ERR(card))
> + return PTR_ERR(card);
> + }
> + host->card = card;
>
> card->uhs2_config.node_id = node_id;
> card->type = MMC_TYPE_SD;
> @@ -146,18 +852,189 @@ static int sd_uhs2_init_card(struct mmc_host *host)
> if (err)
> goto err;
>
> - host->card = card;
> + /* If change speed to Range B, need to GO_DORMANT_STATE */
> + if (host->ios.timing == MMC_TIMING_UHS2_SPEED_B ||
> + host->ios.timing == MMC_TIMING_UHS2_SPEED_B_HD) {
> + err = sd_uhs2_go_dormant_state(host, node_id);
> + if (err)
> + goto err;
> + }
> +
> + host->uhs2_sd_tran = true;
> +
> return 0;
>
> err:
> - mmc_remove_card(card);
> + if (!oldcard)
> + mmc_remove_card(card);
> + else
> + sd_uhs2_remove(host);
> return err;
> }
>
> -static void sd_uhs2_remove(struct mmc_host *host)
> +/*
> + * Initialize the UHS-II card through the SD-TRAN transport layer. This enables
> + * commands/requests to be backwards compatible through the legacy SD protocol.
> + * UHS-II cards has a specific power limit specified for VDD1/VDD2, that should
> + * be set through a legacy CMD6. Note that, the power limit that becomes set,
> + * survives a soft reset through the GO_DORMANT_STATE command.
> + */
> +static int sd_uhs2_legacy_init(struct mmc_host *host, struct mmc_card *card)
> {
> - mmc_remove_card(host->card);
> - host->card = NULL;
> + int err;
> + u32 cid[4];
> + u32 ocr;
> + u32 rocr;
> + u8 *status;
> + int ro;
> +
> + /* Send CMD0 to reset SD card */
> + err = __mmc_go_idle(host);
> + if (err)
> + return err;
> +
> + mmc_delay(1);
> +
> + /* Send CMD8 to communicate SD interface operation condition */
> + err = mmc_send_if_cond(host, host->ocr_avail);
> + if (err) {
> + dev_warn(mmc_dev(host), "CMD8 error\n");
> + goto err;
> + }
> +
> + /*
> + * Probe SD card working voltage.
> + */
> + err = mmc_send_app_op_cond(host, 0, &ocr);
> + if (err)
> + goto err;
> +
> + card->ocr = ocr;
> +
> + /*
> + * Some SD cards claims an out of spec VDD voltage range. Let's treat
> + * these bits as being in-valid and especially also bit7.
> + */
> + ocr &= ~0x7FFF;
> + rocr = mmc_select_voltage(host, ocr);
> + /*
> + * Some cards have zero value of rocr in UHS-II mode. Assign host's
> + * ocr value to rocr.
> + */
> + if (!rocr)
> + rocr = host->ocr_avail;
> +
> + rocr |= (SD_OCR_CCS | SD_OCR_XPC);
> +
> + /* Wait SD power on ready */
> + ocr = rocr;
> +
> + err = mmc_send_app_op_cond(host, ocr, &rocr);
> + if (err)
> + goto err;
> +
> + err = mmc_send_cid(host, cid);
> + if (err)
> + goto err;
> +
> + memcpy(card->raw_cid, cid, sizeof(card->raw_cid));
> + mmc_decode_cid(card);
> +
> + /*
> + * For native busses: get card RCA and quit open drain mode.
> + */
> + err = mmc_send_relative_addr(host, &card->rca);
> + if (err)
> + goto err;
> +
> + err = mmc_sd_get_csd(card);
> + if (err)
> + goto err;
> +
> + /*
> + * Select card, as all following commands rely on that.
> + */
> + err = mmc_select_card(card);
> + if (err)
> + goto err;
> +
> + /*
> + * Fetch SCR from card.
> + */
> + err = mmc_app_send_scr(card);
> + if (err)
> + goto err;
> +
> + err = mmc_decode_scr(card);
> + if (err)
> + goto err;
> +
> + /*
> + * Switch to high power consumption mode.
> + * Even switch failed, sd card can still work at lower power consumption mode, but
> + * performance will be lower than high power consumption mode.
> + */
> + status = kmalloc(64, GFP_KERNEL);
> + if (!status)
> + return -ENOMEM;
> +
> + if (!(card->csd.cmdclass & CCC_SWITCH)) {
> + pr_warn("%s: card lacks mandatory switch function, performance might suffer\n",
> + mmc_hostname(card->host));
> + } else {
> + /* send CMD6 to set Maximum Power Consumption to get better performance */
> + err = mmc_sd_switch(card, 0, 3, SD4_SET_POWER_LIMIT_1_80W, status);
> + if (!err)
> + err = mmc_sd_switch(card, 1, 3, SD4_SET_POWER_LIMIT_1_80W, status);
> +
> + err = 0;
> + }
> +
> + /*
> + * Check if read-only switch is active.
> + */
> + ro = mmc_sd_get_ro(host);
> + if (ro < 0) {
> + pr_warn("%s: host does not support read-only switch, assuming write-enable\n",
> + mmc_hostname(host));
> + } else if (ro > 0) {
> + mmc_card_set_readonly(card);
> + }
> +
> + /*
> + * NOTE:
> + * Should we read Externsion Register to check power notification feature here?
> + */
> +
> + kfree(status);
> +
> + return 0;
> +
> +err:
> + sd_uhs2_remove(host);
> + return err;
> +}
> +
> +int sd_uhs2_reinit(struct mmc_host *host)
> +{
> + struct mmc_card *card = host->card;
> + int err;
> +
> + sd_uhs2_power_up(host);
> + err = sd_uhs2_phy_init(host);
> + if (err)
> + return err;
> +
> + err = sd_uhs2_init_card(host, card);
> + if (err)
> + return err;
> +
> + err = sd_uhs2_legacy_init(host, card);
> + if (err)
> + return err;
> +
> + mmc_card_set_present(card);
> + return err;
> }
>
> static int sd_uhs2_alive(struct mmc_host *host)
> @@ -179,38 +1056,195 @@ static void sd_uhs2_detect(struct mmc_host *host)
> mmc_claim_host(host);
> mmc_detach_bus(host);
> sd_uhs2_power_off(host);
> + /* Remove UHS2 timing to indicate the end of UHS2 mode */
> + host->ios.timing = MMC_TIMING_LEGACY;
> mmc_release_host(host);
> }
> }
>
> +static int _sd_uhs2_suspend(struct mmc_host *host)
> +{
> + struct mmc_card *card = host->card;
> + int err = 0;
> +
> + mmc_claim_host(host);
> +
> + if (mmc_card_suspended(card))
> + goto out;
> +
> + if (mmc_sd_can_poweroff_notify(card))
> + err = sd_poweroff_notify(card);
> +
> + if (!err) {
> + sd_uhs2_power_off(host);
> + mmc_card_set_suspended(card);
> + }
> +
> +out:
> + mmc_release_host(host);
> + return err;
> +}
> +
> +/*
> + * Callback for suspend
> + */
> static int sd_uhs2_suspend(struct mmc_host *host)
> {
> - return 0;
> + int err;
> +
> + err = _sd_uhs2_suspend(host);
> + if (!err) {
> + pm_runtime_disable(&host->card->dev);
> + pm_runtime_set_suspended(&host->card->dev);
> + }
> +
> + return err;
> +}
> +
> +/*
> + * This function tries to determine if the same card is still present
> + * and, if so, restore all state to it.
> + */
> +static int _mmc_sd_uhs2_resume(struct mmc_host *host)
> +{
> + int err = 0;
> +
> + mmc_claim_host(host);
> +
> + if (!mmc_card_suspended(host->card))
> + goto out;
> +
> + /* Power up UHS2 SD card and re-initialize it. */
> + err = sd_uhs2_reinit(host);
> + mmc_card_clr_suspended(host->card);
> +
> +out:
> + mmc_release_host(host);
> + return err;
> }
>
> +/*
> + * Callback for resume
> + */
> static int sd_uhs2_resume(struct mmc_host *host)
> {
> + pm_runtime_enable(&host->card->dev);
> return 0;
> }
>
> +/*
> + * Callback for runtime_suspend.
> + */
> static int sd_uhs2_runtime_suspend(struct mmc_host *host)
> {
> - return 0;
> + int err;
> +
> + if (!(host->caps & MMC_CAP_AGGRESSIVE_PM))
> + return 0;
> +
> + err = _sd_uhs2_suspend(host);
> + if (err)
> + pr_err("%s: error %d doing aggressive suspend\n", mmc_hostname(host), err);
> +
> + return err;
> }
>
> static int sd_uhs2_runtime_resume(struct mmc_host *host)
> {
> - return 0;
> + int err;
> +
> + err = _mmc_sd_uhs2_resume(host);
> + if (err && err != -ENOMEDIUM)
> + pr_err("%s: error %d doing runtime resume\n", mmc_hostname(host), err);
> +
> + return err;
> }
>
> -static int sd_uhs2_shutdown(struct mmc_host *host)
> +static int sd_uhs2_hw_reset(struct mmc_host *host)
> {
> - return 0;
> + int err;
> +
> + sd_uhs2_power_off(host);
> + /* Wait at least 1 ms according to SD spec */
> + mmc_delay(1);
> + sd_uhs2_power_up(host);
> +
> + err = sd_uhs2_reinit(host);
> +
> + return err;
> }
>
> -static int sd_uhs2_hw_reset(struct mmc_host *host)
> +/*
> + * mmc_uhs2_prepare_cmd - prepare for SD command packet
> + * @host: MMC host
> + * @mrq: MMC request
> + *
> + * Initialize and fill in a header and a payload of SD command packet.
> + * The caller should allocate uhs2_command in host->cmd->uhs2_cmd in
> + * advance.
> + *
> + * Return: 0 on success, non-zero error on failure
> + */
> +void mmc_uhs2_prepare_cmd(struct mmc_host *host, struct mmc_request *mrq)
> {
> - return 0;
> + struct mmc_command *cmd;
> + struct uhs2_command *uhs2_cmd;
> + u16 header, arg;
> + __be32 *payload;
> + u8 plen;
> +
> + cmd = mrq->cmd;
> + header = host->card->uhs2_config.node_id;
> + if ((cmd->flags & MMC_CMD_MASK) == MMC_CMD_ADTC)
> + header |= UHS2_PACKET_TYPE_DCMD;
> + else
> + header |= UHS2_PACKET_TYPE_CCMD;
> +
> + arg = cmd->opcode << UHS2_SD_CMD_INDEX_POS;
> + if (host->uhs2_app_cmd) {
> + arg |= UHS2_SD_CMD_APP;
> + host->uhs2_app_cmd = false;
> + }
> +
> + /*
> + * UHS-II Addendum 7.2.1.2
> + * Host may set DM to 1 for DCMD which supports multi-block read/write regardless of
> + * data transfer length (e.g., CMD18, CMD25). Otherwise, it shall not set DM to 1.
> + * (e.g., CMD6, CMD17, CMD24). These rules are also applied to other multi-block read/write
> + * commands defined in other Part of SD specifications (for example, Host may set DM to 1
> + * for ACMD18 or ACMD25).
> + */
> + if (mmc_op_multi(cmd->opcode))
> + cmd->uhs2_cmd->tmode_half_duplex = mmc_card_uhs2_hd_mode(host);
> + else
> + cmd->uhs2_cmd->tmode_half_duplex = 0;
> +
> + uhs2_cmd = cmd->uhs2_cmd;
> + payload = uhs2_cmd->payload;
> + plen = 2; /* at the maximum */
> +
> + if ((cmd->flags & MMC_CMD_MASK) == MMC_CMD_ADTC &&
> + cmd->uhs2_cmd->tmode_half_duplex) {
> + if (mmc_card_uhs2_hd_mode(host))
> + arg |= UHS2_DCMD_2L_HD_MODE;
> +
> + arg |= UHS2_DCMD_LM_TLEN_EXIST;
> +
> + if (cmd->data->blocks == 1 &&
> + cmd->data->blksz != 512 &&
> + cmd->opcode != MMC_READ_SINGLE_BLOCK &&
> + cmd->opcode != MMC_WRITE_BLOCK) {
> + arg |= UHS2_DCMD_TLUM_BYTE_MODE;
> + payload[1] = cpu_to_be32(cmd->data->blksz);
> + } else {
> + payload[1] = cpu_to_be32(cmd->data->blocks);
> + }
> + } else {
> + plen = 1;
> + }
> +
> + payload[0] = cpu_to_be32(cmd->arg);
> + sd_uhs2_cmd_assemble(cmd, uhs2_cmd, header, arg, payload, plen, NULL, 0);
> }
>
> static const struct mmc_bus_ops sd_uhs2_ops = {
> @@ -221,7 +1255,7 @@ static const struct mmc_bus_ops sd_uhs2_ops = {
> .resume = sd_uhs2_resume,
> .runtime_suspend = sd_uhs2_runtime_suspend,
> .runtime_resume = sd_uhs2_runtime_resume,
> - .shutdown = sd_uhs2_shutdown,
> + .shutdown = sd_uhs2_suspend,
> .hw_reset = sd_uhs2_hw_reset,
> };
>
> @@ -237,7 +1271,7 @@ static int sd_uhs2_attach(struct mmc_host *host)
> if (err)
> goto err;
>
> - err = sd_uhs2_init_card(host);
> + err = sd_uhs2_init_card(host, NULL);
> if (err)
> goto err;
>
> @@ -254,21 +1288,33 @@ static int sd_uhs2_attach(struct mmc_host *host)
> goto remove_card;
>
> mmc_claim_host(host);
> +
> return 0;
>
> remove_card:
> - mmc_remove_card(host->card);
> - host->card = NULL;
> + sd_uhs2_remove(host);
> mmc_claim_host(host);
> - mmc_detach_bus(host);
> +
> err:
> + mmc_detach_bus(host);
> sd_uhs2_power_off(host);
> + /* Remove UHS2 timing to indicate the end of UHS2 mode */
> + host->ios.timing = MMC_TIMING_LEGACY;
> return err;
> }
>
> +/**
> + * mmc_attach_sd_uhs2 - select UHS2 interface
> + * @host: MMC host
> + *
> + * Try to select UHS2 interface and initialize the bus for a given
> + * frequency, @freq.
> + *
> + * Return: 0 on success, non-zero error on failure
> + */
> int mmc_attach_sd_uhs2(struct mmc_host *host)
> {
> - int i, err = 0;
> + int i, err;
>
> if (!(host->caps2 & MMC_CAP2_SD_UHS2))
> return -EOPNOTSUPP;
> @@ -283,6 +1329,9 @@ int mmc_attach_sd_uhs2(struct mmc_host *host)
> */
> for (i = 0; i < ARRAY_SIZE(sd_uhs2_freqs); i++) {
> host->f_init = sd_uhs2_freqs[i];
> + pr_debug("%s: %s: trying to init UHS-II card at %u Hz\n",
> + mmc_hostname(host), __func__, host->f_init);
> +
> err = sd_uhs2_attach(host);
> if (!err)
> break;
> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> index 2c7928a50907..f30f6be86f66 100644
> --- a/include/linux/mmc/core.h
> +++ b/include/linux/mmc/core.h
> @@ -23,6 +23,15 @@ enum mmc_blk_status {
> MMC_BLK_NEW_REQUEST,
> };
>
> +struct uhs2_command {
> + u16 header;
> + u16 arg;
> + __be32 *payload;
> + u32 payload_len;
> + u32 packet_len;
> + u8 tmode_half_duplex;
> +};
> +
> struct mmc_command {
> u32 opcode;
> u32 arg;
> @@ -108,6 +117,10 @@ struct mmc_command {
> unsigned int busy_timeout; /* busy detect timeout in ms */
> struct mmc_data *data; /* data segment associated with cmd */
> struct mmc_request *mrq; /* associated request */
> +
> + struct uhs2_command *uhs2_cmd; /* UHS2 command */
> + u8 *uhs2_resp; /* UHS2 native cmd resp */
> + u8 uhs2_resp_len; /* UHS2 native cmd resp len */
> };
>
> struct mmc_data {
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 68e78c65cf1c..899bb5d247d3 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -126,6 +126,13 @@ struct sd_uhs2_caps {
> };
>
> enum sd_uhs2_operation {
> + UHS2_PHY_INIT = 0,
> + UHS2_SET_CONFIG,
> + UHS2_ENABLE_INT,
> + UHS2_DISABLE_INT,
> + UHS2_ENABLE_CLK,
> + UHS2_DISABLE_CLK,
> + UHS2_CHECK_DORMANT,
> UHS2_SET_IOS,
> };
>
> @@ -476,6 +483,8 @@ struct mmc_host {
> #endif
> #define MMC_CAP2_ALT_GPT_TEGRA (1 << 28) /* Host with eMMC that has GPT entry at a non-standard location */
>
> + bool uhs2_sd_tran;
> + bool uhs2_app_cmd; /* Host UHS-II APP Command */
> struct sd_uhs2_caps uhs2_caps; /* Host UHS-II capabilities */
>
> int fixed_drv_type; /* fixed driver type for non-removable media */
> @@ -737,6 +746,12 @@ static inline void mmc_debugfs_err_stats_inc(struct mmc_host *host,
> host->err_stats[stat] += 1;
> }
>
> +static inline int mmc_card_uhs2_hd_mode(struct mmc_host *host)
> +{
> + return host->ios.timing == MMC_TIMING_UHS2_SPEED_A_HD ||
> + host->ios.timing == MMC_TIMING_UHS2_SPEED_B_HD;
> +}
> +
> int mmc_sd_switch(struct mmc_card *card, int mode, int group, u8 value, u8 *resp);
> int mmc_send_status(struct mmc_card *card, u32 *status);
> int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> --
> 2.25.1
>