Re: [PATCH v2 0/6] firmware: arm_scmi: Add SCMI v3.2 pincontrol protocol basic support

From: AKASHI Takahiro
Date: Thu Jan 04 2024 - 20:38:07 EST


On Thu, Jan 04, 2024 at 06:48:44PM +0800, Peng Fan (OSS) wrote:
> This patchset is a rework from Oleksii's RFC v5 patchset
> https://lore.kernel.org/all/cover.1698353854.git.oleksii_moisieiev@xxxxxxxx/
>
> This patchset introduces some changes based on RFC v5:
> - introduce helper get_max_msg_size
> - support compatible string
> - iterate the id_table
> - Support multiple configs in one command
> - Added i.MX support
> - Patch 5 firmware: arm_scmi: Add SCMI v3.2 pincontrol protocol basic support
> is almost same as RFCv5 expect multiple configs support.
> - Patch 4 the dt-bindings includes compatible string to support i.MX
> - Rebased on 2023-12-15 linux-next/master

For the record, the translation of pin config types,
pinctrl_scmi_map_pinconf_type(), is finally implemented in patch 4.

Thanks,
-Takahiro Akashi

> If any comments from RFC v5 are missed, I am sorry in advance.
>
> This PINCTRL Protocol is following Version 3.2 SCMI Spec Beta release.
>
> On ARM-based systems, a separate Cortex-M based System Control Processor
> (SCP) provides control on pins, as well as with power, clocks, reset
> controllers. So implement the driver to support such cases.
>
> The i.MX95 Example as below:
>
> Configuration:
> The scmi-pinctrl driver can be configured using DT bindings.
> For example:
> / {
> sram0: sram@445b1000 {
> compatible = "mmio-sram";
> reg = <0x0 0x445b1000 0x0 0x400>;
>
> #address-cells = <1>;
> #size-cells = <1>;
> ranges = <0x0 0x0 0x445b1000 0x400>;
>
> scmi_buf0: scmi-sram-section@0 {
> compatible = "arm,scmi-shmem";
> reg = <0x0 0x80>;
> };
>
> scmi_buf1: scmi-sram-section@80 {
> compatible = "arm,scmi-shmem";
> reg = <0x80 0x80>;
> };
> };
>
> firmware {
> scmi {
> compatible = "arm,scmi";
> mboxes = <&mu2 5 0>, <&mu2 3 0>, <&mu2 3 1>;
> shmem = <&scmi_buf0>, <&scmi_buf1>;
> #address-cells = <1>;
> #size-cells = <0>;
>
> scmi_iomuxc: protocol@19 {
> compatible = "fsl,imx95-scmi-pinctrl";
> reg = <0x19>;
> };
> };
> };
> };
>
> &scmi_iomuxc {
> pinctrl_tpm3: tpm3grp {
> fsl,pins = <
> IMX95_PAD_GPIO_IO12__TPM3_CH2 0x51e
> >;
> };
> };
>
> This patchset has been tested on i.MX95-19x19-EVK board.
>
> Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
> ---
> Changes in v2:
> Added comments, and added R-b for Patch 1
> Moved the compatile string and i.MX patch to the end, marked NOT APPLY
> Patchset based on lore.kernel.org/all/20231221151129.325749-1-cristian.marussi@xxxxxxx/
> Addressed the binding doc issue, dropped i.MX content.
> For the firmware pinctrl scmi driver, addressed the comments from Cristian
> For the pinctrl scmi driver, addressed comments from Cristian
>
> For the i.MX95 OEM stuff, I not have good idea, expect using compatbile
> string. Maybe the firmware public an protocol attribute to indicate it is
> VENDOR stuff or NXP use a new protocol id, not 0x19. But I think
> current pinctrl-scmi.c not able to support OEM config, should we extend
> it with some method? Anyway if patch 1-4 is good enough, they could
> be picked up first.
>
> Since I am only able to test the patch on i.MX95 which not support
> geneirc pinconf, only OEM configs are tested in my side.
>
> ---
> Oleksii Moisieiev (1):
> firmware: arm_scmi: Add SCMI v3.2 pincontrol protocol basic support
>
> Peng Fan (5):
> firmware: arm_scmi: introduce helper get_max_msg_size
> dt-bindings: firmware: arm,scmi: support pinctrl protocol
> pinctrl: Implementation of the generic scmi-pinctrl driver
> [NOT APPLY]firmware: scmi: support compatible string
> [NOT APPLY] pinctrl: scmi: implement pinctrl_scmi_imx_dt_node_to_map
>
> .../devicetree/bindings/firmware/arm,scmi.yaml | 50 ++
> MAINTAINERS | 7 +
> drivers/firmware/arm_scmi/Makefile | 1 +
> drivers/firmware/arm_scmi/bus.c | 39 +-
> drivers/firmware/arm_scmi/common.h | 2 +-
> drivers/firmware/arm_scmi/driver.c | 32 +-
> drivers/firmware/arm_scmi/pinctrl.c | 930 +++++++++++++++++++++
> drivers/firmware/arm_scmi/protocols.h | 3 +
> drivers/pinctrl/Kconfig | 11 +
> drivers/pinctrl/Makefile | 1 +
> drivers/pinctrl/pinctrl-scmi-imx.c | 117 +++
> drivers/pinctrl/pinctrl-scmi.c | 540 ++++++++++++
> drivers/pinctrl/pinctrl-scmi.h | 12 +
> include/linux/scmi_protocol.h | 75 ++
> 14 files changed, 1806 insertions(+), 14 deletions(-)
> ---
> base-commit: 8f266a167d1f0ca34668f05cd8c01bd245c8698b
> change-id: 20231215-pinctrl-scmi-4c5b0374f4c6
>
> Best regards,
> --
> Peng Fan <peng.fan@xxxxxxx>
>