[PATCH v3 7/8] drm/panel: nt35510: move hardwired parameters to configuration
From: Dario Binacchi
Date: Thu Jan 04 2024 - 02:26:10 EST
This patch, preparatory for future developments, move the hardwired
parameters to configuration data to allow the addition of new
NT35510-based panels.
Signed-off-by: Dario Binacchi <dario.binacchi@xxxxxxxxxxxxxxxxxxxx>
---
(no changes since v2)
Changes in v2:
- Re-write the patch [7/8] "drm/panel: nt35510: refactor panel initialization"
in the same style as the original driver in order to maintain the same
structure.
drivers/gpu/drm/panel/panel-novatek-nt35510.c | 140 ++++++++++++++----
1 file changed, 115 insertions(+), 25 deletions(-)
diff --git a/drivers/gpu/drm/panel/panel-novatek-nt35510.c b/drivers/gpu/drm/panel/panel-novatek-nt35510.c
index d6dceb858008..ce8969f48286 100644
--- a/drivers/gpu/drm/panel/panel-novatek-nt35510.c
+++ b/drivers/gpu/drm/panel/panel-novatek-nt35510.c
@@ -171,6 +171,10 @@ struct nt35510_config {
* timing in the display controller.
*/
const struct drm_display_mode mode;
+ /**
+ * @mode_flags: DSI operation mode related flags
+ */
+ unsigned long mode_flags;
/**
* @avdd: setting for AVDD ranging from 0x00 = 6.5V to 0x14 = 4.5V
* in 0.1V steps the default is 0x05 which means 6.0V
@@ -273,6 +277,100 @@ struct nt35510_config {
* same layout of bytes as @vgp.
*/
u8 vgn[NT35510_P1_VGN_LEN];
+ /**
+ * @dopctr: setting optional control for display
+ * ERR bits 0..1 in the first byte is the ERR pin output signal setting.
+ * 0 = Disable, ERR pin output low
+ * 1 = ERR pin output CRC error only
+ * 2 = ERR pin output ECC error only
+ * 3 = ERR pin output CRC and ECC error
+ * The default is 0.
+ * N565 bit 2 in the first byte is the 16-bit/pixel format selection.
+ * 0 = R[4:0] + G[5:3] & G[2:0] + B[4:0]
+ * 1 = G[2:0] + R[4:0] & B[4:0] + G[5:3]
+ * The default is 0.
+ * DIS_EoTP_HS bit 3 in the first byte is "DSI protocol violation" error
+ * reporting.
+ * 0 = reporting when error
+ * 1 = not reporting when error
+ * DSIM bit 4 in the first byte is the video mode data type enable
+ * 0 = Video mode data type disable
+ * 1 = Video mode data type enable
+ * The default is 0.
+ * DSIG bit 5 int the first byte is the generic r/w data type enable
+ * 0 = Generic r/w disable
+ * 1 = Generic r/w enable
+ * The default is 0.
+ * DSITE bit 6 in the first byte is TE line enable
+ * 0 = TE line is disabled
+ * 1 = TE line is enabled
+ * The default is 0.
+ * RAMKP bit 7 in the first byte is the frame memory keep/loss in
+ * sleep-in mode
+ * 0 = contents loss in sleep-in
+ * 1 = contents keep in sleep-in
+ * The default is 0.
+ * CRL bit 1 in the second byte is the source driver data shift
+ * direction selection. This bit is XOR operation with bit RSMX
+ * of 3600h command.
+ * 0 (RMSX = 0) = S1 -> S1440
+ * 0 (RMSX = 1) = S1440 -> S1
+ * 1 (RMSX = 0) = S1440 -> S1
+ * 1 (RMSX = 1) = S1 -> S1440
+ * The default is 0.
+ * CTB bit 2 in the second byte is the vertical scanning direction
+ * selection for gate control signals. This bit is XOR operation
+ * with bit ML of 3600h command.
+ * 0 (ML = 0) = Forward (top -> bottom)
+ * 0 (ML = 1) = Reverse (bottom -> top)
+ * 1 (ML = 0) = Reverse (bottom -> top)
+ * 1 (ML = 1) = Forward (top -> bottom)
+ * The default is 0.
+ * CRGB bit 3 in the second byte is RGB-BGR order selection. This
+ * bit is XOR operation with bit RGB of 3600h command.
+ * 0 (RGB = 0) = RGB/Normal
+ * 0 (RGB = 1) = BGR/RB swap
+ * 1 (RGB = 0) = BGR/RB swap
+ * 1 (RGB = 1) = RGB/Normal
+ * The default is 0.
+ * TE_PWR_SEL bit 4 in the second byte is the TE output voltage
+ * level selection (only valid when DSTB_SEL = 0 or DSTB_SEL = 1,
+ * VSEL = High and VDDI = 1.665~3.3V).
+ * 0 = TE output voltage level is VDDI
+ * 1 = TE output voltage level is VDDA
+ * The default is 0.
+ */
+ u8 dopctr[NT35510_P0_DOPCTR_LEN];
+ /**
+ * @madctl: Memory data access control
+ * RSMY bit 0 is flip vertical. Flips the display image top to down.
+ * RSMX bit 1 is flip horizontal. Flips the display image left to right.
+ * MH bit 2 is the horizontal refresh order.
+ * RGB bit 3 is the RGB-BGR order.
+ * 0 = RGB color sequence
+ * 1 = BGR color sequence
+ * ML bit 4 is the vertical refresh order.
+ * MV bit 5 is the row/column exchange.
+ * MX bit 6 is the column address order.
+ * MY bit 7 is the row address order.
+ */
+ u8 madctl;
+ /**
+ * @sdhdtctr: source output data hold time
+ * 0x00..0x3F = 0..31.5us in steps of 0.5us
+ * The default is 0x05 = 2.5us.
+ */
+ u8 sdhdtctr;
+ /**
+ * @gseqctr: EQ control for gate signals
+ * GFEQ_XX[3:0]: time setting of EQ step for falling edge in steps
+ * of 0.5us.
+ * The default is 0x07 = 3.5us
+ * GREQ_XX[7:4]: time setting of EQ step for rising edge in steps
+ * of 0.5us.
+ * The default is 0x07 = 3.5us
+ */
+ u8 gseqctr[NT35510_P0_GSEQCTR_LEN];
/**
* @sdeqctr: Source driver control settings, first byte is
* 0 for mode 1 and 1 for mode 2. Mode 1 uses two steps and
@@ -536,46 +634,28 @@ static int nt35510_setup_display(struct nt35510 *nt)
{
struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev);
const struct nt35510_config *conf = nt->conf;
- u8 dopctr[NT35510_P0_DOPCTR_LEN];
- u8 gseqctr[NT35510_P0_GSEQCTR_LEN];
u8 dpfrctr[NT35510_P0_DPFRCTR1_LEN];
- /* FIXME: set up any rotation (assume none for now) */
- u8 addr_mode = NT35510_ROTATE_0_SETTING;
- u8 val;
int ret;
- /* Enable TE, EoTP and RGB pixel format */
- dopctr[0] = NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP |
- NT35510_DOPCTR_0_N565;
- dopctr[1] = NT35510_DOPCTR_1_CTB;
ret = nt35510_send_long(nt, dsi, NT35510_P0_DOPCTR,
NT35510_P0_DOPCTR_LEN,
- dopctr);
+ conf->dopctr);
if (ret)
return ret;
- ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &addr_mode,
- sizeof(addr_mode));
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &conf->madctl,
+ sizeof(conf->madctl));
if (ret < 0)
return ret;
- /*
- * Source data hold time, default 0x05 = 2.5us
- * 0x00..0x3F = 0 .. 31.5us in steps of 0.5us
- * 0x0A = 5us
- */
- val = 0x0A;
- ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &val,
- sizeof(val));
+ ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &conf->sdhdtctr,
+ sizeof(conf->sdhdtctr));
if (ret < 0)
return ret;
- /* EQ control for gate signals, 0x00 = 0 us */
- gseqctr[0] = 0x00;
- gseqctr[1] = 0x00;
ret = nt35510_send_long(nt, dsi, NT35510_P0_GSEQCTR,
NT35510_P0_GSEQCTR_LEN,
- gseqctr);
+ conf->gseqctr);
if (ret)
return ret;
@@ -896,7 +976,6 @@ static int nt35510_probe(struct mipi_dsi_device *dsi)
*/
dsi->hs_rate = 349440000;
dsi->lp_rate = 9600000;
- dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS;
/*
* Every new incarnation of this display must have a unique
@@ -908,6 +987,8 @@ static int nt35510_probe(struct mipi_dsi_device *dsi)
return -ENODEV;
}
+ dsi->mode_flags = nt->conf->mode_flags;
+
nt->supplies[0].supply = "vdd"; /* 2.3-4.8 V */
nt->supplies[1].supply = "vddi"; /* 1.65-3.3V */
ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(nt->supplies),
@@ -1030,6 +1111,7 @@ static const struct nt35510_config nt35510_hydis_hva40wv1 = {
.vtotal = 800 + 2 + 0 + 5, /* VBP = 5 */
.flags = 0,
},
+ .mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS,
/* 0x09: AVDD = 5.6V */
.avdd = { 0x09, 0x09, 0x09 },
/* 0x34: PCK = Hsync/2, BTP = 2 x VDDB */
@@ -1050,6 +1132,14 @@ static const struct nt35510_config nt35510_hydis_hva40wv1 = {
.vgp = { 0x00, 0xA3, 0x00 },
/* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
.vgn = { 0x00, 0xA3, 0x00 },
+ /* Enable TE, EoTP and RGB pixel format */
+ .dopctr = { NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP |
+ NT35510_DOPCTR_0_N565, NT35510_DOPCTR_1_CTB },
+ .madctl = NT35510_ROTATE_180_SETTING,
+ /* 0x0A: SDT = 5 us */
+ .sdhdtctr = 0x0A,
+ /* EQ control for gate signals, 0x00 = 0 us */
+ .gseqctr = { 0x00, 0x00 },
/* SDEQCTR: source driver EQ mode 2, 2.5 us rise time on each step */
.sdeqctr = { 0x01, 0x05, 0x05, 0x05 },
/* SDVPCTR: Normal operation off color during v porch */
--
2.43.0