[PATCH v3 1/5] net: mdio: ipq4019: move eth_ldo_rdy before MDIO bus register

From: Luo Jie
Date: Thu Dec 14 2023 - 04:03:51 EST


The ethernet LDO provides the clock for the ethernet PHY that
is connected with PCS, each LDO enables the clock output to
each PCS, after the clock output enablement, the PHY GPIO reset
can take effect.

For the PHY taking the MDIO bus level GPIO reset, the ethernet
LDO should be enabled before the MDIO bus register.

For example, the qca8084 PHY takes the MDIO bus level GPIO
reset for quad PHYs, there is another reason for qca8084 PHY
using MDIO bus level GPIO reset instead of PHY level GPIO
reset as below.

The work sequence of qca8084:
1. enable ethernet LDO.
2. GPIO reset on quad PHYs.
3. register clock provider based on MDIO device of qca8084.
4. PHY probe function called for initializing common clocks.
5. PHY capabilities acquirement.

If qca8084 takes PHY level GPIO reset in the step 4, the clock
provider of qca8084 can't be registered correctly, since the
clock parent(reading the current qca8084 hardware registers in
step 3) of the registered clocks is deserted after GPIO reset.

There are two PCS(UNIPHY) supported in SOC side on ipq5332,
and three PCS(UNIPHY) supported on ipq9574.

Signed-off-by: Luo Jie <quic_luoj@xxxxxxxxxxx>
---
drivers/net/mdio/mdio-ipq4019.c | 51 +++++++++++++++++++++------------
1 file changed, 32 insertions(+), 19 deletions(-)

diff --git a/drivers/net/mdio/mdio-ipq4019.c b/drivers/net/mdio/mdio-ipq4019.c
index abd8b508ec16..5273864fabb3 100644
--- a/drivers/net/mdio/mdio-ipq4019.c
+++ b/drivers/net/mdio/mdio-ipq4019.c
@@ -37,9 +37,12 @@

#define IPQ_PHY_SET_DELAY_US 100000

+/* Maximum SOC PCS(uniphy) number on IPQ platform */
+#define ETH_LDO_RDY_CNT 3
+
struct ipq4019_mdio_data {
- void __iomem *membase;
- void __iomem *eth_ldo_rdy;
+ void __iomem *membase;
+ void __iomem *eth_ldo_rdy[ETH_LDO_RDY_CNT];
struct clk *mdio_clk;
};

@@ -206,19 +209,8 @@ static int ipq4019_mdio_write_c22(struct mii_bus *bus, int mii_id, int regnum,
static int ipq_mdio_reset(struct mii_bus *bus)
{
struct ipq4019_mdio_data *priv = bus->priv;
- u32 val;
int ret;

- /* To indicate CMN_PLL that ethernet_ldo has been ready if platform resource 1
- * is specified in the device tree.
- */
- if (priv->eth_ldo_rdy) {
- val = readl(priv->eth_ldo_rdy);
- val |= BIT(0);
- writel(val, priv->eth_ldo_rdy);
- fsleep(IPQ_PHY_SET_DELAY_US);
- }
-
/* Configure MDIO clock source frequency if clock is specified in the device tree */
ret = clk_set_rate(priv->mdio_clk, IPQ_MDIO_CLK_RATE);
if (ret)
@@ -236,7 +228,7 @@ static int ipq4019_mdio_probe(struct platform_device *pdev)
struct ipq4019_mdio_data *priv;
struct mii_bus *bus;
struct resource *res;
- int ret;
+ int ret, index;

bus = devm_mdiobus_alloc_size(&pdev->dev, sizeof(*priv));
if (!bus)
@@ -252,11 +244,32 @@ static int ipq4019_mdio_probe(struct platform_device *pdev)
if (IS_ERR(priv->mdio_clk))
return PTR_ERR(priv->mdio_clk);

- /* The platform resource is provided on the chipset IPQ5018 */
- /* This resource is optional */
- res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
- if (res)
- priv->eth_ldo_rdy = devm_ioremap_resource(&pdev->dev, res);
+ /* These platform resources are provided on the chipset IPQ5018 or
+ * IPQ5332.
+ */
+ /* This resource are optional */
+ for (index = 0; index < ETH_LDO_RDY_CNT; index++) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, index + 1);
+ if (res) {
+ priv->eth_ldo_rdy[index] = devm_ioremap(&pdev->dev,
+ res->start,
+ resource_size(res));
+
+ /* The ethernet LDO enable is necessary to reset PHY
+ * by GPIO, some PHY(such as qca8084) GPIO reset uses
+ * the MDIO level reset, so this function should be
+ * called before the MDIO bus register.
+ */
+ if (priv->eth_ldo_rdy[index]) {
+ u32 val;
+
+ val = readl(priv->eth_ldo_rdy[index]);
+ val |= BIT(0);
+ writel(val, priv->eth_ldo_rdy[index]);
+ fsleep(IPQ_PHY_SET_DELAY_US);
+ }
+ }
+ }

bus->name = "ipq4019_mdio";
bus->read = ipq4019_mdio_read_c22;
--
2.42.0