On Wed, Dec 13, 2023 at 04:04:57PM +0530, Sanath S wrote:I gave it a thought yesterday and we can do something like this:
On 12/13/2023 11:53 AM, Mika Westerberg wrote:Rigth, it should be enough to reset the protocol adapter config and path
On Wed, Dec 13, 2023 at 08:18:06AM +0200, Mika Westerberg wrote:If we don't tear down of tunnels before performing the DPR, the PCIe
On Wed, Dec 13, 2023 at 07:49:14AM +0200, Mika Westerberg wrote:
On Wed, Dec 13, 2023 at 12:46:35AM +0530, Sanath S wrote:
Boot firmware might have created tunnels of its own. Since we cannotWhy this is needed?
be sure they are usable for us. Tear them down and reset the ports
to handle it as a new hotplug for USB3 routers.
Suggested-by: Mario Limonciello <mario.limonciello@xxxxxxx>
Signed-off-by: Sanath S <Sanath.S@xxxxxxx>
---
drivers/thunderbolt/tb.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/thunderbolt/tb.c b/drivers/thunderbolt/tb.c
index fd49f86e0353..febd0b6972e3 100644
--- a/drivers/thunderbolt/tb.c
+++ b/drivers/thunderbolt/tb.c
@@ -2598,6 +2598,17 @@ static int tb_start(struct tb *tb)
tb_switch_tmu_enable(tb->root_switch);
/* Full scan to discover devices added before the driver was loaded. */
tb_scan_switch(tb->root_switch);
+ /*
+ * Boot firmware might have created tunnels of its own. Since we cannot
+ * be sure they are usable for us, Tear them down and reset the ports
+ * to handle it as new hotplug for USB4 routers.
+ */
+ if (tb_switch_is_usb4(tb->root_switch)) {
+ tb_switch_discover_tunnels(tb->root_switch,
+ &tcm->tunnel_list, false);
It should be enough, to do simply something like this:
if (tb_switch_is_usb4(tb->root_switch))
tb_switch_reset(tb->root_switch);
enumeration is failing.
PCIe link is not coming up after DPR. Below log is missing without
performing path
deactivation before performing DPR and hence PCIe enumeration is not
initiated.
[ 746.630865] pcieport 0000:00:03.1: pciehp: Slot(0-1): Card present
[ 746.630885] pcieport 0000:00:03.1: pciehp: Slot(0-1): Link Up
I think when we do a DPR, it internally does some handling with PCI Path
Enable bit(PE).
So, deactivation of PCIe path is necessary for DPR to work.
config spaces. I guess using discovery at this point is fine too but I
would at least check how complex doing the minimal "reset" turns out.
I mean in tb_switch_reset() for USB4 v1 routers it can go over all the
adapters and perform "cleanup" or so.
Well you are effectively doing that here, no? You "reset" the hostIs host_reset necessary for USB4 v1 routers ? I did not use host_reset inActually this needs to be done only for USB4 v1 routers since we alreadyOh, and would it be possible to tie this with the "host_reset" parameter
reset USB4 v2 hosts so something like:
/*
* Reset USB4 v1 host router to get rid of possible tunnels the
* boot firmware created. This makes sure all the tunnels are
* created by us and thus have known configuration.
*
* For USB4 v2 and beyond we do this in nhi_reset() using the
* host router reset interface.
*/
if (usb4_switch_version(tb->root_switch) == 1)
tb_switch_reset(tb->root_switch);
(possibly add similar comment to the nhi_reset() to refer this one).
too somehow? I guess it could be moved to "tb.c" and "tb.h" and then
check it from nhi.c as already done and then here so this would become:
if (host_reset && usb4_switch_version(tb->root_switch) == 1)
tb_switch_reset(tb->root_switch);
this case.
If its needed, then we have to modify to enable host_reset in nhi.c as well.
router therefore tying this to the same command line parameter makes
sense and allows user an "escape hatch" if this turns out breaking
things.