Re: [PATCH v5 1/7] serial: Do not hold the port lock when setting rx-during-tx GPIO

[Hugo Villeneuve]

On Sat,  9 Dec 2023 13:58:30 +0100
Lino Sanfilippo <l.sanfilippo@xxxxxxxxxx> wrote:

> Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
> Since this function is called with the port lock held, this can be an
> problem in case that setting the GPIO line can sleep (e.g. if a GPIO
> expander is used which is connected via SPI or I2C).
> 
> Avoid this issue by moving the GPIO setting outside of the port lock into
> the serial core and thus making it a generic feature.
> 
> Fixes: c54d48543689 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
> Fixes: ca530cfa968c ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
> Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
> Cc: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
> Cc: stable@xxxxxxxxxxxxxxx
> Signed-off-by: Lino Sanfilippo <l.sanfilippo@xxxxxxxxxx>
> ---
>  drivers/tty/serial/imx.c         |  4 ----
>  drivers/tty/serial/serial_core.c | 12 ++++++++++++
>  drivers/tty/serial/stm32-usart.c |  5 +----
>  3 files changed, 13 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
> index 708b9852a575..9cffeb23112b 100644
> --- a/drivers/tty/serial/imx.c
> +++ b/drivers/tty/serial/imx.c
> @@ -1943,10 +1943,6 @@ static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termio
>  	    rs485conf->flags & SER_RS485_RX_DURING_TX)
>  		imx_uart_start_rx(port);
>  
> -	if (port->rs485_rx_during_tx_gpio)
> -		gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
> -					 !!(rs485conf->flags & SER_RS485_RX_DURING_TX));
> -
>  	return 0;
>  }
>  
> diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
> index f1348a509552..a0290a5fe8b3 100644
> --- a/drivers/tty/serial/serial_core.c
> +++ b/drivers/tty/serial/serial_core.c
> @@ -1402,6 +1402,16 @@ static void uart_set_rs485_termination(struct uart_port *port,
>  				 !!(rs485->flags & SER_RS485_TERMINATE_BUS));
>  }
>  
> +static void uart_set_rs485_rx_during_tx(struct uart_port *port,
> +					const struct serial_rs485 *rs485)
> +{
> +	if (!(rs485->flags & SER_RS485_ENABLED))
> +		return;
> +
> +	gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
> +				 !!(rs485->flags & SER_RS485_RX_DURING_TX));
> +}
> +
>  static int uart_rs485_config(struct uart_port *port)
>  {
>  	struct serial_rs485 *rs485 = &port->rs485;
> @@ -1413,6 +1423,7 @@ static int uart_rs485_config(struct uart_port *port)
>  
>  	uart_sanitize_serial_rs485(port, rs485);
>  	uart_set_rs485_termination(port, rs485);
> +	uart_set_rs485_rx_during_tx(port, rs485);
>  
>  	uart_port_lock_irqsave(port, &flags);
>  	ret = port->rs485_config(port, NULL, rs485);
> @@ -1457,6 +1468,7 @@ static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
>  		return ret;
>  	uart_sanitize_serial_rs485(port, &rs485);
>  	uart_set_rs485_termination(port, &rs485);
> +	uart_set_rs485_rx_during_tx(port, &rs485);
>  
>  	uart_port_lock_irqsave(port, &flags);
>  	ret = port->rs485_config(port, &tty->termios, &rs485);
> diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
> index 3048620315d6..ec9a72a5bea9 100644
> --- a/drivers/tty/serial/stm32-usart.c
> +++ b/drivers/tty/serial/stm32-usart.c
> @@ -226,10 +226,7 @@ static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *ter
>  
>  	stm32_usart_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
>  
> -	if (port->rs485_rx_during_tx_gpio)
> -		gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
> -					 !!(rs485conf->flags & SER_RS485_RX_DURING_TX));
> -	else
> +	if (!port->rs485_rx_during_tx_gpio)
>  		rs485conf->flags |= SER_RS485_RX_DURING_TX;
>  
>  	if (rs485conf->flags & SER_RS485_ENABLED) {
> -- 
> 2.42.0
> 

Reviewed-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>

Hugo