Re: [PATCH 0/3] net: microchip_t1s: additional phy support and collision detect handling

[Ramón Nordin Rodriguez]

On Mon, Nov 27, 2023 at 05:03:54PM +0100, Andrew Lunn wrote:
> > * 3-4 nodes (depending on how many usb ports and dongles I have)
> > * run iperf with long cables and CSMA/CD
> > * run iperf with long cables and CMSA/No CD
> > 
> > I'll report back the results. Anything you'd like to add/focus on with
> > evaluation?
> 
> Humm, thinking about how CSMA/CD works...
> 
> Maybe look at what counters the MAC provides. Does it have collisions
> and bad FCS? A collision should result in a bad FCS, if you are not
> using CD. So if things are working correctly, the count for CD should
> move to FCS if you turn CD off. If CD is falsely triggering, FCS as a
> % should not really change, but you probably get more frames over the
> link?
> 

# setup

Andrew suggested that I try to get statistics from the MAC, I did some
investigation here but could not figure it out.

Using iperf3
Client: Arm based system running lan865x macphy 
Server: PC running lan867x revB usb dongle


# test results

The results below should be considered fairly represenative but far from
perfect. There was some bounce up and down when rerunning, but these resutls
are an eye-ball average.

No meaningful difference was seen with short (2m) cables or long (12m).

## with collision detection enabled

iperf3 normal
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  5.54 MBytes  4.65 Mbits/sec    0             sender
[  5]   0.00-10.01  sec  5.40 MBytes  4.53 Mbits/sec                  receiver

iperf3 reverse
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec   929 KBytes   761 Kbits/sec  293             sender
[  5]   0.00-10.00  sec   830 KBytes   680 Kbits/sec                  receiver


## with collision detection disabled

iperf3 normal
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  6.39 MBytes  5.36 Mbits/sec    0             sender
[  5]   0.00-10.04  sec  6.19 MBytes  5.17 Mbits/sec                  receiver

iperf3 reverse
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.27  sec  1.10 MBytes   897 Kbits/sec  268             sender
[  5]   0.00-10.00  sec  1.01 MBytes   843 Kbits/sec                  receiver

# Conclusions

The arm system running the lan865x macphy uses a not yet mainlined driver, see
https://lore.kernel.org/all/20231023154649.45931-1-Parthiban.Veerasooran@xxxxxxxxxxxxx/

The lan865x driver crashed out every once in a while on reverse mode, there
is definetly something biased in the driver for tx over rx.
Then again it's not accepted yet.

Disabling collision detection seemes to have an positive effect.
Slightly higher speeds and slightly fewer retransmissions.

I don't have a black and white result to present, but things seems to work
slightly better with CD disabled, so I'm leaning towards just unconditionally 
disabling it for the lan865x and lan867x phys for the v2 patch.

I'll wait with submitting v2 for a day so anyone interested gets a
chance to weigh in on this.

R