Re: [PATCH 1/2] dt-bindings: iio: frequency: add admfm2000

[Krzysztof Kozlowski]

On 16/11/2023 01:56, Kim Seer Paller wrote:
> Dual microwave down converter module with input RF and LO frequency
> ranges from 0.5 to 32 GHz and an output IF frequency range from 0.1 to
> 8 GHz. It consists of a LNA, mixer, IF filter, DSA, and IF amplifier
> for each down conversion path.
> 
> Signed-off-by: Kim Seer Paller <kimseer.paller@xxxxxxxxxx>
> ---

...

> +
> +title: ADMFM2000 Dual Microwave Down Converter
> +
> +maintainers:
> +  - Kim Seer Paller <kimseer.paller@xxxxxxxxxx>
> +
> +description: |

Do not need '|' unless you need to preserve formatting.

> +    Dual microwave down converter module with input RF and LO frequency ranges
> +    from 0.5 to 32 GHz and an output IF frequency range from 0.1 to 8 GHz.
> +    It consists of a LNA, mixer, IF filter, DSA, and IF amplifier for each down
> +    conversion path.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,admfm2000
> +
> +  switch1-gpios:
> +    description:
> +      Must contain an array of 2 GPIO specifiers, referring to the GPIO pins

That's obvious. Instead say which pins are this.

> +      connected to the channel 1 switch controls.
> +    minItems: 2
> +    maxItems: 2
> +
> +  switch2-gpios:
> +    description:
> +      Must contain an array of 2 GPIO specifiers, referring to the GPIO pins
> +      connected to the channel 2 switch controls.
> +    minItems: 2
> +    maxItems: 2
> +
> +  attenuation1-gpios:
> +    description:
> +      Must contain an array of 5 GPIO specifiers, referring to the GPIO pins
> +      connected to the channel 1 DSA attenuation controls.
> +    minItems: 5
> +    maxItems: 5
> +
> +  attenuation2-gpios:
> +    description:
> +      Must contain an array of 5 GPIO specifiers, referring to the GPIO pins
> +      connected to the channel 2 DSA attenuation controls.
> +    minItems: 5
> +    maxItems: 5
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 0
> +
> +patternProperties:
> +  "^channel@[0-1]$":
> +    type: object
> +    description: Represents a channel of the device.

Missing additionalProperties: false. Look at other bindings.

> +
> +    properties:
> +      reg:
> +        description:
> +          The channel number.
> +        minimum: 0
> +        maximum: 1
> +
> +      adi,mode:
> +        description:
> +          RF path selected for the channel.
> +            0 - Direct IF mode
> +            1 - Mixer mode
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        enum: [0, 1]
> +
> +    required:
> +      - reg
> +      - adi,mode
> +
> +required:
> +  - compatible
> +  - switch1-gpios
> +  - switch2-gpios
> +  - attenuation1-gpios
> +  - attenuation2-gpios
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    admfm2000 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


> +      compatible = "adi,admfm2000";
> +
> +      switch1-gpios = <&gpio 1 GPIO_ACTIVE_LOW>,
> +        <&gpio 2 GPIO_ACTIVE_HIGH>;

Align this with previous <

> +
> +      switch2-gpios = <&gpio 3 GPIO_ACTIVE_LOW>,
> +        <&gpio 4 GPIO_ACTIVE_HIGH>;
> +
Best regards,
Krzysztof