Re: [PATCH 4/4] arm64: dts: st: add rcc support in stm32mp251

[Krzysztof Kozlowski]

On 06/11/2023 15:18, gabriel.fernandez@xxxxxxxxxxx wrote:
> From: Gabriel Fernandez <gabriel.fernandez@xxxxxxxxxxx>
> 
> Add RCC support used for to manage clocks and resets on stm32mp251.
> 
> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/st/stm32mp251.dtsi | 59 ++++++++++++++------------
>  1 file changed, 31 insertions(+), 28 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/st/stm32mp251.dtsi b/arch/arm64/boot/dts/st/stm32mp251.dtsi
> index 124403f5f1f4..698d0f68b98d 100644
> --- a/arch/arm64/boot/dts/st/stm32mp251.dtsi
> +++ b/arch/arm64/boot/dts/st/stm32mp251.dtsi
> @@ -3,7 +3,9 @@
>   * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
>   * Author: Alexandre Torgue <alexandre.torgue@xxxxxxxxxxx> for STMicroelectronics.
>   */
> +#include <dt-bindings/clock/stm32mp25-clks.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/reset/stm32mp25-resets.h>
>  
>  / {
>  	#address-cells = <2>;
> @@ -35,22 +37,10 @@ arm_wdt: watchdog {
>  	};
>  
>  	clocks {
> -		ck_flexgen_08: ck-flexgen-08 {
> +		clk_rcbsec: clk-rcbsec {
>  			#clock-cells = <0>;
>  			compatible = "fixed-clock";
> -			clock-frequency = <100000000>;
> -		};
> -
> -		ck_flexgen_51: ck-flexgen-51 {
> -			#clock-cells = <0>;
> -			compatible = "fixed-clock";
> -			clock-frequency = <200000000>;
> -		};
> -
> -		ck_icn_ls_mcu: ck-icn-ls-mcu {
> -			#clock-cells = <0>;
> -			compatible = "fixed-clock";
> -			clock-frequency = <200000000>;
> +			clock-frequency = <64000000>;
>  		};
>  	};
>  
> @@ -122,7 +112,7 @@ usart2: serial@400e0000 {
>  				compatible = "st,stm32h7-uart";
>  				reg = <0x400e0000 0x400>;
>  				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> -				clocks = <&ck_flexgen_08>;
> +				clocks = <&rcc CK_KER_USART2>;
>  				status = "disabled";
>  			};
>  
> @@ -131,7 +121,7 @@ sdmmc1: mmc@48220000 {
>  				arm,primecell-periphid = <0x00353180>;
>  				reg = <0x48220000 0x400>, <0x44230400 0x8>;
>  				interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
> -				clocks = <&ck_flexgen_51>;
> +				clocks = <&rcc CK_KER_SDMMC1 >;
>  				clock-names = "apb_pclk";
>  				cap-sd-highspeed;
>  				cap-mmc-highspeed;
> @@ -140,6 +130,19 @@ sdmmc1: mmc@48220000 {
>  			};
>  		};
>  
> +		rcc: rcc@44200000 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation


Best regards,
Krzysztof