Re: [PATCH v10 3/3] media: i2c: Add support for alvium camera

[Tommaso Merciai]

Hi Sakari,

On Wed, Nov 01, 2023 at 02:13:14PM +0000, Sakari Ailus wrote:
> Hi Tommaso,
> 
> On Tue, Oct 31, 2023 at 12:46:09PM +0100, Tommaso Merciai wrote:
> > > > +static int alvium_get_dt_data(struct alvium_dev *alvium)
> > > > +{
> > > > +	struct device *dev = &alvium->i2c_client->dev;
> > > > +	struct fwnode_handle *fwnode = dev_fwnode(dev);
> > > > +	struct fwnode_handle *endpoint;
> > > > +	int ret = -EINVAL;
> > > > +
> > > > +	if (!fwnode)
> > > > +		return -EINVAL;
> > > > +
> > > > +	/* Only CSI2 is supported for now: */
> > > > +	alvium->ep.bus_type = V4L2_MBUS_CSI2_DPHY;
> > > > +
> > > > +	endpoint = fwnode_graph_get_endpoint_by_id(fwnode, 0, 0, 0);
> > > > +	if (!endpoint) {
> > > > +		dev_err(dev, "endpoint node not found\n");
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > > +	if (v4l2_fwnode_endpoint_alloc_parse(endpoint, &alvium->ep)) {
> > > > +		dev_err(dev, "could not parse endpoint\n");
> > > > +		goto error_out;
> > > 
> > > This could go to another label to be less confusing, but
> > > v4l2_fwnode_endpoint_free() looks to be a no-op here, so good enough.
> > 
> > Thanks for the comment.
> > To be honest right now this is clear to me
> > I prefere to stay on the following :)
> > Prefer to keep just only one path.
> 
> You can safely call v4l2_fwnode_endpoint_free() on an unparsed endpoint (or
> on and endpoint the parsing of which failed). I prefer this too.
> 
> > > > +		ret = -ENODEV;
> > > > +		goto err_powerdown;
> > > > +	}
> > > > +
> > > > +	ret = alvium_get_hw_info(alvium);
> > > > +	if (ret) {
> > > > +		dev_err(dev, "get_hw_info fail %d\n", ret);
> > > > +		goto err_powerdown;
> > > > +	}
> > > > +
> > > > +	ret = alvium_hw_init(alvium);
> > > > +	if (ret) {
> > > > +		dev_err(dev, "hw_init fail %d\n", ret);
> > > > +		goto err_powerdown;
> > > > +	}
> > > > +
> > > > +	ret = alvium_setup_mipi_fmt(alvium);
> > > > +	if (ret) {
> > > > +		dev_err(dev, "setup_mipi_fmt fail %d\n", ret);
> > > > +		goto err_powerdown;
> > > > +	}
> > > > +
> > > > +	/*
> > > > +	 * Enable runtime PM without autosuspend:
> > > > +	 *
> > > > +	 * Don't use pm autosuspend (alvium have ~7s boot time).
> > > > +	 * Alvium has been powered manually:
> > > > +	 *  - mark it as active
> > > > +	 *  - increase the usage count without resuming the device.
> > > > +	 */
> > > > +	pm_runtime_set_active(dev);
> > > > +	pm_runtime_get_noresume(dev);
> > > > +	pm_runtime_enable(dev);
> > > > +
> > > > +	/* Initialize the V4L2 subdev. */
> > > > +	ret = alvium_subdev_init(alvium);
> > > > +	if (ret)
> > > > +		goto err_pm;
> > > > +
> > > > +	ret = v4l2_async_register_subdev(&alvium->sd);
> > > > +	if (ret < 0) {
> > > > +		dev_err(dev, "Could not register v4l2 device\n");
> > > > +		goto err_subdev;
> > > > +	}
> > > > +
> > > > +	return 0;
> > > > +
> > > > +err_subdev:
> > > > +	alvium_subdev_cleanup(alvium);
> > > 
> > > Should this also be called by the remove function?
> > > Or is it already handled by an un-register mechanism?
> > 
> > Right, I miss this.
> > Thanks.
> > I put this to remove function like:
> > 
> > static void alvium_remove(struct i2c_client *client)
> > {
> > 	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > 	struct alvium_dev *alvium = sd_to_alvium(sd);
> > 	struct device *dev = &alvium->i2c_client->dev;
> > 
> > 	/*
> > 	 * Disable runtime PM. In case runtime PM is disabled in the kernel,
> > 	 * make sure to turn power off manually.
> > 	 */
> > 	pm_runtime_disable(dev);
> > 	if (!pm_runtime_status_suspended(dev))
> > 		alvium_power_on(alvium, false);
> > 	pm_runtime_set_suspended(dev);
> > 
> > 	alvium_subdev_cleanup(alvium);
> > 	i2c_unregister_device(alvium->i2c_client);
> 
> This doesn't belong here (as you didn't register it). It was missed in the
> review earlier.

Arg.. Good catch! Thanks :)
You are right we remove i2c_register into some previous review.

Regards,
Tommaso

> 
> > }
> > 
> > 
> > If for you Cristophe, Sakari, Laurent,
> > it's ok I prefer to skip v11 that I sent this morning too early.
> > I collected hints from Cristophe right now and I plan to send v12
> > this afternoon/evening if for you all is ok.
> > 
> > https://github.com/avs-sas/linux/blob/tm/media_stage/v6.6.0-rc3/alvium_drv/v12/drivers/media/i2c/alvium-csi2.c
> > 
> > Please let me know.
> > 
> > Thanks again to all! :)
> 
> -- 
> Regards,
> 
> Sakari Ailus