Re: [PATCH V2 3/7] i2c: sprd: Use global variables to record I2C ack/nack status instead of local variables

[Baolin Wang]

On 10/23/2023 4:11 PM, Huangzheng Lai wrote:
> We found that when the interrupt bit of the I2C controller is cleared,
> the ack/nack bit is also cleared at the same time. After clearing the
> interrupt bit in sprd_i2c_isr(), incorrect ack/nack information will be
> obtained in sprd_i2c_isr_thread(), resulting in incorrect communication
> when nack cannot be recognized. To solve this problem, we used a global

This is a hardware bug?

> variable to record ack/nack information before clearing the interrupt
> bit instead of a local variable.
>
> Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
> Cc: <stable@xxxxxxxxxxxxxxx> # v4.14+
> Signed-off-by: Huangzheng Lai <Huangzheng.Lai@xxxxxxxxxx>
> ---
>   drivers/i2c/busses/i2c-sprd.c | 11 ++++++-----
>   1 file changed, 6 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-sprd.c b/drivers/i2c/busses/i2c-sprd.c
> index aa602958d4fd..dec627ef408c 100644
> --- a/drivers/i2c/busses/i2c-sprd.c
> +++ b/drivers/i2c/busses/i2c-sprd.c
> @@ -85,6 +85,7 @@ struct sprd_i2c {
>   	struct clk *clk;
>   	u32 src_clk;
>   	u32 bus_freq;
> +	bool ack_flag;
>   	struct completion complete;
>   	struct reset_control *rst;
>   	u8 *buf;
> @@ -119,6 +120,7 @@ static void sprd_i2c_clear_ack(struct sprd_i2c *i2c_dev)
>   {
>   	u32 tmp = readl(i2c_dev->base + I2C_STATUS);
>   
> +	i2c_dev->ack_flag = 0;
>   	writel(tmp & ~I2C_RX_ACK, i2c_dev->base + I2C_STATUS);
>   }
>   
> @@ -393,7 +395,6 @@ static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
>   {
>   	struct sprd_i2c *i2c_dev = dev_id;
>   	struct i2c_msg *msg = i2c_dev->msg;
> -	bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);

Before this patch, we will re-read the ack bit form the register, but 
now we just read it in sprd_i2c_isr(). Is it possible that we will miss 
the ack bit?

>   	u32 i2c_tran;
>   
>   	if (msg->flags & I2C_M_RD)
> @@ -409,7 +410,7 @@ static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
>   	 * For reading data, ack is always true, if i2c_tran is not 0 which
>   	 * means we still need to contine to read data from slave.
>   	 */
> -	if (i2c_tran && ack) {
> +	if (i2c_tran && i2c_dev->ack_flag) {
>   		sprd_i2c_data_transfer(i2c_dev);
>   		return IRQ_HANDLED;
>   	}
> @@ -420,7 +421,7 @@ static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
>   	 * If we did not get one ACK from slave when writing data, we should
>   	 * return -EIO to notify users.
>   	 */
> -	if (!ack)
> +	if (!i2c_dev->ack_flag)
>   		i2c_dev->err = -EIO;
>   	else if (msg->flags & I2C_M_RD && i2c_dev->count)
>   		sprd_i2c_read_bytes(i2c_dev, i2c_dev->buf, i2c_dev->count);
> @@ -437,7 +438,6 @@ static irqreturn_t sprd_i2c_isr(int irq, void *dev_id)
>   {
>   	struct sprd_i2c *i2c_dev = dev_id;
>   	struct i2c_msg *msg = i2c_dev->msg;
> -	bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
>   	u32 i2c_tran;
>   
>   	if (msg->flags & I2C_M_RD)
> @@ -456,7 +456,8 @@ static irqreturn_t sprd_i2c_isr(int irq, void *dev_id)
>   	 * means we can read all data in one time, then we can finish this
>   	 * transmission too.
>   	 */
> -	if (!i2c_tran || !ack) {
> +	i2c_dev->ack_flag = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
> +	if (!i2c_tran || !i2c_dev->ack_flag) {
>   		sprd_i2c_clear_start(i2c_dev);
>   		sprd_i2c_clear_irq(i2c_dev);
>   	}