Re: [PATCH -tip 3/3] x86/percpu: *NOT FOR MERGE* Implement arch_raw_cpu_ptr() with RDGSBASE

[Ingo Molnar]

* Uros Bizjak <ubizjak@xxxxxxxxx> wrote:

> Sean says:
> 
> "A significant percentage of data accesses in Intel's TDX-Module[*] use
> this pattern, e.g. even global data is relative to GS.base in the module
> due its rather odd and restricted environment.  Back in the early days
> of TDX, the module used RD{FS,GS}BASE instead of prefixes to get
> pointers to per-CPU and global data structures in the TDX-Module.  It's
> been a few years so I forget the exact numbers, but at the time a single
> transition between guest and host would have something like ~100 reads
> of FS.base or GS.base.  Switching from RD{FS,GS}BASE to prefixed accesses
> reduced the latency for a guest<->host transition through the TDX-Module
> by several thousand cycles, as every RD{FS,GS}BASE had a latency of
> ~18 cycles (again, going off 3+ year old memories).
> 
> The TDX-Module code is pretty much a pathological worth case scenario,
> but I suspect its usage is very similar to most usage of raw_cpu_ptr(),
> e.g. get a pointer to some data structure and then do multiple
> reads/writes from/to that data structure.
> 
> The other wrinkle with RD{FS,FS}GSBASE is that they are trivially easy

[ Obsessive-compulsive nitpicking:

     s/RD{FS,FS}GSBASE
      /RD{FS,GS}BASE
]

> to emulate. If a hypervisor/VMM is advertising FSGSBASE even when it's
> not supported by hardware, e.g. to migrate VMs to older hardware, then
> every RDGSBASE will end up taking a few thousand cycles
> (#UD -> VM-Exit -> emulate).  I would be surprised if any hypervisor
> actually does this as it would be easier/smarter to simply not advertise
> FSGSBASE if migrating to older hardware might be necessary, e.g. KVM
> doesn't support emulating RD{FS,GS}BASE.  But at the same time, the whole
> reason I stumbled on the TDX-Module's sub-optimal RD{FS,GS}BASE usage was
> because I had hacked KVM to emulate RD{FS,GS}BASE so that I could do KVM
> TDX development on older hardware.  I.e. it's not impossible that this
> code could run on hardware where RDGSBASE is emulated in software.
> 
> {RD,WR}{FS,GS}BASE were added as faster alternatives to {RD,WR}MSR,
> not to accelerate actual accesses to per-CPU data, TLS, etc.  E.g.
> loading a 64-bit base via a MOV to FS/GS is impossible.  And presumably
> saving a userspace controlled by actually accessing FS/GS is dangerous
> for one reason or another.
> 
> The instructions are guarded by a CR4 bit, the ucode cost just to check
> CR4.FSGSBASE is probably non-trivial."

BTW., a side note regarding the very last paragraph and the CR4 bit ucode 
cost, given that SMAP is CR4 controlled too:

 #define X86_CR4_FSGSBASE_BIT    16 /* enable RDWRFSGS support */
 #define X86_CR4_FSGSBASE        _BITUL(X86_CR4_FSGSBASE_BIT)
 ...
 #define X86_CR4_SMAP_BIT        21 /* enable SMAP support */
 #define X86_CR4_SMAP            _BITUL(X86_CR4_SMAP_BIT)

And this modifies the behavior of STAC/CLAC, of which we have ~300 
instances in a defconfig kernel image:

  kepler:~/tip> objdump -wdr vmlinux | grep -w 'stac' x | wc  -l
  119

  kepler:~/tip> objdump -wdr vmlinux | grep -w 'clac' x | wc  -l
  188

Are we certain that ucode on modern x86 CPUs check CR4 for every affected 
instruction?

Could they perhaps use something faster, such as internal 
microcode-patching (is that a thing?), to turn support for certain 
instructions on/off when the relevant CR4 bit is modified, without
having to genuinely access CR4 for every instruction executed?

Thanks,

	Ingo